GLP impression X4 XL Long Distance Moving LED Stage Light Instruction Manual
Description of Device
- Moving head (actively and passively cooled)
- Arm with various cooling vents
- LCD-Display/Menu (data entry)
- Base with various connectors and Camlock mounting system
- DMX- Output (5 pin)
- DMX- Output (3 pin)
- Micro-fuse: 5 x 20mm, T12A
- Power Switch
- Neutrik Powercon (Mains power input)
- Blank panel (primed for Ethernet)
- DMX- Input (3 pin)
- DMX- Input (5 pin)
- 2x Safety wire points
Note: Only connect one cable to the
DMX Input / Output at the same time
Safety Instructions
| The IMPRESSION X4 XL is a High-Tech Product. To guarantee a smooth operation, it is necessary to respect the following rules. The manufacturer of this device will not take responsibility for damages through any disregard of the information provided in this manual. Warranty claims also will be voided in the case that the fixture housing is opened. |
| Never look directly into the beam of light or into one of the LEDs. Attention: LED Class 2M can cause injuries of your eyes even without optical instruments in front of them or within a distance of less than 0.5m and short exposure time. Hence: Avoid direct radiation into your eyes! |
| WARNING: Never let optical parts come in contact with alcohol, solvents or similar cleaners. |
- Before powering on the fixture, make sure that the fixtures fans and air inlets are clean and not blocked.
- Ensure that the fixture head can rotate unhindered throughout its complete range of pan and tilt movement. A safety distance of at least 0.5 m must be maintained between the fixture and any easily inflammable material.
- Attention! Don’t touch the fixture during the operation. This can cause injuries and/or damages.
- The fixture doesn’t contain any user serviceable parts. Opening the fixture will void all warranties.
- It is necessary to wait at least 15 minutes after disconnecting the mains power before handling the fixture. Pay attention to possible hot parts.
- To ensure safe operation, follow also the Installation guide described in the chapter below. Operating the IMPRESSION X4 XL without suitable safety aids like Safety cables or clamps/hooks can increase the risk of an accident and must be avoided.
- Repair, maintenance, and installation work shall be done by qualified or GLP certified staff only. You need to pay attention to the common rules of technology that are not explicitly mentioned in this manual.
- Use only original GLP spare parts. Any structural modification of the system will terminate all warranty claims.
- Please keep this instruction manual for future reference.
Important Safety Information
The IMPRESSION X4XL fixture from GLP is fitted with a number of planoconvex lenses in a highly efficient collimator cluster. This type of lens can act as a strong magnifying glass.
If the rays from a strong light source (such as the sun or another lighting fixture) are directed towards the front of any of these fixtures, then internal damae may occur. In a worst case scenario with a high power light source this can happen very quickly, damaging the fixture internally, potentially melting components or causing an internal fire within seconds.
In order to avoid these possible problems please adhere to the following
requirements:
- Do not expose the front of a fixture to direct sunlight or any other strong light sources.
- For outdoor applications during daylight make sure that the front face of any fixture is either shielded or points away from the sun, even when fixtures are not in use.
- Do not modify the front glass or lenses of any fixture.
These requirements have to be followed regardless of whether a fixture is powered on or off as the magnifying effect is an optical effect and therefore independent from the (electrical) state of the fixture.
Especially when working with high powered beam-lights; extreme caution and observance of these safety instructions is mandatory.
Should you have any questions about the operation of your fixture then please contact your local GLP office, or their authorized distributor, a list of which can be found at www.glp.de.
Mounting
The IMPRESSION X4XL is fully operational whether it hangs or is mounted to the wall. It can also be operated while standing on the floor. Keep a safety distance of min. 0.5 m towards any easily inflammable materials (decoration etc.).
Pay attention to the regulations of: BGV C1 (former VBG 70) and DIN VDE 0711-217.
The installation shall be done by qualified staff only.
