4G LTE LTE CPE Wireless WiFi Router User Manual

4G LTE LTE CPE Wireless WiFi Router User Manual

Contents hide

1	Power indicator	On：CPE connected to power,indicator is on;
		Off:CPE not connected to power,indicator is off
2	WAN indicator	On:insert SIM card ,successfully registered to 4G/3G network ,indicator turns green；
		Off：CPE not connected to power,or no SIM card,or not registered to network.
3	WiFi indicator	On:when user connected to WIFI , indicator is on.
		Off:CPE power off , indicator off.
4	LAN indicator	On：plug cable to LAN port,indicator is on;
		Off：cable pulled out,indicator off
5	3G/4G indicator	Insert SIM card,successfully registered to 4G/3G network,indicator is on
		4G/3G not registered,indicator off
6	Power port	CPE power input:12V 1A,please use standard power adapter
7	LAN port	To provide cable network to users.
		The first RJ45 port near power port is WAN or LAN , the rest are LAN ports
8	SIM card slot	Insert SIM card to connect to 4G/3G network,support Micro SIM card only
9	Reset button	Long press for 5 seconds,CPE will restore to factory setting,device restart automatically.

Notice: Place the device on a stable surface.

Open the packing box, insert the power adapter into the power port of CPE.
After power on, all indicators will on, then power indicator steady on, WiFi indicator steady on;
Connect the WAN port to Ethernet port, WAN indicator will steady on, it will blinking once data is being transmitted.
Connect the LAN port to the end device, LAN indicator will steady on, it will blinking once data is being transmitted.

Or connect the end device through WiFi, WiFi indicator will blinking once data is being transmitted.

Notice: Place the device on a stable surface.

Insert the standard Micro SIM card as following picture:
Open the packing box, insert the power adapter into the power port of CPE;
After power on, all indicators will on, then power indicator steady on, WiFi indicator steady on;
4G CPE will automatically dial-up, 3G/4G indicator steady on, then blinking, it means the device already connect with Internet

Make sure CPE is turned on, and WiFi is on working;
Power on the end device to enter the WiFi setting;
Click the SSID of CPE, SSID and password are on the sticker of CPE, refer to the right picture;
Enter WiFi password, click connect, WiFi connection is successful after WiFi indicator blinking.

(The WiFi setting interface is different for different end devices, refer to the following device).

CPE

Lm321
SSID:4G-CPE-XXXXXX
Login/password:admin
Router IP:192.168.100.1
WIFI KEY:A1b2c3d4

Make sure the 4G CPE is power on, and your com- puter and mobile phone connected with 4G CPE;
Open the browser of com- puter or mobile phone;
Enter the IP address into the address bar of browser, IP address is as right picture;
Enter the user name and password into the prompt dialog box, user name and password are: admin;
In the main menu of WEB UI, it including CPE status, router setting, WiFi setting,firewall, SMS setting, system management and etc;
After finish the setting, click the apply, the device will restart autom- atically.

Main menu of WEB UI:

Faulty checking:

Power indicator is off, please check if you plug the power adapter properly.
3G/4G indicator is off, please check if you insert SIM card properly.
3G/4G indicator doesn’t blinking:
1. It is searching for the internet while it steady on within 3 minutes;
2. It can’t connect to internet while it steady on more than 3 minutes, please change the CPE into another place.

Notices:

Place the device on a stable surface.
Ideal operating temperatures are -20℃ to 70℃, ideal storage temperatures are -20℃ to +70℃. Extreme heat or cold maydamage your device or accessories.
Keep the device away from sources of fire, water to avoid da- mage your device or accessories.
Do not use your device during thunderstorms to protect your device against any danger caused by lighting.
Do not bend or press the external antenna, otherwise, comm-unication quality may be reduced.