AUKEY Bluetooth® Earbuds User Manual

AUKEY Bluetooth® Earbuds User Manual  & troubleshooting 0

User Manual
Bluetooth® Earbuds

Thank you for purchasing the AUKEY EP-B80 Bluetooth® Earbuds. Please read this user manual carefully and keep it for future reference. If you need any assistance, please contact our support team with your product model number and Amazon order number.

Package Contents

Bluetooth® Earbuds                                       Carrying Pouch
USB-A to C Cable                                           User Manual
Three Pairs of Silicone Ear-Tips (S/M/L)       Warranty Card
Three Pairs of Foam Ear-Tips (S/M/L)

Specifications
Model EP-B80
Technology Bluetooth 5.0+EDR, A2DP, AVRCP, HFP, HSP, aptX, aptX-LL, AAC
Chipset QCC3005
Driver (each channel) 1 × 10mm / 0.4” Dynamic Driver and Balanced Armature
Sensitivity 95dB ±3dB (at 1kHz)
Frequency Range 10Hz – 40kHz
Impedance 32 ohm ±15%
Microphone Type MEMS (microphone chip)
Microphone Sensitivity -42dB ±3dB
Input DC 5V
Charging Time 1.5 hours
Battery Life Up to 8 hours
Battery Type Li-Polymer (2 x 60mAh)
Operating Range Up to 15m / 49ft
Weight 15g / 0.52oz

– 01 –

Product Diagram

AUKEY Bluetooth® Earbuds User Manual  & troubleshooting 1

– 02 –

Getting Started

Charging
Fully charge your earbuds before first use. Before charging, make sure the earbuds are turned off. To charge, simply connect one end of the USB-A to C cable to a USB charging port and the other end to the input port on the earbuds. When the green LED indicator light turns off, your earbuds are fully charged and ready for use. Charging takes around 1.5 hours.

AUKEY Bluetooth® Earbuds User Manual  & troubleshooting 2

Turning On / Off
Turn On Press and hold the multi-function button. The LED indicator will light up white for 2 seconds and you’ll hear an ascending tone
Turn Off Press and hold the multi-function button. The LED indicator will light up green for 2 seconds and you’ll hear a descending tone

– 03 –

Pairing

Starting with the earbuds powered off:

  1. Press and hold the multi-function button until the LED indicator flashes green and white alternately
  2. Turn on Bluetooth on the device you want to pair with the earbuds
  3. In the list of available devices, find and select “AUKEY EP-B80”
  4. If a code or PIN is required for pairing, enter “0000”

Notes

  • To clear the pairing list, power on the earbuds and then hold volume + and volume – simultaneously for 5 seconds until the LED indicator lights up green and white. Once the pairing list is cleared, you’ll hear a tone and the earbuds will automatically enter pairing mode
  • The earbuds will automatically shut down after 5 minutes in pairing mode if no devices are paired
  • If your paired device is turned off or manually disconnected, the earbuds LED indicator will flash white twice every 5 seconds and the earbuds will shut down after 5 minutes
  • Double-press the multi-function button after turning off Bluetooth on a connected device to enter pairing mode. The LED indicator will flash white and green alternately for 3 minutes. If no devices are paired, the earbuds will enter standby mode
  • The maximum wireless operating range is 15m (49ft). If you exceed this range, the earbuds will disconnect from your paired device and you’ll hear a tone. The connection will be re-established once you re-enter the wireless range within 5 minutes. The earbuds will automatically reconnect to the last-paired device. To connect with other devices, repeat the previous “Pairing” steps

– 04 –

Music and Calls Control

Streaming Audio
Once paired, you can wirelessly stream audio from your device to your earbuds. Music will automatically pause when you receive an incoming phone call, and resume once the call has ended.

Play or pause Press the multi-function button once
Adjust volume Press volume + or –
Skip to next / previous track Press and hold the volume + / – for 2 seconds

Making Calls
Once paired with your smartphone, making and answering calls can be managed via the in-line remote.

Answer or end a call Short-press the multi-function button. If there’s a second incoming call, press the multi-function button once to answer the second call and end the first call. Alternatively, press and hold the multi-function button for 2 seconds to answer the second call and put the first call on hold. Then press and hold the multi-function button for 2 seconds to switch between these two calls
Redial last-called number Double-press the multi-function button when your device is connected (but not playing music)
Reject an incoming call Double-press the multi-function button
Switch mic During a call, press and hold the volume + for 2 seconds to switch between the earbuds and your phone for talking
Use Siri or other voice assistants When your device is connected, press and hold the multi-function button for 2 seconds and you’ll hear a tone

– 05 –

LED Indicator

Status

White & green flashing alternately Pairing mode
White flashing twice every 5 seconds Standby mode / Disconnected
White flashing once every 5 seconds Connected / Playing music
White flashing once every second In call
Green flashing twice every 5 seconds Low battery
Green Charging
Green off (after charging) Fully charged
FAQ

The earbuds are on but not connecting to my device
For the earbuds and your device to establish a connection, you need to put them both in pairing mode. Please follow the instructions in the “Pairing” section of this manual.