For the various mounting positions of the IMPRESSION X4XL (standing on the floor, sideways or hanging) different accessories kits are available. Through this a safe and firm installation is assured. You’ll find dedicated connectors on the bottom side of the fixture which should be used. In addition the base is marked with a FRONT arrow allowing consistent orientation during installation.
- Mounting on the Floor (upright)
To operate the IMPRESSION X4XL in an upright position, please use the dedicated tri-legged floor stand supplied with your fixture. It is fixed to the base of the fixture with fasteners called Camlock quick-release connectors. Insert the two fasteners and turn each 90° to lock them. Do the opposite to release them again. On both sides you’ll find eyelets to pull though a fixing strap. This allows for additional bracing of the fixture.
- Mounting in hanging position (Head down)
To operate the IMPRESSION X4XL in a hanging position two (2) omega brackets can be mounted directly to the bottom of the base using the four (4) Camlock connectors.
Alternatively two half-couplers (clamps) can be mounted directly to the bottom side of the fixture using M10x16 mm thread bolts.
Attention: Never use a longer bolt as this may damage the interior of the fixture.
- Securing the Fixture
Regardless of the mounting method of the IMPRESSION X4XL you’ll have to use a stipulated safety wire. Attach the safety wire through one of the two holes provided on the base of the fixture and connect it to the primary support structure. Pay attention to a safe and proper fastening. The safety cable must comply with EN 60598-2-17 Section 17.6.6 and be capable of bearing a static suspended load that is ten times the weight of the fixture and all installed accessories. - Connections
- Power Supply
~100-240 Volt AC, 50-60 Hz, earth contact type plug – Powercon Connected load 1200 VA (W) <=> T12A (micro-fuse 5x20mm)
Please see printing on the case for the right electronic supply!
Disconnect from the mains supply for changing the fuse and use only the above described micro-fuse type. - DMX
USITT DMX-512 Standard input/output in 3/5 pin connectors.
Pin 1 = [Ground] / Pin 2 = [-] / Pin 3 = [+] / Pin 4&5 N.C.
The DMX- Addressing starts at the DMX- Address [001].
- Power Supply
You’ll find the control board on the side part of the arm. It allows you to make all necessary adjustments of the IMPRESSION X4XL. With the Mode-key you get into the main menu. Afterwards you can navigate through the menu with the Up/Down-keys. Push the Enter-key to get in the next menu level or to confirm your settings. Make them and set functions ON/OFF with the Up/Down-keys. Confirm and save it with the Enter-key (the display shows OK). Push the Mode-key to cancel the entry and go back to the main menu.
To lock or unlock the keys of the menu field press Mode+Enter+Up simultaneously.
MODE – ENTER
DOWN – UP
| Level1 | Level 2 | Level 3 | Level 4 | Remark |
| DMX Start Address 001 | Set the DMX start address | |||
| Special | Manual DMX | Manual control of all fixture functions | ||
| Pan | Manual control for Pan (X-movement) | |||
| Pattern Byte 3 | Manual control for Pattern Byte 3 LED 17 -19 | |||
| Pattern Byte 2 | Manual control for Pattern Byte 2 LED 9 – 16 | |||
| Pattern Byte 1 | Manual control for Pattern Byte 1 LED 1 – 8 | |||
| Pattern | Manual control for Pattern channel / bank | |||
| Zoom | Manual control for Zoom | |||
| Speed Movements | Manual control for Pan/Tilt movements | |||
