EUROmair 30950 Eole T2 Paint Sprayer User Manual

EUROmair 30950 Eole T2 Paint Sprayer User Manual & troubleshooting

EUROmair 30950 Eole T2 Paint Sprayer User Manual  & troubleshooting 1

EUROmair 30950 Eole T2 Paint Sprayer

EUROmair 30950 Eole T2 Paint Sprayer User Manual  & troubleshooting 2

WARNING

  •  Respect all the safety standards before running the equipment.
  •  Use the equipment only for the applications specified in the manual.
  •  Always remain alert when using the equipment.
  •  Transport the machine using the handles or the appropriate grips.
  •  During the breaks, disconnect electrically the machine.
  •  Run the equipment to its nominal voltage.
  •  Let at least 50 cm of free space between the equipment and any obstacle so that the airflow  is not blocked.
  •  Know how to quickly stop the equipment in case of necessity.
  •  Never use the equipment while it is running abnormally or it is defective.
  •  Do not direct a water jet or flammable liquid on the machine.
  •  Never direct an air jet or product jet on a person or an animal.
  •  Do not touch the warm surfaces of the equipment.
  •  Always wear adequate body protection (glasses, gloves, overall and mask) and pay attention to long hair.
  •  Never touch moving parts.
  •  Do not insert any object or the hands inside the protection grids to avoid any accident or
    damage to the machine.
  •  For any outside job, only use appropriate extension cords.
  •  Maintain the equipment carefully and clean it properly after every use.
  •  Disconnect the equipment before any intervention.
  •  Avoid absolutely unscrewing any connection while the machine is under pressure.
  •  Check the damaged parts.
  •  Do not clean the plastic parts with solvent.
  •  In case of damage of the electric cable or the plug, do not run the machine and contact a
  • licensed After-Sale Service to put genuine parts instead of the defective ones.
  •  In case of needed After-Sale Service, always specify the machine model and its serial number.
  •  For any replacement of parts, only use genuine parts.
  •  Do not modify the machine.
  •  Do not cut or dismantle the protection grids.
  •  Do not open the electric box.

WORKSPACE

  •  Maintain the workspace clean and clear.
  •  Ambient operating temperature must be from 5°C and 35°C.
  •  Do not use the equipment in a potentially explosive area.
  •  Do not place any potentially inflammable objects in close proximity to the machine.
  •  Take away every not qualified person from the working area of the machine, as well as children and animals.
  •  In case of installation of the machine on scaffolding or a plan above ground level, attach the machine
    to avoid any fall while operating.
  •  Do not install the equipment on an inclined surface to avoid the risks of unexpected moves or falls.
    HOSES
  •  Always use hoses and connections adapted to the used product (genuine parts), do not try to fix it.
  •  Do not walk on the hoses, do not bend them.
  •  Do not use the hoses to pull the machine.
    STORAGE
  •  Keep the equipment in a clean and clear area in which the temperature does not exceed +35°C.

GROUND CONNECTOR
All the machines must be connected to the ground when they work to protect the operator from electric shocks. Our machines are all equipped with standardized connection plugs. The electric connection must be made by a qualified technician. It is forbidden to modify or dismantle the machine, especially the electric box. Repairs must be made by an authorized center or our After-sale Service. During any intervention on the machine, make sure that the ground is well reconnected.
EXTENSION CORDS
During the use of an extension cord, make sure that it is not crushed or damaged and that it contains ground. Check that the section of the used extension cord is sufficient to support the machine when it is working. A too-thin extension cord can cause voltage drops or overheat of the machine. In case of use of a cable reel, it is imperative to unwind it entirely, otherwise, the equipment can be damaged. The section must be proportional to the length of the cord.
END OF LIFE OF THE PRODUCT
At its end of life, the machine must not be eliminated with the other household waste. The uncontrolled elimination of waste can harm the environment or human health. Individuals are invited to contact the distributor which sold them the product or to inquire with their city hallto know where and how to get rid of the product so it can be recycled while respecting theenvironment. Under the regulation of Waste of Electrical and Electronic Equipment (WEEE), we undertake to process the used EEEs according to the following provisions: applicable only to products on themarket since 08/13/05, under the brands EUROPE PROJECTION or VOLUMAIR, products of other brands sold by our company (upon presentation of the corresponding invoices), products that operate using electrical energy (for example, thermal washers or compressors do not fall into this category). Treatment modality WEEE returns are collected by our clients/distributors at their own expense to our collection points in Antony (92) or Rousset sur Arc (13). Upon receipt, the products are sorted by our employees and directed to the most appropriate processing channels. For any further information, please contact our hotline at +33 4 42 29 08 96 or [email protected]