I’ve established a connection with my smartphone but can’t hear any sound
Double-check the volume level on your smartphone and the earbuds. Some smartphones require you to set up the earbuds as an audio output device before the audio can be transmitted. If you’re using a music player or other device, please make sure it supports the A2DP stereo music profile.

The sound isn’t very clear or the caller can’t hear my voice clearly
Adjust the volume on your smartphone and the earbuds. Try getting closer to your smartphone to rule out the possibility of interference or wireless range-related issues.

What is the wireless range of the earbuds?

– 06 –

The maximum range is 15m (49ft). However, the actual range will depend on environmental factors. For optimal performance, keep your devices connected with the earbuds within a 15ft­40ft range and make sure that there are no major obstacles (like reinforced steel walls) between the earbuds and your devices.

My earbuds won’t turn on
Try charging the earbuds for a while. If the earbuds still won’t power on, please contact our support team at the address below.

Product Care & Use
  • Keep away from liquids and extreme heat
  • Don’t use the earbuds at high volume for extended periods, as this may cause permanent hearing damage or loss
Warranty & Customer Support

For questions, support, or warranty claims, contact us at the address below that corresponds with your region. Please include your Amazon order number and product model number.

Amazon US orders: [email protected]
Amazon EU orders: [email protected]
Amazon CA orders: [email protected]
Amazon JP orders: [email protected]
Amazon AU orders: [email protected]

*Please note, AUKEY can only provide after sales service for products purchased directly from AUKEY. If you have purchased from a different seller, please contact them directly for service or warranty issues.

– 07 –

Notice for the US

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC Rules

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference.
  2. This device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.

IC Statement

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.
CE Statement

Max RF power level:
BT classic (2402­2480MHz): 2.1dBm
RF exposure assessment has been performed to prove that this unit will not generate the harmful EM emission above the reference level as specified in EC Council Recommendation (1999/519/EC).

– 09 –

CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

Excessive sound pressure from earphones and headphones can cause hearing loss.

AUKEY Bluetooth® Earbuds User Manual  & troubleshooting 3

Hereby, Shenzhen AUKEY E Business Co., Ltd. declares that the radio equipment type (Bluetooth® Headphones, EP-B80) is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.aukey.com.

AUKEY Bluetooth® Earbuds User Manual  & troubleshooting 4

Notice: This device may be used in each member state of the EU.

Trademark

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Shenzhen AUKEY E Business Co., Ltd. is under license. Other trademarks and trade names are those of their respective owners.

– 10 –

AUKEY Bluetooth® Earbuds User Manual  & troubleshooting 5

Qualcomm® aptX™ is a product of Qualcomm Technologies International, Ltd. Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other countries, used with permission. aptX is a trademark of Qualcomm Technologies International, Ltd., registered in the United States and other countries, used with permission.

– 11 –

Model: EP-B80

Shenzhen AUKEY E Business Co., Ltd.
www.aukey.com | [email protected]
No.102, Building P09, Electronics Trade Center
Huanan City, Pinghu Town, Longgang District
Shenzhen, Guangdong, 518111, CN

FCC ID: 2AFHP-EPB80

AUKEY Bluetooth® Earbuds User Manual  & troubleshooting 6    AUKEY Bluetooth® Earbuds User Manual  & troubleshooting 7   AUKEY Bluetooth® Earbuds User Manual  & troubleshooting 8  AUKEY Bluetooth® Earbuds User Manual  & troubleshooting 9

References

FAQ


Setting up AUKEY Bluetooth® Earbuds User Manual is easy with these step-by-step instructions. Follow the steps are you are set-up in no time.

Using AUKEY Bluetooth® Earbuds User Manual is simple by using this manual. Follow the instructions one by one and everything will be fine

Is AUKEY Bluetooth® Earbuds User Manual stuck or not working properly? By resetting it you can set it back to the standard settings and everything should be back to normal. This works in many cases when problems arise.

This page contains the complete user instructions & manual for AUKEY Bluetooth® Earbuds User Manual

All symbols, colors and codes for AUKEY Bluetooth® Earbuds User Manual are explained in this instruction manual. You can find everything you need and moree