CANDY Watch Touch Ovens Instruction Manual

CANDY Watch Touch Ovens Instruction Manual & troubleshooting

CANDY Watch Touch Ovens Instruction Manual  & troubleshooting 1

CANDY Watch Touch Ovens

CANDY Watch Touch Ovens Instruction Manual  & troubleshooting 2

General Instructions

We thank you for choosing one of our products. For the best results with your oven, you should read this manual carefully and retain it for future reference. Before installing the oven, take note of the serial number so that you can give it to customer service staff if any repairs are required. Having removed the oven from its packaging, check that it has not been damaged during transportation. If you have doubts, do not use the oven and refer to a qualified technician for advice. Keep all of the packaging material (plastic bags, polystyrene, nails) out of the reach of children. When the oven is switched on for the first time, strong smelling smoke can develop, which is caused by the glue on the insulation panels surrounding the oven heating for the first time. This is absolutely normal and, if it occurs, you should wait for the smoke to dissipate before putting food in the oven. The manufacturer accepts no responsibility in cases where the instructions contained in this document are not observed.
NOTE: the oven functions, properties and accessories cited in this manual will vary, depending on the model you have purchased.

 Safety Indications
Only use the oven for its intended purpose, that is only for the cooking of foods; any other use, for example as a heat source, is considered improper and therefore dangerous. The manufacturer cannot be held responsible for any damage resulting from improper, incorrect or unreasonable usage. The use of any electrical appliance implies the observance of some fundamental rules:-

  • do not pull on the power cable to disconnect the plug from the socket;
  • do not touch the appliance with wet or damp hands or feet;
  • in general the use of adaptors, multiple sockets and extension cables is not recommended;
  • in case of malfunction and/or poor operation, switch off the appliance and do not tamper with it.

Electrical Safety

The power supply to which the oven is connected must conform with the laws in force in the country of installation. The manufacturer accepts no responsibility for any damage caused by the failure to observe these instructions. The oven must be connected to an electrical supply with an earthed wall outlet or a disconnector with multiple poles, depending on the laws in force in the country of installation. The electrical supply should be protected with suitable fuses and the cables used must have a transverse section that can ensure correct supply to the oven.
The oven is supplied with a power cable that should only be connected to an electrical supply with 220-240 Vac power between the phases or between the phase and neutral. Before the oven is connected to the electrical supply, it is important to check:-

  • power voltage indicated on the gauge;
  • the setting of the disconnector.
  • The grounding wire connected to the oven’s earth terminal must be connected to the earth terminal of the power supply.
    Before connecting the oven to the power supply, ask a qualified electrician to check the continuity of the power supply’s earth terminal. The manufacturer accepts no responsibility for any accidents or other problems caused by failure to connect the oven to the earth terminal or by an earth connection that has defective continuity.

NOTE: as the oven could require maintenance work, it is advisable to keep another wall socket available so that the oven can be connected to this if it is removed from the space in which it is installed. The power cable must only be substituted by technical service staff or by technicians with equivalent qualifications.
A low light around the central main switch could be present when the oven is off. This is a normal behavior. It can be removed just turning the plug upside down or swapping the supply terminals.


After each use of the oven, a minimum of cleaning will help keep the oven perfectly clean. Do not line the oven walls with aluminium foil or single-use protection available from stores. Aluminium foil or any other protection, in direct contact with the hot enamel, risks melting and deteriorating the enamel of the insides. In order to prevent excessive dirtying of your oven and the resulting strong smokey smells, we recommend not using the oven at very high temperature. It is better to extend the cooking time and lower the temperature a little. In addition to the accessories supplied with the oven, we advise you only use dishes and baking moulds resistant to very high temperatures.


The manufacturers have no obligation to carry this out. If the assistance of the manufacturer is required to rectify faults arising from incorrect installation, this assistance is not covered by the guarantee. The installation instructions for professionally qualified personnel must be followed. Incorrect installation may cause harm or injury to people, animals or belongings. The manufacturer cannot be held responsible for such harm or injury. The oven can only be located high in a column. Before fixing, you must ensure good ventilation in the oven space to allow proper circulation of the fresh air required for cooling and protecting the internal parts. Make the openings specified on last page according to the type of fitting.

