Fingerprint all-in-one 2.0 Instruction Manual

Fingerprint all-in-one instructions 2.0
I. Parameters
Fingerprint all-in-one 2.0 Instruction Manual  & troubleshooting 0Size: 86*86*26mm
Fingerprint all-in-one 2.0 Instruction Manual  & troubleshooting 1Screen: black-white screen
Fingerprint all-in-one 2.0 Instruction Manual  & troubleshooting 2Fingerprint identification time: <1.5S
Fingerprint all-in-one 2.0 Instruction Manual  & troubleshooting 3False reject rate: < 0.01%
Fingerprint all-in-one 2.0 Instruction Manual  & troubleshooting 4False accept rate: < 0.0001%
Fingerprint all-in-one 2.0 Instruction Manual  & troubleshooting 5Fingerprint count: 500
Fingerprint all-in-one 2.0 Instruction Manual  & troubleshooting 6Card count: 500 (non-standard)
Fingerprint all-in-one 2.0 Instruction Manual  & troubleshooting 7Code count: 2
Fingerprint all-in-one 2.0 Instruction Manual  & troubleshooting 8Door controlled: 1
Fingerprint all-in-one 2.0 Instruction Manual  & troubleshooting 9Pass mode: fingerprint/card/code, fingerprint & card, fingerprint & code
Fingerprint all-in-one 2.0 Instruction Manual  & troubleshooting 10Linking mode: Offline
II.Operations
Fingerprint all-in-one 2.0 Instruction Manual  & troubleshooting 11TIPs:

  • The “FP” in the article is short for fingerprint.
  • The “Bell” in the article means the icon of BellFingerprint all-in-one 2.0 Instruction Manual  & troubleshooting 12
  • Long press on the Bell icon for 3 seconds and enter a six-digit code (default: 888888) to enter the menu.
  • Disconnect the power supply, long-press the reset button, and switch on the power for 3 seconds then reset the menu code.
  • Each user number supports three fingerprints and one card.
  • The pass mode integrating FP and code uses randomly allocated common codes.
  • Combination password must first press the fingerprint and then code or card plus
  • Press “Bell” to confirm.
  • Press “*” to back or cancel.

Fingerprint all-in-one 2.0 Instruction Manual  & troubleshooting 13Menu operations:

Select a number to enter the corresponding menu.
1. User Add
① FP Add
Enter the user number.
If the user number has existed, switch to backup registration.
Press “Bell” to confirm .
Press on the fingerprint reader with the same finger for successive three times.
The registration will end upon a success prompt.
Continue to the adding or backup as prompted on the screen.
② Card Add
Enter the user number.
Press “Bell” to confirm and then punch the card.
The registration will end upon a success prompt.
If the card has already exists, replace it or exit as prompted..
2. Common code
There should be two common code at most.
Enter “1”, press “Bell” to confirm, enter a six-digit common code
and press “Bell” again to confirm.
There will be a prompt of successful saving.
The same operation to register ‘2’
3. Opening Delay
Enter the delay time (maximum: 255s) and press “Bell” to confirm.
4. Time Set
Enter the Specific dateas prompted, press “Bell” to confirm and go to the next line,
Press“*” to return and save.
5. Pass mode
① FP/Card/Code
② FP&Card
③ FP& Code
Enter the corresponding digit and save it.
6. Menu Code
Enter a six-digit code and press “Bell” to confirm.
There will be a prompt of successful saving.
7. User delete
① Number Delete
Enter the user number and press “Bell” to confirm
② ALL Delete
Press “Bell” for four times to confirm.
8. Initialize
Press “Bell” four times to confirm the operation
9.Language
Press“Bell”to confirm to Chinese.
III. Wiring (Installation standards according to Standard for mounting of type 86 base)

Fingerprint all-in-one 2.0 Instruction Manual  & troubleshooting 14

Fingerprint all-in-one 2.0 Instruction Manual – Download [optimized]
Fingerprint all-in-one 2.0 Instruction Manual – Download

FAQ


Setting up Fingerprint all-in-one 2.0 Instruction Manual is easy with these step-by-step instructions. Follow the steps are you are set-up in no time.

Using Fingerprint all-in-one 2.0 Instruction Manual is simple by using this manual. Follow the instructions one by one and everything will be fine

Is Fingerprint all-in-one 2.0 Instruction Manual stuck or not working properly? By resetting it you can set it back to the standard settings and everything should be back to normal. This works in many cases when problems arise.

This page contains the complete user instructions & manual for Fingerprint all-in-one 2.0 Instruction Manual

All symbols, colors and codes for Fingerprint all-in-one 2.0 Instruction Manual are explained in this instruction manual. You can find everything you need and moree