| Pan/Tilt Movements | Manual control for Pan/Tilt movements | |||
| Special | ||||
| White Temperature | Manual control for Color temperature | |||
| Dimmer | Manual control for Dimmer | |||
| Shutter | Manual control for Shutter | |||
| White | Manual control for White | |||
| Blue | Manual control for blue | |||
| Green | Manual control for green | |||
|
Manual control for red | |||
| Color Wheel | Manual control for the color wheel | |||
| Tilt | Manual control for Tilt (Y-movement) | |||
| Adjust | ||||
| Key code xxxx | Use the code for entering the calibration menu (for authorized persons only) | |||
| Display Contrast | Adjustment for the Display contrast | |||
| PWM – | Changes PMW frequency | |||
| Frequ. Adj. | ||||
| Pan Offset | Calibration for Pan-Offset | |||
| Tilt Offset | Calibration for Tilt-Offset | |||
| LED adjust | ||||
| White adjust red | Adjust intensity for red channel | |||
| White adjust blue | Adjust intensity for blue channel | |||
| White adjust green | Adjust intensity for green channel | |||
| Clear EEPROM | Erase EEPROM memory | |||
| Diagnose | Diagnose fixture functions | |||
| DMX Image | ||||
| Set image if DMX off | Activates a stored scene if DMX is off | |||
| Save image in memory | Stores the scene currently sent to the unit | |||
| DMX input Monitor | Indicates the presently received DMX signal per DMX channel | |||
| Pan | Instantaneous value for Pan | |||
| Tilt | Instantaneous value for Tilt | |||
| Pattern Byte 3 | Instantaneous value for Pattern Byte 3 | |||
| Pattern Byte 2 | Instantaneous value for Pattern Byte 2 | |||
| Pattern Byte 1 | Instantaneous value for Pattern Byte 1 | |||
| Pattern | Instantaneous value for Pattern channel / bank | |||
| Zoom | Instantaneous value for Zoom | |||
| Speed Movements | Speed adjustment for Pan/Tilt movements à | |||
| Pan/Tilt Movements | see item below | |||
| Special | Instantaneous value for Pan/Tilt movements | |||
| White Temperature | Instantaneous value for Special | |||
| Dimmer | Adjustment of the color temperature for WHITE | |||
| Shutter | Instantaneous value for Dimmer | |||
| White | Instantaneous value for Shutter | |||
| Blue | Instantaneous value for White | |||
| Green | Instantaneous value for Blue | |||
| Red | Instantaneous value for Green | |||
| Color Wheel | Instantaneous value for Red | |||
| Set DMX Mode | Instantaneous value for Color Mixing unit | |||
| Select the desired DMX Mode | ||||
| Compressed Mode | Fixture works in “Compressed” mode à see also section 5 below | |||
| Normal Mode | Fixture works in “Normal” mode à see also section 5 below | |||
| High-Res.Mode | Fixture works in “High Resolution” mode à see also section 5 below | |||
| Position feedback | Switch automatic position feedback ON/OFF | |||
| Reverse Pan | Invert Pan movements: ON/OFF | |||
| Reverse Tilt | Invert Tilt movements: ON/OFF | |||
| Reset | RESET and new calibration for all functions | |||
DMX Channel Selection (DMX Protocol)
- Normal-Mode (26 DMX channels)
Channel Function Time and Value DMX HEX % 1) PAN High Pan coarse 0° – 643° 0..255 00..FF 0..100 2) PAN Low Pan fine 0..255 00..FF 0..100 3) Tilt High Tilt coarse 0° – 295° 0..255 00..FF 0..100 4) Tilt Low Tilt fine 0..255 00..FF 0..100 5) Color (fixed) Colors adjustable via RGB 0..7 00..07 0..2..5 Color 01 – Red 1) 8..15 08..0F 3..5.5 Color 02 – Amber 1) 16..23 10..17 6..8.5 Color 03 – Warm Yellow 1) 24..31 18..1F 9..12.5 Color 04 – Yellow 1) 32..39 20..27 13..15.5 Color 05 – Green 1) 40..47 28..2F 16..18.5 Color 06 – Turquoise 