Waste management and environmental protection

This appliance is labelled in accordance with European Directive 2012/19/EU regarding electric and electronic appliances (WEEE). The WEEE contain both polluting substances (that can have a negative effect on the environment) and base elements (that can be reused). It is important that the WEEE undergo specific treatments to correctly remove and dispose of the pollutants and recover all the materials. Individuals can play an important role in ensuring that the WEEE do not become an environmental problem; it is essential to follow a few basic rules:

  • the WEEE should not be treated as domestic waste;
  • the WEEE should be taken to dedicated collection areas managed by the town council or a registered company.
  • In many countries, domestic collections may be available for large WEEEs. When you buy a new appliance, the old one can be returned to the vendor who must accept it free of charge as a one-off, as long as the appliance is of an equivalent type and has the same functions as the purchased appliance.

Where possible, avoid pre-heating the oven and always try to fill it. Open the oven door as infrequently as possible, because heat from the cavity disperses every time it is opened. For a significant energy saving, switch off the oven between 5 and 10 minutes before the planned end of the cooking time, and use the residual heat that the oven continues to generate. Keep the seals clean and in order, to avoid any heat dispersal outside of the cavity. If you have an electric contract with an hourly tariff, the “delayed cooking” programme makes energy saving more simple, moving the cooking process to start at the reduced tariff time slot.

 Declaration of compliance

By placing the mark on the appliance, we are confirming compliance to all relevant European safety, health and environmental requirements which are applicable in legislation for this product.

Hereby, Candy Hoover Group Srl declares that the radio equipment is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:

Product Description

 OverviewCANDY Watch Touch Ovens Instruction Manual  & troubleshooting 3
  1. Control panel
  2. Shelf positions (lateral wire grid if included)
  3. Metal grill
  4. Drip pan
  5. Fan (behind the steel plate)
  6. Oven door
  7. Touch control panel on the door
  8. Camera

Accessories (According to model) 1 Metal grillCANDY Watch Touch Ovens Instruction Manual  & troubleshooting 4Holds baking trays and plates.
2 Drip panCANDY Watch Touch Ovens Instruction Manual  & troubleshooting 5
Collects the residues that drip during the cooking of foods on the grills.
3 Lateral wire gridsCANDY Watch Touch Ovens Instruction Manual  & troubleshooting 6
It located at both sides of the oven cavity. It holds metal grills and drip pans.

Use of the Oven

User interface description
  1. Main switch on/off
  2. LCD touch interfaceCANDY Watch Touch Ovens Instruction Manual  & troubleshooting 7

Product Setting

  • At first launch you need to follow an installation process to be able to use the oven. Press START to go ahead.
  • Select the language from the drop down menu. Press NEXT to go ahead.
  • Set the date from the calendar. Set the time from the clock. Press NEXT to go ahead.
  • Select your home network from the drop down menu. Insert the password related to your home network. Press NEXT to go ahead and wait the loading or connection.
    NB: The oven works even if not connected to the network. It’s possible to enroll the oven to the network at a later time.
  • The enrollment has been completed successfully. Press NEXT to go ahead to the last step.
  • The installation process is completed. Press GO TO HOME PAGE to start to use the oven. For more details see quick guide.
Technology Wi-Fi BLE



IEEE 802.11b/g/n

Bluetooth v2.1+EDR/BT v3.0/BT V4.0+HS
Frequency Band(s) [MHz] 2400÷2497 2400÷2497
Maximum Power [mW] 51.7 10

First Use

Clean the oven before using for the first time. Wipe over external surfaces with a damp soft cloth. Wash all accessories and wipe inside the oven with a solution of hot water and washing up liquid. Set the empty oven to the maximum temperature and leave on for about 1 hour, this will remove any lingering smells of newness.

