ADJ Dotz TPar COB LED Par Wash System Instructions

ADJ Dotz TPar COB LED Par Wash System Instructions & troubleshooting

ADJ Dotz TPar COB LED Par Wash System Instructions  & troubleshooting 1

ADJ Dotz TPar COB LED Par Wash System

ADJ Dotz TPar COB LED Par Wash System Instructions  & troubleshooting 2

Introduction

Unpacking
Thank you for purchasing the Dotz TPar System by ADJ Products, LLC. Every Dotz TPar System has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during ship-ping. If the carton appears to be damaged, carefully inspect your fix-ture for any damage and be sure all accessories necessary to operate the unit has arrived intact. In the case damage has been found or parts are missing, please contact our toll free customer support number for further instructions. Do not return this unit to your dealer without first contacting customer support.
Introduction
The Dotz TPar System is part of ADJ’s continuing pur-suit for creating high quality affordable intelligent fixtures. The Dotz TPar System is a high performance, DMX intelligent, moving head LED fixture. This fixture is a great piece for retail stores, displays, mood, architectural, interior and exterior decoration, and clubs. This unit can be used as a stand alone, or in a Primary/Secondary configuration. The unit can also be controlled via DMX controller. This fixture is suitable for theaters, studios, retail stores, and other similar locations.
Customer Support
ADJ Products, LLC provides a toll free cus-tomer support line, to provide set up help and to answer any question should you encounter problems during your set up or initial operation. You may also visit us on the web at www.adj.com for any comments or suggestions. Service Hours are Monday through Friday 8:00 a.m. to 4:30 p.m. Pacific Standard Time.

To purchase parts online visit http://parts.americandj.com
Warning! To prevent or reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture.  There are no user serviceable parts inside this unit. Do not attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact ADJ Products, LLC. PLEASE recycle the shipping carton when ever possible.

General Instructions

To optimize the performance of this product, please read these operat-ing instructions carefully to familiarize yourself with the basic operations of this unit. These instructions contain important safety information regarding the use and maintenance of this unit. Please keep this manual with the unit, for future reference.

Features

  • 4 x COB LED Par Wash Fixtures
  • 1 x Foot Controller
  • 1 x Lighting Stand
  • 1 x RF Remote Control
  • 1 x Stand Bag
  • 1 x Soft Case for Lighting System
  •  RGB Color Mixing
  •  Strobing
  •  Electronic Dimming 0-100%
  •  Built in Microphone
  •  DMX-512 protocol
  •  Five DMX Modes: 3 Channel Mode, 5 Channel Mode, 9 Channel Mode, 12 Channel Mode, & 18 Channel Mode
  •  4 Operating Modes – Sound Active, Auto Run, Built-In Programs, or DMX Control

Warranty Registration
The Dotz TPar System carries a 2 year (730 days) limited warranty. Please fill out the enclosed warranty card to validate your purchase and warranty. You may also register your product online at www. americandj.com. All returned service items whether under warranty or not, must be freight pre-paid and accompany a return authorization (R.A.) number. If the unit is under warranty you must provide a copy of your proof of purchase invoice. Please contact ADJ Products, LLC customer support for a R.A. number. ADJ Products, LLC – www.adj.com – Dotz TPar System User Manual Page 3

Safety Precautions

  • To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture
  • Do not spill water or other liquids into or on to your unit.
  • Be sure that the local power outlet match that of the required volt- age for your unit.
  • Do not attempt to operate this unit if the power cord has been frayed or broken. Do not attempt to remove or break off the ground prong from the electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal short.
  • Disconnect from main power before making any type of connection.
  • Do not remove the cover under any conditions. There are no user serviceable parts inside.
  • Never operate this unit when it’s cover is removed.
  • Never plug this unit in to a dimmer pack
  • Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between this device and a wall.
  • Do not attempt to operate this unit, if it becomes damaged.
  • This unit is intended for indoor use only, use of this product out` doors voids all warranties.
  • During long periods of non-use, disconnect the unit’s main power.
  • Always mount this unit in safe and stable matter.
  • Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to the point they exit from the unit.
  • Cleaning -The fixture should be cleaned only as recommended by t he manufacturer. See page 23 for cleaning details.
  • Heat -The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (inclu- d ing amplifiers) that produce heat.
  • The fixture should be serviced by qualified service personnel when:
    •  The power-supply cord or the plug has been damaged.
    •  Objects have fallen, or liquid has been spilled into the appliance.
    •  The appliance has been exposed to rain or water.
    •  The appliance does not appear to operate normally or exhibits a marked change in performance.