1) 48..55 30..37 19..21.5 Color 07 – Cyan 1) 56..63 38..3F 22..24.5 Color 08 – Blue 1) 64..71 40..47 25..27.5 Color 09 – Lavender 1) 72..79 48..4F 28..30.5 Color 10 – Malve 1) 80..87 50..57 31..34.5 Color 11 – Magenta 1) 88..95 58..5F 35..37.5 Color 12 – Pink 1) 96..103 60..67 38..40.5 White – CTO 3200K 104..111 68..6F 41..43.5 White 5600K 112..119 70..77 44..46.5 White – CTB 7200K 120..127 78..7F 47..49.5 Rainbow Effect Stop 2) 128 80 50 Rainbow Effect 3) slow – fast 129..223 81..DF 51..88 Random colors slow – fast 224..255 E0..FF 89..100 6) Red Color mixing system – Red 0 – 100% 0..255 00..FF 0..100 7) Green Color mixing system – Green 0 – 100% 0..255 00..FF 0..100 8) Blue Color mixing system – Blue 0 – 100% 0..255 00..FF 0..100 9) White Color mixing system – White 0 – 100% 0..255 00..FF 0..100 10) Shutter Shutter closed 0..15 00..0F 0..5.5 Shutter pulse random slow – fast 16..47 10..2F 6..18.5 Fade on, snap off (random patterns) slow – fast 48..79 30..4F 19..31 Snap on, fade off (random patterns) slow – fast 80..111 50..6F 32..43 Fade on, fade off (random patterns) slow – fast 112..143 70..8F 44..56 Strobe random 5s – 0.1s 144..199 90..C7 57..77 Strobe effect slow – fast 1 Hz – 10 Hz 200..239 C8..EF 78..94 Shutter open 240..255 F0..FF 95..100 11) Dimmer Intensity 0 – 100% 0..255 0..FF 0..100 12) CTO No CTO 0..7 0..07 0..2.5 Continuous color temperature correction
Applicable for ALL colors
8..255 08..FF 3..100 13) Special Pattern Block 1 à See channel 17 0..3 00..03 0..1 Pattern Block 2 à See channel 17 4..7 04..07 2..3 Pattern Block 3 à See channel 17 8..11 08..0B 3..4 Pattern Block 4 à See channel 17 12..15 0C..0F 5..6 Pattern Block 5 à See channel 17 16..19 10..13 6..7 Pattern Block 6 à See channel 17 20..23 14..17 8..9 Pattern Block 7 à See channel 17 24..27 18..1B 9..10 Pattern Block 8 à See channel 17 28..31 1C..1F 11..12 Pattern Block 9 à See channel 17 32..35 20..23 12..13 Pattern Block 10 à See channel 17 36..39 24..27 14..15 Channel Function Time and Value DMX HEX % Enable Animation 80..83 50..53 31..32 à use channel 17 to select à use channel 18 so set step
à use channel 19 to start / for speed
Set Dimmer to soft mode 84..87 54..57 33..34 Change PWM frequency 100..200 64..C8 40..78 Set Maximum Zoom to 247 > 1 sec 208..211 D0..D3 82..83 Set Maximum Zoom to 255 > 1 sec 212..215 D4..D7 84..85 Set Zoom to normal > 1 sec 216..219 D8..DB 85..86 Set Zoom to inverted > 1 sec 220..223 DC..DF 86..87 RESET > 1 sec 250..255 FA..FF 98..100 14) Move- ment macros
No macros 0 00 0 Movement Size Phase Use “Speed” to adjust PAN 1 0° 01..01 01..01 0.5 1 90° 02..03 02..03 1.0 1 180° 04..05 04..05 1.7 1 270° 06..07 06..07 2.5 PAN 2 0° 08..09 08..09 3.3 2 90° 10..11 0A..0B 4.1 2 180° 12..13 0C..0D 4.9 2 270° 14..15 0E..0F 5.7 PAN 3 0° 16..17 11..11 6.5 3 90° 18..19 12..13 7.3 3 180° 20..21 14..15 8.0 3 270° 22..23 16..17 8.8 PAN 4 0° 24..25 18..19 9.6 4 90° 26..27 1A..1B 10.4 4 180° 28..29 1C..1D 11.2 4 270° 30..31 1E..1F 12 TILT size / phase see PAN 32..63 20..3F 13..25 PAN / TILT size / phase see PAN 64..95 40..5F 26..37 PAN / TILT (inverse) size / phase see PAN 96..127 60..7F 38..50 Circle size / phase see PAN 128..159 80..9F 51..62 Circle (inverse) size / phase see PAN 160..191 A0..BF 63..75 Lying eight size / phase see PAN 193..223 C0..DF 76..87 Random movement size / phase see PAN 224..255 E0..FF 88..100 15) Pan / Tilt Speed Pan/Tilt movement speed from controller 0..1 00..01 0..0..5 Pan/Tilt, slow – fast Use this channel for the speed of the macros on channel 14.