DESCRIPTION

Compact, fast, handy, lightweight and easy to use turbine it is ideal for small jobs. APPLICATIONS Allows a large number of products to be applied (lacquers, varnishes, primers, in aqueous phase or in solvent phase. APPLICATIONS Allows a large number of products to be applied (lacquers, varnishes, primers, in aqueous phase or in solvent phase …).

TECHNICAL CHARACTERISTICS

TURBINE
Stages 2
Pressure 0,3 bar
Air flow-rate adjustment no
Power 1100 W
Electrical supply 230 V / 10 A / 50 and 60 Hz
Hose length 4 m
Dimensions (l x w x h) 27 x 20 x 36 cm
Weight 7 kg
Noise level 91 Lwa
SPRAY-GUN
Product flow-rate adjustment yes
Jet width adjustment yes
Air pressure adjustment no
Bowl capacity 1 L
Dimensions (L x w x h) 18 x 11 x 29 cm
Weight 0,83 kg

YOUR MACHINE (continued) 

 

EUROmair 30950 Eole T2 Paint Sprayer User Manual  & troubleshooting 3

  1. A Nozzle ring
  2. B 1 liter bowl
  3. C Trigger
  4. D Air inlet coupling
  5. E Product flow-rate adjustment thumbwheel
  6. F Atomization kit
  7. F1 Diffuser head
  8. F2 Jet nozzle
  9. F3 Needle

IDENTIFICATION OF THE TURBINE COMPONENTS

EUROmair 30950 Eole T2 Paint Sprayer User Manual  & troubleshooting 4

  • G Ventilation filter
  • H Air outlet coupling
  • I Starting switch
  • J Electrical supply cable
  • K Air filter

USE OF THE MACHINE PREREQUISITES

  •  The electric connection has to be 230 V – 16 A – 50 or 60 Hz.
  •  Be careful to only use paints that have not dried and which do not contain dry particles (otherwise, filter the paint with a strainer).
  •  When using a chlorinated product, it is imperative to dilute the product (5% of pure product maximum).
  •  Before use, verify the air filter foam (K). Replace it if it is used or missing by loosening the metallic cover.
  •  Choose the ideal needle kit depending on the paint which will be used. To change the nozzle, loosen the ring (A).

Choice of the atomization kit

  •  The spray gun can be equipped with 5 different jet nozzles.
  •  Choosing the right atomization kit is essential to obtaining a perfect finish. This choice has to be made according to the work to be done, the kind of paint, the dimensions of the objects, and the surfaces to be covered (see table below).
Nozzle Ø Work to be made Viscosity Product to be used
 

0,50 mm

Finishing jobs, low output, small areas, decoration, refinishing, shadow, stain, etc… 15

seconds

 

Light, thin, chromate products, etc…

 

1 mm

All kind of varnish jobs, house-hold appliances, furniture, car bodywork, aviation, etc… 26

seconds

All products with normal dilution, lac-quer, varnish, oil based, cellulosic, polyu-rethane, etc…
1,50 mm For usual jobs, high output, large areas  

+30

seconds

Bottom layer, primer, oil based paints, dispersion, etc…
2,50 mm Thick layer, high output, large areas, speckled, decorative ef-fects, building, insulation, etc… Glues, heavy products, minium, gelcoat, oilbased varnish, etc…
3,50 mm