Set Up

Power Supply: The ADJ Dotz TPar System contains a automatic volt-age switch, which will auto sense the voltage when it is plugged into a power source. With this switch there is no need to worry about the correct power voltage, this unit can be plugged in anywhere. Always use the PowerCon cord that came with the unit.
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-tocol used as a form of communication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that trav-els from fixture to fixture via the DATA “IN” and DATA “OUT” XLR ter-minals located on all DMX fixtures (most controllers only have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller, as long as all fixtures and the controller are DMX compli-ant. To ensure proper DMX data transmission, when using several DMX fixtures try to use the shortest cable path possible. The order in which fixtures are connected in a DMX line does not influence the DMX addressing. For example; a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX Operation):
The Dotz TPar System can be controlled via DMX-512 protocol. The Dotz TPar System has 5 DMX Channel Modes. The DMX address is set on the rear panel of the Dotz TPar System. Your unit and your DMX con-troller require a approved DMX-512 110 Ohm Data cable for data input and data output (Figure 1). We recommend Accu-Cable DMX cables. If you are making your own cables, be sure to use standard 110-120 Ohm shielded cable (This cable may be purchased at almost all professional sound and lighting stores). Your cables should be made with a male and female XLR connector on either end of the cable. Also remember that DMX cable must be daisy chained and cannot be split.ADJ Dotz TPar COB LED Par Wash System Instructions  & troubleshooting 3

Notice: Be sure to follow figures two and three when making your own cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer casing. Grounding the shield could cause a short circuit and erratic behavior.ADJ Dotz TPar COB LED Par Wash System Instructions  & troubleshooting 4
Special Note: Line Termination. When longer runs of cable are used, you may need to use a terminator on the last unit to avoid erratic behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable terminator (ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior.ADJ Dotz TPar COB LED Par Wash System Instructions  & troubleshooting 5
5-Pin XLR DMX Connectors.
Some manufactures use 5-pin XLR connectors for DATA transmission in place of 3-pin. 5-pin XLR fixtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be used, these adaptors are readily available at most electric stores. The chart below details a proper cable conversion.

3-Pin XLR to 5-Pin XLR Conversion
Conductor 3-Pin XLR Female (Out) 5-Pin XLR Male (In)
Ground/Shield Pin 1 Pin 1
Data Compliment (- signal) Pin 2 Pin 2
Data True (+ signal) Pin 3 Pin 3
Not Used Do Not Use
Not Used Do Not Use

System Menu

Built-In Programs

 

STATIC COLOR CL:RGB Flash00-99

Blackout,

Red-Green-Blue-Yellow-Cyan-Purple-White Flash speed adjustable.

DREAM

Speed00-99 Flash00-99

Seven color dreaming

Speed & Flash adjustable

METEOR

Speed00-99 Flash00-99

Seven color flow

Speed & Flash adjustable

FADE

Speed00-99 Flash00-99

Seven color fade

Speed & Flash adjustable

CHANGE

Speed00-99 Flash00-99

Seven color change

Speed & Flash adjustable

FLOW 1

Speed00-99 Flash00-99

Seven color chase

Speed & Flash adjustable

FLOW 2

Speed00-99 Flash00-99

Seven color chase

Speed & Flash adjustable

FLOW 3

Speed00-99 Flash00-99

Seven color chase

Speed & Flash adjustable

FLOW 4

Speed00-99 Flash00-99

Seven color chase

Speed & Flash adjustable

FLOW 5

Speed00-99 Flash00-99

Seven color chase

Speed & Flash adjustable

FLOW 6

Speed00-99 Flash00-99

Seven color chase

Speed & Flash adjustable

FLOW 7

Speed00-99 Flash00-99

Seven color chase

Speed & Flash adjustable

FLOW 8

Speed00-99 Flash00-99 C1: RGB       C2:RGB

Seven color chase

Speed & Flash adjustable

FLOW 9

Speed00-99 Flash00-99 C1:RGB         C2:RGB

Seven color chase

Speed & Flash adjustable

The LCD backlight will shut off after 30 seconds, to relight the background, press the MODE button for 5 seconds. DMX Mode – Set the DMX Address and DMX Channel Mode –

  1.  Press the MENU button until “DMX Mode” and underneath “ADDR: XXX” and “CH:XX” is displayed, press ENTER.
  2.  “XXX” will now begin to flash, use the UP and DOWN buttons to find your desired DMX address, then press ENTER.
  3.  “XX” will now begin to flash, use the UP and DOWN buttons to find your desired DMX Channel mode, then press ENTER.
    Secondary Mode – This will let you set your unit as a secondary unit in a primary/secondary configuration.
    1. Press the MENU button until “Secondry Mode” is displayed.