 Operating In Manual Mode
  • Press the Manual Mode tab to set a cooking in 3 simple steps.
  • Swipe and select the desired cooking function. Press NEXT to go ahead
  • Swipe to select the desired temperature. Press NEXT to go ahead or BACK to return to the cooking functions selection.
  • Swipe to select the cooking time. Press START to begin the cooking or BACK to return to the temperature setting.
  • In this screen it is possible to:
  • exclude pre heating (setted by default)
  • set delayed start
  • When a cooking is running you can:
  • change the temperature
  • change the cooking time
  • press the webcam icon to watch inside the oven cavity
  • press STOP to finish the cooking.
 Home Page – Main FunctionsCANDY Watch Touch Ovens Instruction Manual  & troubleshooting 8


  • The oven is sending all the data to the connected device.
  • The oven is not sending the data to the device.
  • NB: If this option is activated, the oven is driven only by the connected device.
FUNCTION                    WHAT IS DOES



In this mode it is possible to chose cooking functions, temperature and cooking duration, by 3 simple steps. In this mode it is also possible to set a cooking delay.

By default the preheating option is active: to turn it off click on the symbol


In this mode it is possible to save and, in a second time, to select, customized cooking programs.


In this mode it is possible to select a suggested cooking program. During the cooking fase, it is possible to change temperature and cooking duration.


In this mode it is possible to select some tutorial about how to prepare several recipes. At the end of the video it is possible to start cooking. It is not possible to change the cooking parametrs.




If the icon is active the oven door is connect to the net.


Selecting this icon it will be possible to set language, date and time, wi-fi, bluetooth, camera brightness setting. Supported bluetooth devices are audio speakers only. Supported bluetooth standars are: 2.1, 3.0, 4.0



Selecting this icon it will be possible to surf on the internet within a list of authorized websites.




On the first use, with a long press on the icon you enroll the oven on the net.

With a short press on the icon, the remote control of the oven it activated. If this option is activated the oven is driven ONLY by the connected device. To control again the oven directly on the door screen click again on the icon.

To see webcam streaming on the external device (APP SIMPLY-FI), the door must be connected to the net. (THE INTERNET CONNECTION ICON MUST BE ACTIVATED)







Pressing the webcam icon you can watch inside the oven to monitor the cooking progress.

To protect the camera, the system puts it in stand-by after 1 minute (5 minutes in case of grill function). To restart it, press the button again.

Do not keep it switched on for too long.

In case of cooking at high temperature, if the camera stays on for a long time, its colours might change.

This is a standard phenomenon and disappears when the camera and/or the oven are   cooled



Touching this icon you go back to home page

Cooking Modes

Function Dial Function  (Depends on the oven model)
  LAMP: Turns on the oven light.

DEFROST: When the dial is set to this position. The fan circulates air at 40oC around the frozen food so that it defrosts in a few minutes without the protein content of the food being changed or altered.




KEEP WARM: This is recommended to reheat precooked foodstuff, positioning the shelf on the second level from top, or to defrost bread pizza or pastry by positioning the shelf on the lower level.

The temperature is preset in 60°C constant, no regulation is possible.





MULTI-LEVEL: We recommend you use this method for poultry, pastries, fish and vegetables. Heat penetrates into the food better and both the cooking and preheating times are reduced. You can cook different foods at the same time with or without the same preparation in one or more positions. This cooking method gives even heat distribution and the smells are not mixed.

Allow about ten minutes extra when cooking foods at the same time.


CONVENTIONAL: Both top and bottom heating elements are used. Preheat the oven for about ten minutes. This method is ideal for all traditional roasting and baking. For seizing red meats, roast beef, leg of lamb, game, bread, foil wrapped food (papillotes), flaky pastry. Place the food and its dish on a shelf in mid position.







BOTTOM HEATING + FAN: The bottom heating element is used with the fan circulating the air inside the oven. This method is ideal for juicy fruit flans, tarts, quiches and pâté.

It prevents food from drying and encourages rising in cakes, bread dough and other bottom-cooked food. Place the shelf in the bottom position.












