5AT3T4 Outdoor Siren for Ring Alarm Instruction Manual

5AT3T4 Outdoor Siren for Ring Alarm Instruction Manual & troubleshooting

5AT3T4 Outdoor Siren for Ring Alarm Instruction Manual
5AT3T4 Outdoor Siren for Ring Alarm Instruction Manual  & troubleshooting 1

START

Power Sources
The Outdoor Siren can be used with one or more power sources. This guide will show you how to install using the included D Batteries. Visit ring.com/outdoor-siren to learn about other power sources and installation tips.

Included

5AT3T4 Outdoor Siren for Ring Alarm Instruction Manual  & troubleshooting 23 x D Batteries

Sold Seperately

  • 5AT3T4 Outdoor Siren for Ring Alarm Instruction Manual  & troubleshooting 3 Ring Solar Panel & Quick Release Battery Pack
    • Keeps the battery pack charged
  • 5AT3T4 Outdoor Siren for Ring Alarm Instruction Manual  & troubleshooting 4 Hardwired
    • Advanced electrical skills required
    • Supports 9-28V, 12W DC power input and 0.2~2.5mm2 wire
  • 5AT3T4 Outdoor Siren for Ring Alarm Instruction Manual  & troubleshooting 5 Hardwired with Plug-in Adapter (2nd gen.)

Use only accessories supplied with your device, or specifically marketed for use with your device, to power your device.

LOCATION

5AT3T4 Outdoor Siren for Ring Alarm Instruction Manual  & troubleshooting 6

The Outdoor Siren should be mounted on the outside of your home, in a location with:

  • Visibility, so the Outdoor Siren can be seen by anyone passing your home.
  • Safe access, so you can change the batteries safely. If using a ladder, make sure there is solid ground below.
  • Close to a power source, if using backup power.

SETUP

5AT3T4 Outdoor Siren for Ring Alarm Instruction Manual  & troubleshooting 7

Start by opening the Ring app and tap Set up a Device, then tap Security, Sirens, and Outdoor Siren.
Follow the directions in the app.

To scan the QR code, you’ll need to loosen the security screw on the bottom of the mounting bracket, then slide the bracket o¬ of the Outdoor Siren (the screw stays in the bracket).

Pull the battery tab when prompted by the app.

TESTING

5AT3T4 Outdoor Siren for Ring Alarm Instruction Manual  & troubleshooting 8

Press the Test button inside the battery compartment on the back of the Outdoor Siren. The LED lights on the front will flash — this may take up to 30 seconds.

  • Green means the test is successful.
  • Red means the test failed. Try moving a Range Extender between the Outdoor Siren and the alarm system, or find a new wall or area for mounting, then test again.

MOUNTING

5AT3T4 Outdoor Siren for Ring Alarm Instruction Manual  & troubleshooting 9

  1. Hold the mounting bracket at the mounting location and level it using the spirit level.
  2. Mark your holes using the mounting bracket as a guide.
  3. Drill holes using a 6mm drill bit.
  4. Adjust the tamper arm screw to ensure that the arm makes contact with the mounting surface.

POWER

5AT3T4 Outdoor Siren for Ring Alarm Instruction Manual  & troubleshooting 10

Visit ring.com/outdoor-siren to learn how to use the Outdoor Siren with other power sources.

  1. D Cell Batteries
    If you need to replace the batteries, match the + and – icons.
  2. Ring Quick Release Battery
    Carefully insert Quick Release Battery Pack, starting with the pin side first.
  3. Ring Solar Panel connection
    Remove the rubber stopper from the DC Jack, then connect the Solar Panel.
  4. Hardwired Terminals /
    Ring Plug-in Adapter (2nd Generation) Supports 9–28V, 12W DC power input and 0.2~2.5mm2 wire.
  • Do not apply DC power above or below 9–28V, 12W.
  • Do not apply AC power.
  • Do not use wire gauge above or below 0.2~2.5mm2

To install

  1. WARNING: Electrical shock hazard. Always turn off the power before you begin working with electrical wiring.
  2. Loosen the Outdoor Siren’s positive and negative terminals.
  3. Open the rubber cover and thread the wires through.
  4. Connect the positive and negative wires and securely re-tighten the terminals.

SAFETY NOTE: We recommend that you consult a licensed professional electrician if you are not experienced with hardwiring projects. Please use extra caution when using a ladder to minimize the risk of fall.

FINISH AND TEST

5AT3T4 Outdoor Siren for Ring Alarm Instruction Manual  & troubleshooting 11

When you finish connecting your power sources, replace the back cover, then attach the Outdoor Siren to the mounting bracket. Tighten the security screw on the bottom of the bracket. Follow the directions in the app to test the Outdoor Siren.

WARNING: Loud Siren and Strobe lights.

SETTINGS

Using the Ring app, you can adjust the Outdoor Siren LED and audio settings to meet your preferences and comply with local laws. Please check your local laws about the volume and duration of sirens. Visit ring.com/outdoor-siren for more details.

WARRANTY

Find warranty information at: ring.com/warranty

Z-WAVE

For Z-Wave technical information, visit: ring.com/z-wave

Customer Support

Web: ring.com/help
UK +44 1727 26 3045
EU +800 8700 9781

5AT3T4 Outdoor Siren for Ring Alarm Instruction Manual  & troubleshooting 12

5AT3T4 Outdoor Siren for Ring Alarm Instruction Manual  & troubleshooting 13

 

FAQ


Setting up 5AT3T4 Outdoor Siren for Ring Alarm Instruction Manual is easy with these step-by-step instructions. Follow the steps are you are set-up in no time.

Using 5AT3T4 Outdoor Siren for Ring Alarm Instruction Manual is simple by using this manual. Follow the instructions one by one and everything will be fine

Is 5AT3T4 Outdoor Siren for Ring Alarm Instruction Manual stuck or not working properly? By resetting it you can set it back to the standard settings and everything should be back to normal. This works in many cases when problems arise.

This page contains the complete user instructions & manual for 5AT3T4 Outdoor Siren for Ring Alarm Instruction Manual

All symbols, colors and codes for 5AT3T4 Outdoor Siren for Ring Alarm Instruction Manual are explained in this instruction manual. You can find everything you need and moree