Your unit will now follow the Primary. Sound Mode – In this mode the unit will run in sound active mode.

  1.  Press the MENU button until “Sound Mode” is displayed.
  2.  Press ENTER to adjust your sound sensitivity. When you press ENTER the number next to “Sens” will begin to flash, use the UP and DOWN buttons to adjust the sound sensitivity. Once you ound your desired sensitivity press ENTER to confirm.
  3.  When you press ENTER the number next to “FQN” will begin to flash, use the UP and DOWN buttons to adjust the amount of times you would like the program to cycle before changing to the next program. Press ENTER to confirm.

Auto Run –

  1. Press the MENU button until “Auto Run” is displayed, and “FQN:XX” will be displayed underneath. “XX” representing the the number displayed.
  2. Press ENTER and the number will begin to flash, use the UP and DOWN buttons to adjust the amount of times you would like the program to cycle before changing to the next program. Press ENTER to confirm.

Built-In Programs – See the chart on page 7 to find your desired program. Built-In Programs will not be dis- played, one of the programs listed on page 7 will.

  1.  Press the MENU button until one of the Programs on page 7 is displayed. The displayed program depends on the last pro-gram you had set the unit to.
  2.  Press ENTER to move through the various adjustments of each program, and use the UP and DOWN button to make adjust-ments.

Dim Curve – This setting will let you select your desired dimming curve. 

  1.  Press the MENU button until “Dim Curve” is displayed, press ENTER.
  2.  1 of 5 dimming curve settings will be displayed: Standard, Stage, TV, Architectural, or Theatre. Use the UP and DOWM but-tons to select your desired dimming curve and press ENTER to confirm..

Pixel Flip – In this mode you adjust the unit so that the LEDs in DMX mode will illuminate at your desired starting point. The unit can start at either the left or the right.

  1.  Press the MENU button until “Pixel Flip” is displayed, press ENTER.
  2.  Either “Off” or “On” will be displayed. “Off” the unit will illumi-nate left to right, and “On” the unit will illuminate right to left. Use the UP and DOWN buttons to find your desired mode, and press ENTER.

RF Active – This menu will let you activate the RF remote control. 

  1.  Press the MENU button until “RF Active” is displayed, press ENTER.
  2.  Either “On” or “Off” will be displayed, use the UP or DOWN buttons to activate (On) or deactivate (Off) the remote. Press ENTER to confirm.

Universal DMX Control

Universal DMX Control: This function allows you to use a Elation® universal DMX-512 controller to control the chases and patterns, dimmer and strobe. A DMX controller allows you to create unique programs tailored to your individual needs. The Dotz TPar System has 5 DMX channel modes; a 3 Channel Mode, 5 Channel Mode, 9 Channel Mode, 12 Channel Mode, & 18 Channel Mode. See pages 14-20 for the DMX channel modes and traits.

  1.  This function will allow you to control each individual fixture’s traits with a standard DMX 512 controller such as the Elation® Show Designer™ or the Elation® DMX Operator.™
  2.  To run your fixture in DMX mode, follow directions on page 8 to set your DMX address and DMX Channel mode.
  3.  Plug in the fixture via the XLR connections to any standard DMX
  4.  For longer cable runs (more than a 100 feet) use a terminator on the last fixture.

Primary-Secondary Configuration

Primary/Secondary Operation: This function will allow you to link up to 16 units together and operate without a controller. The units will be sound activated. In Primary-Secondary operation one unit will act as the controlling unit and the others will react to the controlling units programs. Any unit can act as a Primary or as a Secondary.

  1.  Using approved DMX data cables, daisy chain your units together tor at the last fixture.
  2. On the Primary unit, designate the unit as a “Primary” unit following the instructions on page 10. Then set your desired operating mode.3. On the secondary units press the MODE button until “Secondary Mode” is displayed.4.The Secondary units will now follow the Primary unit.