GRILL:                Use                the                grill                with                the                door                closed.   The top heating element is used alone and you can adjust the temperature. Five minutes preheating is required to get the elements hot. Success is guaranteed for grills, kebabs and gratin dishes. White meats should be put at a distance from the grill; the cooking time is longer, but the meat will be tastier. You can put red meats and fish fillets on the shelf with the drip tray underneath.


PIZZA: With this function hot air circulated in the oven to ensure perfect result for dishes such as pizza or cake.






BOTTOM HEATING: Using the lower element. Ideal for cooking all pastry based dishes. Use this for flans, quiches, tarts, pate and any cooking that needs more heat from below.



The “COOK LIGHT” function allows you to cook in a healthier way, by reducing the amount of fat or oil required. Thanks to a special combination of cooking functions and a pulsating cycle of air, it will retain the moisture content of the food, grilling the surface and using a shorter cooking time, without compromising on taste.

It is particularly suitable for cooking meat, roasted vegetables and omelettes. The cycle of pulsed air keeps the humidity inside the oven and the moisture content of the food, preserving the nutritional values and ensuring a rapid uniform cooking process.

Try all your recipes and reduce the amount of dressing you usually use and experience the lightness of this new function!

Tested in accordance with the EN 60350-1 for the purpose of energy consumption declaration and energy class.

Simply-fi oven enrollment

Installing the appliance

Install the appliance in accordance to the installation guide within this instruction book.
Once this step has been completed, ensure the appliance is working by controlling the appliance directly using the control panel.
Please take the time to read the program guides and functions as this will help you to take full advantage of the features of your new appliance.
Please ensure that the clock time is set before trying to enrol an oven.
Locating your Wi-Fi Password
Locate the Wi-Fi Password (WPA/WEP Key) which is normally found on the back of your Wi-Fi router.
If you are having trouble locating the Wi-Fi Password, please contact your Internet Provider.
Take a note for later use
Once you have your Wi-Fi Password, please take a note of it here below as you will need this later on whilst connecting the appliance to the App.
Router name _______________________________
Password (WPA/WEP Key) _______________________________
Connect your device to the same Wi-Fi router ready to install the App
Downloading the App
Download the Candy simply-Fi App from the App store relevant to your device. Note – The App is suitable for iOS (version 8 and greater) and Android (version 4.4 and greater). App Name – Candy simply-Fi
Locating your product code
Locate the product code of your appliance with the help of the image below.
Take note of the serial number
The illustration shows the format of the appliance information. Write your product serial number here below: Serial number (16 digits)

CANDY Watch Touch Ovens Instruction Manual  & troubleshooting 9

Step 1:
Open the App Candy simply-Fi. Create your account by tapping on “Sign-Up”. Accept the privacy policy and complete the fields.
Note: You can explore all the features of the full simply-Fi range by tapping on “Demo”.
Step 2:
In the homepage, tap on the appliance that you want to connect and tap on “Ok”.
Step 3:
Insert the 16 digits serial number that you wrote down above and tap on “Next”. Check that the product details are correct and then tap on “Confirm”.

Step 4:
Once your appliance has been recognized, tap on “Next”. Then, you have 5 minutes to complete the process; otherwise, you will need to start it again.

Step 5:
Long press the icon to enroll the appliance.

Step 6:
Exit the Candy simply-Fi app. Go to your device Wi-Fi settings.
Step 7:
In the list of available Wi-Fi networks, select “WIFIOVEN-xyzk”. If you do not find it, wait few more seconds or do a new scan.
Step 8:
Exit from the settings of your device. Return to the Candy simply-Fi App and wait for the App to detect the appliance. Once the “Wi-Fi Network is active” screen appears, tap on “Next”
Step 9:
Your home Wi-Fi Network will be automatically set by the App. (If not, enter the name of your home Wi-Fi network, paying attention to lowercase and uppercase letters). Insert the Wi-Fi Password (WPA/WEP Key), then tap on “Confirm”.
Step 10:
For more advantages, you can Register your product by tapping the dedicated button.nTap on “Start” to return in the App Homepage. Remote control mode
With a short press on the icon the oven can be remotly controlled. To control again the oven directly on the door screen do a short press on the icon.
To see webcam streeming on the external device (APP SIMPLY-FI), the door must be connected to the net.