02..255
02..FF
1..100
16) Zoom Wide (flood) – narrow (spot) 50° – 7° 0…255 00…FF 0…100 17) Pattern / Animation No pattern 0..2 00..02 0..1 Pre-defined patterns / animations 4)5) See Special Channel 13 03..253 03..FD 2..99 Activates direct access to LED Lenses See Channel 18 – 26 254..255 FE..FF 100 18) Pattern Section 1 4) Direct activation of lenses 1 thru 8 4) Activation in binary style 0…255 00…FF 0…100 19) Pattern Section 2 5) Direct activation of lenses 9 thru 16 5) Activation in binary style 0…255 00…FF 0…100 20) Pattern Section 3 Direct activation of lenses 17 thru 19 Activation in binary style 0…255 00…FF 0…100 21) Pattern Section 4 Direct activation of lenses 20 thru 27 Activation in binary style 0…255 00…FF 0…100 Channel Function Time and Value DMX HEX % 22) Pattern Section 5 Direct activation of lenses 28 thru 35 Activation in binary style 0…255 00…FF 0…100 23) Pattern Section 6 Direct activation of lenses 36 thru 38 Activation in binary style 0…255 00…FF 0…100 24) Pattern Section 7 Direct activation of lenses 39 thru 46 Activation in binary style 0…255 00…FF 0…100 25) Pattern Section 8 Direct activation of lenses 47 thru 54 Activation in binary style 0…255 00…FF 0…100 26) Pattern Section 9 Direct activation of lens 55 Activation in binary style 0…255 00…FF 0…100 - Compress-Mode (16 DMX channels)
Channel Function Time and Value DMX HEX % 1) PAN High Pan coarse 0° – 643° 0..255 00..FF 0..100 2) PAN Low Pan fine 0..255 00..FF 0..100 3) Tilt High Tilt coarse 0° – 295° 0..255 00..FF 0..100 4) Tilt Low Tilt fine 0..255 00..FF 0..100 5) Color (fixed) Colors adjustable via RGB 0..7 00..07 0..2.5 Color 01 – Red 1) 8..15 08..0F 3..5.5 Color 02 – Amber 1) 16..23 10..17 6..8.5 Color 03 – Warm Yellow 1) 24..31 18..1F 9..12.5 Color 04 – Yellow 1) 32..39 20..27 13..15.5 Color 05 – Green 1) 40..47 28..2F 16..18.5 Color 06 – Turquoise 1) 48..55 30..37 19..21.5 Color 07 – Cyan 1) 56..63 38..3F 22..24.5 Color 08 – Blue 1) 64..71 40..47 25..27.5 Color 09 – Lavender 1) 72..79 48..4F 28..30.5 Color 10 – Mauve 1) 80..87 50..57 31..34.5 Color 11 – Magenta 1) 88..95 58..5F 35..37.5 Color 12 – Pink 1) 96..103 60..67 38..40.5 White – CTO Color temperature 3200K
104..111 68..6F 41..43.5 White Color temperature 5600K
112..119 70..77 44..46.5 White – CTB Color temperature 7200K
120..127 78..7F 47..49.5 Rainbow Effect Stop 2) 128 80 50 Rainbow Effect 3) slow – fast 129..223 81..DF 51..88 Rainbow Effect, random colors slow – fast 224.255 E0..FF 89..100 6) Red Color mixing system – Red 0 – 100% 0..255 00..FF 0..100 7) Green Color mixing system – Green 0 – 100% 0..255 00..FF 0..100 8) Blue Color mixing system – Blue 0 – 100% 0..255 00..FF 0..100 9) White Color mixing system – White 0 – 100% 0..255 00..FF 0..100 10) Shutter Shutter closed 0..15 00..0F 0..5.5 Shutter pulse random slow – fast 16..47 10..2F 6..18.5 Fade on, snap off (random patterns) slow – fast 48..79 30..4F 19..31 Snap on, fade off (random patterns) slow – fast 80..111 50..6F 32..43 Fade on, fade off (random