Foot Controller

The Foot Controller has 4 different functions. To control your fix-ture you must connect the foot controller using the provided cable. Set the Dotz TPar System to its “Secondary” setting. Connect one end of the cable to the foot controller and the other end to the rear of the Dotz TPar System bar. To activate the Foot Controller press any pedal once. To deactivate the Foot Controller press the Blackout and Program pedals at the same time.
BLACKOUT – Pressing this button will blackout the fixture. Press the pedal for more then 3 seconds to activate Full On.
MODE – This pedal selects and activates the 3 different operating modes. Press the pedal for more then 3 seconds to activate Full On.

  • Press the MODE pedal and the Red LED lights up, you are Static Color mode. Use the UP and DOWN pedals to scroll through the 7 different colors.
  • Press the MODE pedal and the Green LED lights up, you are in Sound Active mode. Adjust the sound sensitivity using the knob on the rear panel of the foot controller.
  • Press the MODE pedal and the Yellow LED lights up, you are in the Built-In Programs mode. Use the UP and DOWN pedals to scroll through the 14 different programs. Refer to the chart on page 7 for the programs.

UP – This pedal works in conjunction with the MODE pedal, it lets you scroll through the static colors and built-in programs. Press the UP pedal for more then 3 seconds to activate connected light 1 (right side of the bar). Press the pedal for more then 3 seconds to deacti-vate light 1.
DOWN – This pedal works in conjunction with the MODE pedal, it lets you scroll through the static colors and built-in programs. Press the DOWN pedal for more then 3 seconds to activate connected light 2 (left side of the bar). Press the pedal for more then 3 seconds to de-activate light 2.
ADJ Products, LLC – www.adj.com – Dotz TPar System User Manual Page 12

Dotz RF Remote

  • The Dotz RF remote has many different functions and allows you to control your Dotz TPar System from long distance. The remote can control your system up to 25 meters. To use the remote
  • you must first activate the fixtures receiver, to activate the receiver please see the instructions on page 11.
  • BLACKOUT – Pressing this button will blackout the fixture.
  • FADE – This button will activate the color fade program.
  • COLOR – This button will activate the static color mode. Use the “+” and “-” buttons to scroll through the colors and find your desired color.
  • PROGRAMS – This button will activate the built-in programs mode. Use the “+” and “-” buttons to scroll through programs 2-14 to find your desired program.
  • LIGHT 1 ON – This button will activate any light that is installed on the top of the bar and connected to the first light connection (right side of the bar).
  • LIGHT 1 OFF – This button will deactivate any light that is installed on the top of the bar and connected to the first light connection (right side of the bar).
  • LIGHT 2 ON – This button will activate any light that is installed on the top of the bar and connected to the second light connection (left side of the bar).
  • LIGHT 2 OFF – This button will deactivate any light that is installed on the top of the bar and connected to the second light connection (left side of the bar).
  • SOUND ACTIVE – This button activates sound active mode.
  • AUTO RUN – This button will run an automatic program. Use the “+” and “-” buttons to adjust the speed of the auto run.
  • “+” and “-” – Use these buttons to adjust the speed of the Auto Run, scroll through the built-in programs, and scroll through the static col-ors.
  • ADJ Products, LLC – www.adj.com – Dotz TPar System User Manual Page 13
  • When Channel 13 is being used between the values of 16-135, Channel 14 will control the dimming.
  • When Channel 13 is being used between the values of 136-239, Channel 14 will control the speed of the programs.
  • When Channel 13 is being used between the values of 240-255, Channel 14 will control sound sensitivity.
  • If extra lights are attached to the top of the bar, Channels 17 & 18 will control the lights.