ATOMIZATION

  1.  Prepare the surface to be painted (sanding, cleaning, etc…).
  2.  Fill the bowl with paint (around 3/4 of the bowl).
  3.  Mount the spray-gun body onto the spray-gun.
  4.  Connect the hose on the (H) coupling on the turbine side and the (D) coupling on the spray-gun side.
  5.  Connect the turbine electrically and press the switch (I).
  6.  For an optimal atomization, hold the spray-gun as horizontal a possible. The paint jet has to be perpendicular to the surface to be painted, with a distance of about 20 cm.
  7.  Proceed by crossed sections, horizontal and vertical, directing the diffuser head as needed.
  8.  Move the spray-gun with an uniform movement and a regular speed. Release the trigger at the end of each section.
  9. To avoid bleeding, press the trigger only after having begun the movement of the spray-gun.
  10.  Do not try to cover everything in one layer, prefer applying a second one.

Dilute a part of the paint with the appropriate thinner. Fill the viscosimeter to the top and let the liquid flow and monitor the time it takes until the trickle of paint becomes discontinuous. Check to see if the time corresponds to the indications in the table below: – if the time is longer, increase the dilution – if the time is shorter, add more paint

BUILDING PAINT   INDUSTRIAL PAINT
PRODUCTS TIME PRODUCTS TIME
Oil paint 25 to 30 sec. Hammered finish 30 to 50 sec.
Vinyl paint 30 to 35 sec. Anti-rust 25 to 33 sec.
Acrylic paint 30 to 35 sec. Lacquer, polyurethane 25 to 30 sec.
Pliolite 35 to 40 sec. Lacquer, synthetic 22 to 27 sec.
Lacquer, brilliant, satin 25 to 27 sec. Varnish, synthetic 20 to 22 sec.
Mat ceiling paint 25 to 30 sec. Cellulosic 18 to 22 sec.
Anti-rust 25 to 33 sec. Chromate and Wash-primer 18 to 22 sec.
Impression 20 to 25 sec. Metallised 18 to 20 sec.

SPRAY SETTING
To increase or decrease the product flow-rate, use the wheel (E) at the back of the spray-gun:

  •  screw to decrease the flow-rate
  •  unscrew to increase the flow-rate
    To increase or decrease the jet width, use the ring (A):
  •  tighten to obtain a wider jet
  •  unscrew to obtain a more narrow jet
    To obtain differents jets, direct the diffuser head as indicated below:

EUROmair 30950 Eole T2 Paint Sprayer User Manual  & troubleshooting 5

SETTING UP OF THE EXTENSION POLE

  •  The extension pole takes the place of the diffuser head and the jet nozzle.
  •  Dismantle the ring (A).
  •  Dismantle the jet nozzle (F2).
  •  Mount the 1,5 mm needle.
  •  Be sure the joint is well placed.
  •  Mount the extension pole with the ring (A).
  •  Block the ring.
     CHANGE OF THE ATOMIZATION KIT
  •  Remove the ring (A) and the diffuser head (F1).
  •  Unscrew the setting wheel (E) and remove the spring.
  •  Press the trigger, the needle (F3) comes out easily from its housing.
  •  Unscrew the jet nozzle using the key delivered with the spray-gun.
  •  Reassemble the new nozzle jet and screw properly to avoid leaks.
  •  Reassemble the spray-gun in the reverse order of the disassembly, with the new diffuser head.

CLEANING

Spray-gun cleaning

  •  Empty the product remaining into the bowl.
  •  Clean the insde and the outside of the bowl with help of a paintbrush.
  •  Fill the bowl with water and spray for circulating it. The product passages will so be cleaned. In case of a prolonged standstill or every week
  •  Dismantle and clean the atomizing kit (F)
  •  Clean the inside of the spray-gun with little pins and solvant, as well as the tubes
  •  Oil the moving parts of the spray-gun with a very fluid oil
  •  Grease with a consistent grease every thread pitch, the front side of the needle nozzle, the 2 springs and the centring nut which slides into the back plug
  •  Verify and tighten the nut gland if needed
  •  Loosen the metal cover of the ventilation filter (G), remove the filter and blast it with help of a pressure cleaner.
  •  Unscrew the metal cover of the air filter (K), remove the filter and blast it with help of a pressure cleaner.