patterns) slow – fast 112..143 70..8F 44..56 Strobe random 5s – 0.1s 144..199 90..C7 57..77 Strobe effect slow – fast 1 Hz – 10 Hz 200..239 C8..EF 78..94 Shutter open 240..255 F0..FF 95..100 11) Dimmer Intensity 0 – 100% 0..255 0..FF 0..100 12) Zoom Wide (flood) – narrow (spot) 50° – 7° 0…255 00…FF 0…100 13) Special Pattern Block 1 à See channel 14 0..3 00..03 0..1 Pattern Block 2 à See channel 14 4..7 04..07 2..3 Pattern Block 3 à See channel 14 8..11 08..0B 3..4 Pattern Block 4 à See channel 14 12..15 0C..0F 5..6 Pattern Block 5 à See channel 14 16..19 10..13 6..7 Pattern Block 6 à See channel 14 20..23 14..17 8..9 Pattern Block 7 à See channel 14 24..27 18..1B 9..10 Pattern Block 8 à See channel 14 28..31 1C..1F 11..12 Pattern Block 9 à See channel 14 32..35 20..23 12..13 Pattern Block 10 à See channel 14 36..39 24..27 14..15 Channel Function Time and Value DMX HEX % Enable Animation 80..83 50..53 31..32 à use channel 14 to select à use channel 15 so set step
à use channel 16 to start / for speed
Set Dimmer to soft mode 84..87 54..57 33..34 Change PWM frequency 100..200 64..C8 40..78 Set Maximum Zoom to 247 > 1 sec 208..211 D0..D3 82..83 Set Maximum Zoom to 255 > 1 sec 212..215 D4..D7 84..85 Set Zoom to normal > 1 sec 216..219 D8..DB 85..86 Set Zoom to inverted > 1 sec 220..223 DC..DF 86..87 RESET > 1 sec 250..255 FA..FF 98..100 14) Pattern / Animation No pattern 0..2 00..02 0..1 Pre-defined patterns / animations 4)5) See Special Channel 13 03..253 03..FD 2..99 15) A-Step 4) Animation step 4) See Special Channel 13 00..255 00..FF 0..100 16) A-Speed 5) Animation start / speed 5) See Special Channel 13 00..255 00..FF 0..100 - High Resolution/Extended-Mode (27 DMX Channels)
Channel Function Time and Value DMX HEX % 1) PAN High Pan coarse 0° – 643° 0..255 00..FF 0..100 2) PAN Low Pan fine 0..255 00..FF 0..100 3) Tilt High Tilt coarse 0° – 295° 0..255 00..FF 0..100 4) Tilt Low Tilt fine 0..255 00..FF 0..100 5) Red High Color mixing system – Red 0 – 100% 0..255 00..FF 0..100 6) Red Low Color mixing system – Red-Low 0..255 00..FF 0..100 7) Green High Color mixing system – Green 0 – 100% 0..255 00..FF 0..100 8) Green Low Color mixing system – Green-Low 0..255 00..FF 0..100 9) Blue High Color mixing system – Blue 0 – 100% 0..255 00..FF 0..100 10) Blue Low Color mixing system – Blue-Low 0..255 00..FF 0..100 11) White High Color mixing system – White 0 – 100% 0..255 00..FF 0..100 12) White Low Color mixing system – White-Low 0..255 00..FF 0..100 13) Shutter Shutter closed 0..15 00..0F 0..5.5 Shutter pulse random slow – fast 16..47 10..2F 6..18.5 Fade on, snap off (random patterns) slow – fast 48..79 30..4F 19..31 Snap on, fade off (random patterns) slow – fast 80..111 50..6F 32..43 Fade on, fade off (random patterns) slow – fast 112..143 70..8F 44..56 Strobe random 5s – 0.1s 144..199 90..C7 57..77 Strobe effect slow – fast 1 Hz – 10 Hz 200..239 C8..EF 78..94 Shutter open 240..255 F0..FF 95..100 14) Dimmer- High Intensity coarse 0 – 100% 0..255 0..FF 0..100 15) Dimmer- Low