 

Dotz TPar System                                   3 Channel Mode
Channel Value Function
1  

0 – 255

RED

0% – 100%

2  

0 – 255

GREEN

0% – 100%

3  

0 – 255

BLUE

0% – 100%

 

Dotz TPar System                                   5 Channel Mode
Channel Value Function
1  

0 – 255

RED

0% – 100%

2  

0 – 255

GREEN

0% – 100%

3  

0 – 255

BLUE

0% – 100%

4  

0 – 127

128 – 255

LIGHT 1 (Installed on top of the bar) OFF

ON

5  

0 – 127

128 – 255

LIGHT 2 (Installed on top of the bar) OFF

ON

 

Dotz TPar System                                   9 Channel Mode
Channel Value Function
1  

0 – 255

RED

0% – 100%

2  

0 – 255

GREEN

0% – 100%

3  

0 – 255

BLUE

0% – 100%

4  

0 – 15

16 – 23

24 – 31

32 – 39

40 – 47

48 – 55

56 – 63

64 – 71

72 – 79

80 – 87

88 – 95

96 – 103

104 – 111

112 – 119

120 – 127

128 – 135

136 – 143

144 – 151

152 – 159

160 – 167

168 – 175

176 – 183

184 – 191

192 – 199

200 – 207

208 – 215

216 – 223

COLOR MACROS & PROGRAMS NO FUNCTION

RED GREEN BLUE

RED & GREEN GREEN & BLUE RED & BLUE

RED, GREEN, & BLUE COLOR 1

COLOR 2

COLOR 3

COLOR 4

COLOR 5

COLOR 6

COLOR 7

COLOR 8

COLOR FADE 1 COLOR SNAKE COLOR FADE 2 COLOR CHANGE COLOR FLOW 1

COLOR FLOW 2

COLOR FLOW 3

COLOR FLOW 4

COLOR FLOW 5

COLOR FLOW 6

COLOR FLOW 7

Dotz TPar System                                   9 Channel Mode
Channel Value Function
4  

224 – 231

232 – 239

240 – 255

COLOR MACROS & PROGRAMS

COLOR FLOW 8

COLOR FLOW 9 SOUND ACTIVE

5  

0 – 255

0 – 255

0 – 255

MASTER DIMMER/PROGRAM SPEED/

SOUND SENSITIVITY MASTER DIMMER 0% – 100% PROGRAM SPEED SLOW – FAST

SOUND SENSITIVITY LEAST – MOST

6  

0 – 255

STROBING

SLOW – FAST

7  

0 – 41

42 – 84

85 – 127

128 – 170

171 – 213

214 – 255

DIMMER CURVES STANDARD STAGE

TV        ARCHITECTURAL THEATER

DEFAULT TO UNIT CURVE SETTING

8  

0 – 127

128 – 255

LIGHT 1 (IF APPICABLE)

LIGHT 1 OFF

LIGHT 1 ON

9  

0 – 127

128 – 255

LIGHT 2 (IF APPICABLE) LIGHT 2 OFF

LIGHT 2 ON

Dotz TPar System                                 12 Channel Mode
Channel Value Function
1  

0 – 255

RED 1

0% – 100%

2  

0 – 255

GREEN 1

0% – 100%

3  

0 – 255

BLUE 1

0% – 100%

4  

0 – 255

RED 2

0% – 100%

5  

0 – 255

GREEN 2

0% – 100%

6  

0 – 255

BLUE 2

0% – 100%

7  

0 – 255

RED 3

0% – 100%

8  

0 – 255

GREEN 3

0% – 100%

9  

0 – 255

BLUE 3

0% – 100%

10  

0 – 255

RED 4

0% – 100%

11  

0 – 255

GREEN 4

0% – 100%

12  

0 – 255

BLUE 4

0% – 100%

Dotz TPar System                                 18 Channel Mode
Channel Value Function
1  

0 – 255

RED 1

0% – 100%

2  

0 – 255

GREEN 1

0% – 100%

3  

0 – 255

BLUE 1

0% – 100%

4  

0 – 255

RED 2

0% – 100%

5  

0 – 255

GREEN 2

0% – 100%

6  

0 – 255

BLUE 2

0% – 100%

7  

0 – 255

RED 3

0% – 100%

8  

0 – 255

GREEN 3

0% – 100%

9  

0 – 255

BLUE 3

0% – 100%

10  

0 – 255

RED 4

0% – 100%

11  

0 – 255

GREEN 4

0% – 100%

12  

0 – 255

BLUE 4

0% – 100%

13  

0 – 15

16 – 23

24 – 31

32 – 39

40 – 47

48 – 55

56 – 63

64 – 71

72 – 79

COLOR MACROS & PROGRAMS NO FUNCTION

RED GREEN BLUE

RED & GREEN GREEN & BLUE RED & BLUE

RED, GREEN, & BLUE COLOR 1

Dotz TPar System                                 18 Channel Mode
Channel Value Function
13  