WARRANTY CONDITIONS

Each piece of equipment is delivered inspected and tested. We exclude any warranty for visible defects, not notified by the customer within 48 hours. The equipment sold is guaranteed during the manufacturer’s warranty from the date of purchase, as specified on the original proof of purchase, and under the conditions defined by the manufacturer. This warranty covers any equipment against any manufacturing or material defect, under normal conditions of use. Insofar as the customer is presumed to be a professional of the same field of specialty, this warranty covers only the defect of the conception of the equipment rendering it unfit for its use, which could not be detected by a professional buyer. The defects or deteriorations caused by natural wear, external accident or a modification, use, storage or treatment of the equipment not planned by the manufacturer, nor specified by ourselves, are excluded from any warranty. Are expressly excluded from the warranty the defects resulting from improper use, the application of abrasive or corrosive products, an inappropriate installation, the negligence, an insufficient maintenance or cleaning, inappropriate conditions of storage, chemical, electronical or electric influences, any change in the normal process of use. The following wearing parts are not covered by the warranty (non-exhaustive list): rotors, stators, driving shafts, connecting rods, seals, cleaning balls, spray guns, lance, nozzle, hose, needle kits, cylinders, piston rods, prime/spray valve assy, seal kits, membranes, suction and delivery valves, carding machine vanes, filters, oils, chains and quick-release clip. The warranty also excludes the equipment on which the serial number was erased or made illegible, on which unauthorized people made attempts of repair, which were totally or partially dismantled. In all cases, our liability shall be limited to the amount paid by the customer for non-compliant equipment.
Any legal action of the customer against us relating to the warranty of the equipment shall be barred 1 year after the date of discovery of the defect. The customer shall have to prove the date of this discovery. Request for Warranty For any request related to the repair of an equipment covered by the manufacturer’s warranty, the customer shall have to fill the warranty form, available on our website to the following address: https://www.euromair. com/en/after-sales-service/For a full dossier, the following documents shall have to be attached:

  •  the purchase invoice of the final user
  •  pictures of the defective parts of the equipment
  •  a description of the breakdown
  • the quote of labor if the customer is certified by EUROMAIR for repairing the equipment

No invoice of labor shall be taken into account without our prior approval. Analysis of the breakdown by our technical department A file number shall be given to the customer and an answer shall be provided within 48 working hours afterreception, provided that the request for warranty is considered as full. In the event the equipment is covered by the manufacturer’s warranty, we shall confirm the warranty to the customer and send him a quote (without price) detailing the parts to be changed and any comments. Return of replacement parts Replacement parts must be ordered with a warranty agreement number and will be made available to the customer at our factory. The conditions of return of the equipment are detailed in our Delivery terms. In the case of a warranty claim on an on-board component such as a Kohler, Honda or Vanguard engine in a machine manufactured by us, only the manufacturer of the component is able to validate the warranty coverage. In this case, the request must be addressed directly to the manufacturer of the component or to its nearest authorised representative. The Euromair, Euromair MPC or Mixer service centres may be considered as the manufacturer’s representatives if they are the closest. As this principle also applies to batteries, our supplier Parts Holding Europe, or one of its sister companies, remains your contact for your requests (https://www.
partsholdingeurope.com/).

FAQ


Setting up EUROmair 30950 Eole T2 Paint Sprayer User Manual is easy with these step-by-step instructions. Follow the steps are you are set-up in no time.

Using EUROmair 30950 Eole T2 Paint Sprayer User Manual is simple by using this manual. Follow the instructions one by one and everything will be fine

Is EUROmair 30950 Eole T2 Paint Sprayer User Manual stuck or not working properly? By resetting it you can set it back to the standard settings and everything should be back to normal. This works in many cases when problems arise.

This page contains the complete user instructions & manual for EUROmair 30950 Eole T2 Paint Sprayer User Manual

All symbols, colors and codes for EUROmair 30950 Eole T2 Paint Sprayer User Manual are explained in this instruction manual. You can find everything you need and moree