BOSS DD-BT Digital Delay Owner’s Manual

BOSS DD-BT Digital Delay Owner’s Manual & troubleshooting

BOSS DD-BT Digital Delay Owner’s Manual  & troubleshooting 1

BOSS DD-BT Digital Delay Owner’s Manual

BOSS DD-BT Digital Delay Owner’s Manual  & troubleshooting 2

 

BOSS DD-BT Digital Delay Owner’s Manual  & troubleshooting 3

Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet). After reading, keep the document(s) where it will be available for immediate reference.

 

Panel Descriptions

BOSS DD-BT Digital Delay Owner’s Manual  & troubleshooting 4

BOSS DD-BT Digital Delay Owner’s Manual  & troubleshooting 5

 

Precautions When Connecting

  • To prevent malfunction and equipment failure, always turn down the volume, and turn off all the units before making any connections.
  • Do not use connection cables that contain a built-in resistor.
  • Once everything is properly connected, be sure to follow the procedure below to turn on their power. If you turn on equipment in the wrong order, you risk causing malfunction or equipment failure.

When powering up
Turn on the power to your guitar amp last.

When powering down
Turn off the power to your guitar amp first.

  • Before turning the unit on/off, always be sure to turn the volume down. Even with the volume turned down, you might hear some sound when switching the unit on/off. However, this is normal and does not indicate a malfunction.

 

About Output

  • Connect to the OUTPUT jack only
    The direct sound + delay sound is output.

BOSS DD-BT Digital Delay Owner’s Manual  & troubleshooting 6

  • Connect to the OUTPUT jack and the DIRECT OUT jack
    The delay sound is output from the OUTPUT jack, and the direct sound is output from the DIRECT OUT jack.

BOSS DD-BT Digital Delay Owner’s Manual  & troubleshooting 7

  • Connect to the SEND/RETURN jacks of a guitar amplifier
    If you’re using this unit in a parallel-connected effect loop, insert a dummy plug into the DIRECT OUT jack so that only the delay sound is output to the RETURN jack.

BOSS DD-BT Digital Delay Owner’s Manual  & troubleshooting 8

 

Using the Tempo Delay

By pressing the pedal switch or an external foot switch several times in rhythm with your song, you can set the delay time to match the tempo of the song (tempo delay)

MEMO

  • The delay time range is 133–800 msec (BPM = 75–300).
  • The delay time specified by tempo input is maintained until you operate the [TIME] knob.

Using the pedal switch

* If a foot switch (sold separately) is connected to the TEMPO jack, you can’t use the pedal switch to enter the tempo.

  1. Use the [MODE] knob to specify the note value that will be the basis of the delay time.                                                                                 BOSS DD-BT Digital Delay Owner’s Manual  & troubleshooting 9
  2. Hold down the pedal switch for two seconds or longer.
    The CHECK indicator is lit green, and now you can use the pedal switch to enter the tempo.
    * Tempo entry is not possible if the [MODE] knob is set to “SHORT LOOP.”
  3. Press the pedal switch at quarter-note intervals in synchronization with the tempo of the song.
    According to the tempo that you enter, the delay time is set so that it is the length of the note value that you specified with the [MODE] knob.
    The CHECK indicator blinks at the specified tempo.
  4. To finish inputting the tempo, hold down the pedal switch for two seconds or longer.

Using an external footswitch
Basic operation is the same as when using the pedal switch.

  1. Connect a footswitch (sold separately: FS-5U, FS-6, or FS-7) to the TEMPO jack.
  2. Use the [MODE] knob to specify the note value that will be the basis of the delay time.
  3. Press the footswitch at quarter-note intervals in synchronization with the tempo of the song.
    The delay time is set, and the CHECK indicator blinks at the specified tempo.

For the USA

SUPPLIER’S DECLARATION OF CONFORMITY
Compliance Information Statement

  • Model Name : DD-3T
  • Type of Equipment : Guitar Eects
  • Responsible Party : Roland Corporation U.S.
  • Address :  5100 S. Eastern Avenue Los Angeles, CA 90040-2938
  • Telephone : (323) 890-3700

Changing the Battery

  • Batteries should always be installed or replaced before connecting any other devices. This way, you can prevent malfunction and damage.
  • If you handle batteries improperly, you risk explosion and fluid leakage. Make sure that you carefully observe all of the items related to batteries that are listed in “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet).

BOSS DD-BT Digital Delay Owner’s Manual  & troubleshooting 10

  1. Hold down the pedal and loosen the thumbscrew, then open the pedal upward.
  2. Remove the old battery from the battery housing, and remove the snap cord connected to it.
  3. Connect the snap cord to the new battery, and place the battery inside the battery housing.
    * Be sure to carefully observe the battery’s polarity (+ versus –).
  4. Slip the coil spring onto the spring base on the back of the pedal, and then close the pedal.
    * Carefully avoid getting the snap cord caught in the pedal, coil spring, and battery housing.
  5. Finally, insert the thumbscrew into the guide bush hole and fasten it securely.

 

Main Specification

BOSS DD-3T: Digital Delay

BOSS DD-BT Digital Delay Owner’s Manual  & troubleshooting 11

BOSS DD-BT Digital Delay Owner’s Manual  & troubleshooting 12

  • 0 dBu = 0.775 Vrms
  • This document explains the specifications of the product at the time that the document was issued. For the latest information, refer to the Roland website.

 

Read More About This Manual & Download PDF:

FAQ


Setting up BOSS DD-BT Digital Delay Owner’s Manual is easy with these step-by-step instructions. Follow the steps are you are set-up in no time.

Using BOSS DD-BT Digital Delay Owner’s Manual is simple by using this manual. Follow the instructions one by one and everything will be fine

Is BOSS DD-BT Digital Delay Owner’s Manual stuck or not working properly? By resetting it you can set it back to the standard settings and everything should be back to normal. This works in many cases when problems arise.

This page contains the complete user instructions & manual for BOSS DD-BT Digital Delay Owner’s Manual

All symbols, colors and codes for BOSS DD-BT Digital Delay Owner’s Manual are explained in this instruction manual. You can find everything you need and moree