BFT Mitto 2M 4M Remote Coding Instructions

BFT Mitto 2M 4M Remote Coding Instructions & troubleshooting

BFT Mitto 2M 4M Remote Coding Instructions
BFT Mitto 2M 4M Remote Coding Instructions  & troubleshooting 1

Programming of your new remote control – overview

There are many different types of receivers, so coding varies based on the type of receiver that you have. To simply put it, if your receiver has a digital screen, use option 2. If your receiver does not have a digital screen, use option 1.

Receiver without digital screen (first type of receiver):

BFT Mitto 2M 4M Remote Coding Instructions  & troubleshooting 2

  1. Open your motor, and try and find the receiver. If your receiver is in a case, then remove the casing. You are trying to find something that looks like a control board
  2. If you wish the transmitter to activate output 1, press push button SW1, otherwise press push button SW2 to activate output 2. The LED light on receiver will start to flash
    BFT Mitto 2M 4M Remote Coding Instructions  & troubleshooting 3
  3. Press and release the number “3” and the number “4” button on your new remote control at the same time. The will cause the LED to stop flashing, and remain illuminated
  4. Press BFT Mitto 2M 4M Remote Coding Instructions  & troubleshooting 4and release the number any button on your new remote control that you want to use to control your garage/gate. This will cause the LED to flash fast. This indicates that that button on your new remote has been coded. After about 1 second, the LED will continue flashing, but will be flashing slowly.
    BFT Mitto 2M 4M Remote Coding Instructions  & troubleshooting 5
  5. If you would like to code in additional remotes, this is the time to do it. You will need to start again using the additional remote and complete steps 3 & 4 for each additional remote. Whether you code additional remotes or not, once you  have finished coding your remote(s), the LED should be flashing slowly.
  6. Wait 15 seconds
  7.  Your new remote control/controls are now programmed

Receiver with digital screen (second type of receiver):

  1. Press the “OK” button on your receiver twice. The screen displays “PARA.”
  2. Press the “-“ button on your receiver twice. The screen displays “RADIO.”
  3. Press the “OK” button on your receiver once. The screen displays “ADJ STRT.”
  4. Press the “OK” button on your receiver once. The screen displays “Hidden Button.”
  5. Press the number “3” and the number “4” button on your new remote control at the same time. Keep them pressed down.
  6. Keep holding the buttons down until the screen displays “released”. Let the buttons go. The screen displays “Desired Button”.
  7. Press and release the button on your new remote control that you want to use to control your gate/garage. The screen displays “OK”.
  8. If you would like to program an additional remote: When “ADJ STRT” appears, press “OK” to code an additional remote, and follow the instructions displayed.
  9. After coding the remote(s), wait about 30 seconds. Now you remote is coded.
    BFT Mitto 2M 4M Remote Coding Instructions  & troubleshooting 6

Warning

BFT Mitto 2M 4M Remote Coding Instructions  & troubleshooting 7 To prevent possible SERIOUS INJURY or DEATH:

  • Battery is hazardous:NEVER allow children near batteries.
  • If battery is swallowed, immediately notify a doctor. To reduce risk of fire, explosion or chemical burn: – Replace ONLY with the same size and type battery
  • DO NOT recharge, disassemble, heat above 100° C or incinerate Battery will cause SEVERE or FATAL injuries in 2 hours or less if swallowed or placed inside any part of the body.

 

FAQ


Setting up BFT Mitto 2M 4M Remote Coding Instructions is easy with these step-by-step instructions. Follow the steps are you are set-up in no time.

Using BFT Mitto 2M 4M Remote Coding Instructions is simple by using this manual. Follow the instructions one by one and everything will be fine

Is BFT Mitto 2M 4M Remote Coding Instructions stuck or not working properly? By resetting it you can set it back to the standard settings and everything should be back to normal. This works in many cases when problems arise.

This page contains the complete user instructions & manual for BFT Mitto 2M 4M Remote Coding Instructions

All symbols, colors and codes for BFT Mitto 2M 4M Remote Coding Instructions are explained in this instruction manual. You can find everything you need and moree