BRIDGE 11 Max+ Keyboard for 11-Inch iPad Pro
TO TURN ON: Press the power key for one second until the LED flashes green.
TO TURN OFF: Press and hold the power key for three seconds until the LED flashes red.
NOTE: The Brydge 11 MAX+ includes Instant-On'”. which means that reconnecting no longer takes seconds. Once paired. your keyboard will instantly connect to your iPad for up to 4 hours before entering sleep mode without impacting power consumption.
TO PAIR: Press and hold the Bluetooth™ key for three seconds until the LED flashes blue. On your iPad, under Settings> Bluetooth™ select Brydge 11 MAX+. When successfully paired. the blue LED will turn off and your keyboard and trackpad will be active.
Download Brydge Connect from the App Store for the latest firmware updates.
Assistive Touch settings must be off for gestures to work properly. To do this. go to iPad Settings> Accessibility> Touch> AssistiveTouch > OFF
TO INSERT: Place your Brydge on a flat surface and open the case. Place your iPad in the bottom of the case and lean it towards the back. The magnets will snap it into place.
TO REMOVE: Place your Brydge on a flat surface. Use the tabs on either side of the case to release the iPad.
TO CHECK BATTERY LIFE: In Today View. go to the BATTERIES section to check battery life. If not available. swipe left on your Home Screen to show Today View, scroll to the bottom and click edit. Scroll down to Batteries. and click the green ·+· icon to add.
NOTE: If battery life is below 15%, backlit key functionality will be disabled to conserve battery.
TO CHARGE: Insert the charging cable into the keyboard and plug the other end into a power source. A solid red LED indicates the Brydge is charging. When the keyboard is fully charged. the red LED will turn off. A full charge can take up to three hours.
Thank you for purchasing a Brydge product. This product comes with a 1-year limited hardware warranty on the terms and conditions set out in this document and at www.brydge.com/warranty. All Brydge warranties are non-transferrable and are only available to the original end-user of the product. Warranties do not apply to products purchased from online vendors unauthorized to sell Brydge-branded product. If a defect arises during the warranty period, cease using the product and contact Brydge. To obtain warranty service, visit www.brydge.com/support or call +l (435) 604-0481. Brydge, at its sole discretion and option, will (1) repair the product at no charge using new parts or parts that are equivalent to new in performance and reliability, or (2) replace or exchange the product with a product of equivalent functionality and value. Brydge offers free return shipping on any approved warranty claims. A shipping label will be provided to you if you are within the United States. If you are outside the United States. Brydge will reimburse your return shipping to a maximum of US$15.00 after providing a copy of the shipping receipt.
Australia Only: Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Brydge Technologies LLC I 1912 Sidewinder Dr. Suite 104. Park City, UT 84060 USA
Customer Support I +l (435) 604-0481 I [email protected]
HAVE A QUESTION? Visit www.brydge.com/support
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science
and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates. uses. and can radiate radio frequency energy and. if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help.
This wireless keyboard (Brydge 11 MAX+. FCC ID: 2ADRG-BRY403D, IC: 24378-BRY403D) is compatible with the iPad Pro 11-inch (1st generation) (FCC ID:BCGA1980/BGCA2013/BGCA1934, IC: 579C-Al980/579CA2013/579C-Al934). iPad Pro 11-inch (2nd generation) (FCC ID: BCGA2068/BGCA2230, IC: 579C-A2068/579C-A2230). iPad Pro 11-inch (3rd generation) (FCC ID BCGA2377/BGCA2459/BGCA2301/ BGCA2460, IC: 579C-A2377/579C-A2459/579C-A2301/579C-A2460) and iPad Air (4th generation) (FCC ID BCGA2316/BGCA2324/BGCA2325/BGCA2072, IC: 579C-A2316/579C-A2324/579C-A2325/ 579C-A2072).
RF Exposure Information:
FCC RF Exposure requirements: The highest SAR value reported under this standard during product certification for use next to the head with the minimum separation distance of 0mm. This transmitter must not be collocated or operating in conjunction with any other antenna or transmitter.
This product is compliance to FCC RF Exposure requirements and refers to FCC website https://apps.fcc. gov/oetcf/eas/reports/GenericSearch.cfm search for FCC ID: 2ADRG-BRY 403D
This EUT is compliance with SAR for general population/uncontrolled exposure limits in IC RSS-102 and had been tested in accordance with the measurement methods and procedures specified in IEEE 1528 and IEC 62209. This equipment is safe to use next to your body. This device and its antenna(s)must not be colocated or operating in conjunction with any other antenna or transmitter.
© 2021 Brydge. All Rights Reserved.
iPad and Apple are registered trademarks of Apple Inc .. registered in the U.S. and other countries. The Bluetooth word mark, and logos are owned by Bluetooth SIG, Inc. Use of such marks by Brydge is under license. Brydge is a trademark of Brydge Global Pte. Ltd. Other trademarks and tradenames are those of their respective owners.