WWD2-4IW
Daintree® Wireless Controls
Wireless Scene Switch
Product Overview
The Daintree® Wireless Scene Switch is a battery-powered wall switch for use in a Daintree Networked or Daintree EZ Connect application. The WWD2-4IW device installs into an existing junction box to replace the existing wall-mounted switch with a wireless solution that enables on/off and either dimming or scene selection commands to be delivered to the luminaires in its commissioned space. The WWD2-4IW device can provide either dual zone dimming control or allow the user to select from four configured scenes. The buttons on the WWD2-4IW can be changed to clearly indicate the operation mode of the device. The communication with the Daintree EZ Connect or Daintree Networked system utilizes a secure and reliable wireless connection which helps minimize installation costs and complexity.
BEFORE YOU BEGIN
Read these instructions completely and carefully. Save these instructions for future use.
WARNING / AVERTISSEMENT
RISK OF ELECTRIC SHOCK
- Disconnect power before service installation, or maintenance of the product.
RISK OF FIRE - Follow all relevant IEC or UL instructions and local building codes.
RISK OF INJURY - • Wear safety glasses and gloves during installation and servicing.
Save These Instructions
Use only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.
Prepare Electrical Wiring Electrical Requirements
- When replacing a line voltage switch, the power must be off at the branch circuit breaker. Bypass the line voltage switch to provide uninterrupted power to the fixtures and make sure the connection is properly insulated before installing the wireless switch.
IMPORTANT
To ensure the product warranty is valid, please ensure all installation instructions and environmental conditions for storage and operation are complied with. Installation to be performed by factory trained or qualified personnel.
Installation of Back Housing onto Junction Box
 |
||
| Disconnect power to the junction box | Remove the junction box cover plate | Uninstall existing wall switches from the junction box. |
 |
||
| Terminate wires (previously connected to wall switch) with wire nuts. | For proper installation into a dual gang junction box, the tabs between adjacent back housings must be removed. Carefully observe the correct orientation (the UP arrow should be in the upper right corner on each back housing). After double checking the product orientation, break off the necessary tabs using pliers. | Install the back housing(s) of the wall dimmer(s) into the wall box. |
DOUBLE CHECK PRODUCT ORIENTATION BEFORE BREAKING OFF TABS.
The wall dimmer will only install into the back housing in one orientation.
Break off tabs only after the correct product orientation has been confirmed.
Installation of Device into Back Housing
 |
||
| Use two standard screwdriver to remove the devices from the back housing | Separate the battery cover from the device. Pull the plastic insulation strip out of the battery compartment. Put the battery cover back on the device. | Insert the back housing piece into the junction box and secure with two screws. |
 |
|
| Install the main body of the device into the back housing. | Install the faceplate onto the device. Note: Device supports the use of other standard faceplates on the market. |
Network Reset
To reset the network of the device, remove the faceplate from the device. Then press and hold the reset button for 5 seconds. Install the faceplate back onto the device. Press either dimming up or down button to enter the pairing mode to join the device to a network.
Personality Change
 |
|
| Hold the reset button and 2nd button for 5 seconds to change the personality to dual zone mode. | Hold the reset button and 4th button for 5 seconds to change the personality to scene mode. |
 |
||
| Squeeze the clips on the side of the button module to remove the button module from the device. | Press the replacement button module with the desired printing onto the device. | Please contact if you would like to purchase customized buttons. |
Battery Replacement
 |
||
| The device’s LED flashing on for 2 seconds every 30 seconds indicates that the batteries need to be replaced. | Remove the device from the back housing. | Separate the battery cover from the device. Replace the batteries with AAA batteries. All batteries need to be replaced at the same time. |
 |
|
| Install the main body of the device into the back housing. | Install the faceplate onto the device. The device will rejoin its network automatically. |
Product Dimensions
Product Operation
 |
First Button Short press Double short press Hold |
Dual Zone Personality Zone 1 lights ON at previous level Zone 1 lights ON at 100% output Turn Zone 1 ON and dim up |
Four Scene Personality SCENE 1 turns ON |
 |
Second Button Short press Double short press Hold |
Zone 1 lights OFF Zone 1 lights ON at minimum dimming level Turn Zone 1 ON and dim down or dim down if lights are already ON |
SCENE 2 turns ON |
 |
Third Button Short press Double short press Hold |
Zone 2 lights ON at previous level Zone 2 lights ON at 100% output Turn Zone 2 ON and dim up |
SCENE 3 turns ON |
 |
Forth Button Short press Double short press Hold |
Zone 2 lights OFF Zone 2 lights ON at minimum dimming level Turn Zone 2 ON and dim down or dim down if lights are already ON |
SCENE 4 turns ON |
LED Indicator
| Rapid flash (12 times per second) for up to 30 seconds | Device is trying to join a ZigBee network |
| Solid ON for 10 seconds | Device successfully joined a ZigBee network |
| Flashes once (100ms duration) | Device has been activated while in the network |
| Flashes ON 2 seconds every 30 seconds | Batteries need to be replaced |
| Flashes twice (100ms duration) | Device has entered dual zone personality mode. |
| Flashes four times (100ms duration) | Device has entered four scene personality mode. |
Technical Data
Product Specifications
| Dimensions | 114mm H x 70mm W x 36mm D |
| Weight | 130g |
| Power Supply | (4) AAA1.5V battery |
| Battery Life | 5 years (normal operation) |
| Operating Environment | -10°C to 40°C (Indoor Use Only) |
| Status Indicator | Network join status, button triggered |
| Mounting | Mounts into junction box |
| Warranty | 5 years |
| Purpose of Control | Operating Control |
| Construction of Control | Independently Mounted |
| Type 1 Action | |
| Pollution Degree 2 | |
Product Availablity
SKU
DESCRIPTION
ARTICLE NO.
WWD2-4IW
93141338
Daintree Wireless Controls Wall
Dimmer, In Wall, 4 Button, Battery
Product Certifications