80 – 87

88 – 95

96 – 103

104 – 111

112 – 119

120 – 127

128 – 135

136 – 143

144 – 151

152 – 159

160 – 167

168 – 175

176 – 183

184 – 191

192 – 199

200 – 207

208 – 215

216 – 223

216 – 223

224 – 231

232 – 239

240 – 255

COLOR MACROS & PROGRAMS

COLOR 2

COLOR 3

COLOR 4

COLOR 5

COLOR 6

COLOR 7

COLOR 8

COLOR FADE 1 COLOR SNAKE COLOR FADE 2 COLOR CHANGE COLOR FLOW 1

COLOR FLOW 2

COLOR FLOW 3

COLOR FLOW 4

COLOR FLOW 5

COLOR FLOW 6

COLOR FLOW 7

COLOR FLOW 7

COLOR FLOW 8

COLOR FLOW 9 SOUND ACTIVE

14  

0 – 255

0 – 255

0 – 255

MASTER DIMMER/PROGRAM SPEED/

SOUND SENSITIVITY MASTER DIMMER 0% – 100% PROGRAM SPEED SLOW – FAST

SOUND SENSITIVITY LEAST – MOST

15  

0 – 255

STROBING

SLOW – FAST

16  

0 – 41

42 – 84

85 – 127

DIMMER CURVES STANDARD STAGE

TV

Dotz TPar System 18 Channel Mode
Channel Value Function
16 DIMMER CURVES
128 – 170 ARCHITECTURAL
171 – 213 THEATER
214 – 255 DEFAULT TO UNIT CURVE SETTING
17 LIGHT 1 (IF APPICABLE)
0 – 127 LIGHT 1 OFF
128 – 255 LIGHT 1 ON
18 LIGHT 2 (IF APPICABLE)
0 – 127 LIGHT 2 OFF
128 – 255 LIGHT 2 ON

PhotometricsADJ Dotz TPar COB LED Par Wash System Instructions  & troubleshooting 6

Power Cord Daisy Chaining

With this feature you can connect the fixtures to one another using the IEC input and output sockets. The quantity that can be connected is 7 fixtures maximum for 120V, and 14 fixtures maxi-mum for 230V. After the maximum fixtures has been reached you will need to use a new power outlet. They must be the same fix-tures. DO NOT mix fixtures. ADJ Products, LLC – www.adj.com – Dotz TPar System User Manual Page 21

Alternate Lighting Installation

A special feature that this system has is that you are able to mount two light effects on top of the “T” bar. You are then able to power those lights by plugging the power cords directly into the bar. The power sockets are located on the right side and left side. The middle power socket is for power cord daisy chaining. Do not use the middle power socket to power your added lights.
To add the lights onto the top is a simple process. Make sure your “T” bar is set up on the stand correctly and is secure. Follow the instruc-tions below.

  1.  Start by unscrewing the black knob that is attached to the bolt.
  2.  Attach the lighting effect to the bolt using the lighting effects con-nected bracket.
  3.  After you have set the bracket onto the bolt, screw the black knob and secure the knob tightly. See the sample pictures below.
  4.  Plug the mounted lights into their respective power jacks.ADJ Dotz TPar COB LED Par Wash System Instructions  & troubleshooting 7

Fuse Replacement

Locate and remove the unit’s power cord. Once the cord has been removed located the fuse holder located inside the power socket. Insert a flat-head screw driver into the power socket and gently pry out the fuse holder. Remove the bad fuse and replace with a new one. The fuse holder has a built-in socket for a spare fuse be sure not to confuse the spare fuse with active fuse.

Cleaning

Due to fog residue, smoke, and dust cleaning the internal and exter-nal optical lenses must be carried out periodically to optimize light output.

  1. Use a soft cloth to wipe down the outside casing. Cleaning frequency depends on the environment in which the fixture operates (i.e. smoke, fog residue, dust, dew).

Troubleshooting

Listed below are a few common problems the user may encounter, with solutions.

Unit not responding to DMX:

  1.  Check that the DMX cables are connected properly and are wired correctly (pin 3 is “hot”; on some other DMX devices pin 2 may be ‘hot’). Also, check that all cables are connected to the right connectors; it does matter which way the inputs and outputs are connected.