If the set up does not complete:

It’s important that there is a good Wi-Fi signal strength from the home router to the appliance: low Wi-Fi signal strength would cause the final stage of the set up to fail. To establish if this is the case, start the connection process again from Step 1; once at Step 8, place with your device (smartphone or tablet) next to the router and search for “WIFIOVEN-xyzk” net generated by the machine. If this does not come up as an option, this means the router cannot see the appliance. In this case, we recommend to bring the router near to the machine (if possible) or contact your internet provider and require the assistance to purchase a compatible “Wi-Fi Range Extender” to increase the signal strength.


Technology Wi-Fi
Standard IEEE 802.11b/g/n
Frequency Band(s) [MHz] 2412÷2484
Maximum Power [mW] 41.4

Oven cleaning and maintenance

General notes on cleaning

The lifecycle of the appliance can be extended through regular cleaning. Wait for the oven to cool before carrying out manual cleaning operations. Never use abrasive detergents, steel wool or sharp objects for cleaning, so as to not irreparably damage the enamelled parts. Use only water, soap or bleach-based detergents (ammonia). GLASS PARTS
It is advisable to clean the glass window with absorbent kitchen towel after every use of the oven. To remove more obstinate stains, you can use a detergent-soaked sponge, well wrung out, and then rinse with water.
If dirty, the seal can be cleaned with a slightly damp sponge.
Clean accessories with a wet, soapy sponge before rinsing and drying them: avoid using abrasive detergents.
After using the grill, remove the pan from the oven. Pour the hot fat into a container and wash the pan in hot water, using a sponge and washing-up liquid. If greasy residues remain, immerse the pan in water and detergent. Alternatively, you can wash the pan in the dishwasher or use a commercial oven detergent. Never put a dirty pan back into the oven.



  1. Remove the wire racks by pulling them in the direction of the arrows (see below)
  2. To clean the wire racks either put them in the dishwasher or use a wet sponge, ensuring that they are dried afterwards.
  3. After the cleaning process install the wire racks in reverse order.

CANDY Watch Touch Ovens Instruction Manual  & troubleshooting 10


  1. Open the oven door.
  2.  Lock the hinges, remove the screws and remove the upper metal cover by pulling it upwards.
  3. Remove the glass, carefully extracting it from the oven door (NB: don’t remove any other glass or component).
  4. At the end of cleaning or substitution, reassemble the parts in reverse order.
  5. On all glass, the indication ”Low-E” must be legible and positioned on the left side of the door, close to the left-hand lateral hinge. In this way, the printed label of the first glass will be inside the door.

CANDY Watch Touch Ovens Instruction Manual  & troubleshooting 11CHANGING THE LAMP BULB

  1. Disconnect the oven from the mains supply.
  2. Undo the glass cover, unscrew the bulb and replace it with a new bulb of the same type.
  3. Once the defective bulb is replaced, replace the glass cover.CANDY Watch Touch Ovens Instruction Manual  & troubleshooting 12

NOTE: For any issue with the led light system present in the door contact costumer service.CANDY Watch Touch Ovens Instruction Manual  & troubleshooting 13



Setting up CANDY Watch Touch Ovens Instruction Manual is easy with these step-by-step instructions. Follow the steps are you are set-up in no time.

Using CANDY Watch Touch Ovens Instruction Manual is simple by using this manual. Follow the instructions one by one and everything will be fine

Is CANDY Watch Touch Ovens Instruction Manual stuck or not working properly? By resetting it you can set it back to the standard settings and everything should be back to normal. This works in many cases when problems arise.

This page contains the complete user instructions & manual for CANDY Watch Touch Ovens Instruction Manual

All symbols, colors and codes for CANDY Watch Touch Ovens Instruction Manual are explained in this instruction manual. You can find everything you need and moree