Intensity fine 0..255 0..FF 0..100 16) Zoom Wide (flood) – narrow (spot) 50° – 7° 0…255 00…FF 0…100 17) Special Pattern Block 1 à See channel 18 0..3 00..03 0..1 Pattern Block 2 à See channel 18 4..7 04..07 2..3 Pattern Block 3 à See channel 18 8..11 08..0B 3..4 Pattern Block 4 à See channel 18 12..15 0C..0F 5..6 Pattern Block 5 à See channel 18 16..19 10..13 6..7 Pattern Block 6 à See channel 18 20..23 14..17 8..9 Pattern Block 7 à See channel 18 24..27 18..1B 9..10 Pattern Block 8 à See channel 18 28..31 1C..1F 11..12 Pattern Block 9 à See channel 18 32..35 20..23 12..13 Pattern Block 10 à See channel 18 36..39 24..27 14..15 Enable Animation 80..83 50..53 31..32 à use channel 18 to select à use channel 19 so set step
à use channel 20 to start/for speed
Set Dimmer to soft mode 84..87 54..57 33..34 Change PWM frequency 100..200 64..C8 40..78 Set Maximum Zoom to 247 > 1 sec 208..211 D0..D3 82..83 Set Maximum Zoom to 255 > 1 sec 212..215 D4..D7 84..85 Set Zoom to normal > 1 sec 216..219 D8..DB 85..86 Set Zoom to inverted > 1 sec 220..223 DC..DF 86..87 RESET > 1 sec 250..255 FA..FF 98..100 18) Pattern No pattern 0..2 00..02 0..1 Pre-defined patterns / animations 4)5) See Special Channel 17 03..253 03..FD 2..99 Activates direct access to LED Lenses
254..255 FE..FF 100 19) Pattern Section 1 4) Direct activation of lenses 1 thru 8 4) Activation in binary style 0…255 00…FF 0…100 Channel Function Time and Value DMX HEX % 20) Pattern Section 2 5) Direct activation of lenses 9 thru 16 5) Activation in binary style 0…255 00…FF 0…100 21) Pattern Section 3 Direct activation of lenses 17 thru 19 Activation in binary style 0…255 00…FF 0…100 22) Pattern Section 4 Direct activation of lenses 20 thru 27 Activation in binary style 0…255 00…FF 0…100 23) Pattern Section 5 Direct activation of lenses 28 thru 35 Activation in binary style 0…255 00…FF 0…100 24) Pattern Section 6 Direct activation of lenses 36 thru 38 Activation in binary style 0…255 00…FF 0…100 25) Pattern Section 7 Direct activation of lenses 39 thru 46 Activation in binary style 0…255 00…FF 0…100 26) Pattern Section 8 Direct activation of lenses 47 thru 54 Activation in binary style 0…255 00…FF 0…100 27) Pattern Section 9 Direct activation of lens 55 Activation in binary style 0…255 00…FF 0…100 - The predefined colors can be used as start-colors for the Rainbow effect. Please select first a desired start-color before you activate the rainbow effect. All IMPRESSION X4XL will then start from that color and will execute the rainbow effect synchronously. Different IMPRESSION X4XL can have different start-colors but will still execute the rainbow effect synchronously. If you choose a color different from the ones marked with 1) in the tables above the rainbow start-color will be red.
- Rainbow-effect Stop will pause this function. After resuming the rainbow-effect will be continued from the current color.
- The Rainbow-effect will run synchronously only if started from one of the predefined colors (see also 1) before).