Unit does not respond to sound:

  1. Quiet or high pitched sounds will not activate the unit. If problems are not resolved; Contact ADJ Products, LLC for service. 1-800-322-6337

Warranty

MANUFACTURER’S LIMITED WARRANTY

  •  ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable evidence, at the time service is sought.
  • For warranty service you must obtain a Return Authorization number (RA#) before sending back the product–please contact ADJ Products, LLC Service Department at 800-322-6337. Send the pro- duct only to the ADJ Products, LLC factory. All shipping charges must be pre-paid. If the requested repairs or service (including parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return shipping charges only to a designated point within the United States. If the entire instru- ment is sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for loss of or damage to any such accessories, nor for the safe return thereof.
  • This warranty is void if the serial number has been altered or removed; if the product is modified in any manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because not properly maintained as set forth in the instruction manual.
  • This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August 15, 2012, and bear indentifying marks to that effect.
  •  ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products without any obligation to include these changes in any products theretofore manufactured. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above. Except to the extent prohibited by applicable law, all implied warranties mad by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness, are limited in duration to the warranty period set forth above. And no warranties, whether expressed or implied, including warranties of merchantability or fitness, shall apply to this product after said period has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or damage, direct or consequential, arising out of the use of, or inability to use, this product. This warranty is the only written warranty applicable to ADJ Products, LLC Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published.

MANUFACTURER’S LIMITED WARRANTY PERIODS:

  • Lighting Products = 1-year (365 days) Limited Warranty (Such as: Special Effect Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands etc. excluding LED and lamps)
  • Laser Products = 90-Day Limited Warranty
  • L.E.D. Products = 2-year (730 days) Limited Warranty (excluding motors, PCB boards, and power supplies, which have a 1-year (365 day Limited Warranty) and batteries which have a 180 day limited warranty).

Specifications

  • SPECIFICATIONS: Voltage: 100V~240V 50Hz/60Hz
  • LEDs: Each Par contains a 30W COB TRI LED
  • Power Consumption:
  • 144W Total (All LED’s @ Full)
  • Beam Angle:
  • 90 Degr
  • ees
  • Includes 25 Degr
  • ee Lens
  • Fuse:
  • 3Amp (120V)
  • 2Amp (240V)
  • Power Cor
  • d Daisy Chain: 4 Fixtures Max. (120V)
  • 9 Fixtur
  • es Max. (230V)
  • weight: 35lbs./ 16Kgs.
  • Dimensions: 39.5” (L) x 12.75” (W) x 3.25” (H)
  • 1000 x 320 x 82mm
  • Colors: RGB Color Mixing
  • DMX Channels: 3 Channel Mode, 5 Channel Mode,
  • 9 Channel Mode, 12 Channel Mode, & 18 Channel
  • Mode
  • working Position: Any safe working position
  • warranty: 2 Year (730 days)Auto Sensing Voltage: This fixture contains a automatic volt-age switch, which will auto sense the voltage when it is plugged into the power source.Please Note:
  • Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice.
  • Dotz TPar SystemSpecifications
  • ADJ Products, LLC
  • 6122 S. Eastern Ave. Los Angeles, CA 90040 USA
  • Tel: 323-582-2650 / Fax: 323-725-6100
  • Web: www.adj.com / E-mail: [email protected]
  • A.D.J. Supply Europe B.V.
  • Junostraat 2
  • 6468 EW Kerkrade
  • Netherlands
  • [email protected]/ www.adj.eu
  • Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99
  • ADJ Products, LLC – www.adj.com – Dotz TPar System User Manual Page 26
  • Approvals / Ratings: CE Certified

FAQ


Setting up ADJ Dotz TPar COB LED Par Wash System Instructions is easy with these step-by-step instructions. Follow the steps are you are set-up in no time.

Using ADJ Dotz TPar COB LED Par Wash System Instructions is simple by using this manual. Follow the instructions one by one and everything will be fine

Is ADJ Dotz TPar COB LED Par Wash System Instructions stuck or not working properly? By resetting it you can set it back to the standard settings and everything should be back to normal. This works in many cases when problems arise.

This page contains the complete user instructions & manual for ADJ Dotz TPar COB LED Par Wash System Instructions

All symbols, colors and codes for ADJ Dotz TPar COB LED Par Wash System Instructions are explained in this instruction manual. You can find everything you need and moree