- If the Animation mode is activated through Special Channel set to DMX = 80..83 then the Function of this Channel is:
Animation step 00..255 00..FF 0..100 Use this Chanel to select the starting point of the animation.
- If the Animation mode is activated through Special Channel set to DMX = 80..83 then the Function of this Channel is:
Animation start / speed 00..255 00..FF 0..100
Locking and unlocking the Control Panel
Please lock and unlock the control panel by pressing the menu keys MODE & ENTER & UP at the
same time.
Additional Display Indications
As a default you’ll find the following additional information in the first row of the LCD display:
Vxx/xx/xx/xx/x
N = Normal Mode / C = Compressed Mode / H = High Res. Mode
N = Tilt normal / I = Tilt inverted
N = Pan normal / I = Pan inverted
LED driver version
Main CPU version
Maintaining and Cleaning
The IMPRESSION X4XL is a fixture of very low maintenance. It is only necessary to clean the air inlets and outlets as well as the optical LED lenses from time to time. For safe operation it is absolutely essential that the fixture is kept clean and that dust, dirt and smoke-fluid residues must not build up on, or within the fixture. Otherwise the fixture’s light-output will be significantly reduced or damages can occur. Regular cleaning will not only ensure the maximum light-output, but will also allow the fixture to operate reliably throughout its life.
A soft lint-free cloth moistened with any good glass cleaning fluid is recommended to clean the lenses.
Attention:
Under no circumstances should alcohol or solvents be used to clean the lenses!
- Safety regulations
- Pull out the mains power plug!
- Wait min. 15 minutes after disconnecting power to allow the fixture to cool down.
- Maintenance and Interval (rule-of-thumb)
The contamination of the fixture depends on the environment details. Hence no general guidelines can be given. The intervals given below are only suggestions from our experience.
Position Interval In this way LED reflector and optical system weekly soft brush /lint-free cloth Fan and air channel monthly vacuum cleaner, airbrush, etc.
Attention:
- Never let optical parts come into contact with oil, fat, alcohol or similar solvents.
- Before running the fixture wait until all parts are dry.
- Never touch lenses with bare fingers.
Technical Specifications
| Power supply | |
| Power consumption | 1200 VA (Watt) |
| Power Input | ~100-240 V AC, 50-60 Hz (wide range input) |
| Fuse protection | Micro-fuse 5×20 mm, T12A |
| Operational Parameters | |
| Max. Ambient Temperature | 5° – 45°C (integrated overheating switch) |
| Mounting Position | Any (see relevant chapter) |
| Lighting System – Additive Color mixing | |
| LED Type | 55 x Osram Ostar RGBW multi-chip |
| Lifetime | 50,000 h |
| Wavelength optimized for maximum presentable color space | |
| Optical System | |
| Full RGBW / High efficient Collimator cluster | |
| Shutter / Dimmer (8/16 Bit) | |
| Strobe- Effect with variable speed between 1 – 10 flashes per second, Random-Strobe, Pulse- Effects | |
| Continuous Dimmer 0 – 100% | |
| Zoom | |
| 7 to 50 degree continuous zoom | |
| Optical Patterns | |
| Several hundred pre-defined beam patterns with direct access and manipulation | |
| DMX Control | |
| Standard USITT DMX-512, 3/5 pin XLR: [+]=Pin 3 / [-]=Pin 2 / [Ground]=Pin 1 / Pin 4&5 N.C. The DMX- Addressing starts at the DMX channel [001]. | |
| Pan / Tilt (8/16 Bit) | |
| Pan- movement | 643° in min. 3,2 seconds (Position Feedback) |
| Tilt- movement | 295° in min. 1,5 seconds (Position Feedback) |
| Weights and Measures | |
| Width of the base | 521 mm |
| Length of the base | 361 mm |
| height (head vertical) | 519 mm (incl. standing foot/tripod) |
| Weight (net) | 31.0 kg |
Dimensions
Tilt range: 295°
Pan range: 643°
