HENDUN Waterproof Gate Door Alarm User Guide

HENDUN Waterproof Gate Door Alarm User Guide & troubleshooting

Waterproof Gate/Door AlarmHENDUN Waterproof Gate Door Alarm User Guide  & troubleshooting 1

USER GUIDE

Key Features

  •  IP67 waterproof
  •  Two methods of operation: key-pad and remote control
  •  Super-high sound: 140 db.
  • Multiple alarm modes

1. Description of Structure
1.1 host and magnetic box

HENDUN Waterproof Gate Door Alarm User Guide  & troubleshooting 2

1.2 remote control

HENDUN Waterproof Gate Door Alarm User Guide  & troubleshooting 3

2. Password setting and recovery
Original password: 1234

Change password:

Step 1: Enter the Original password 1234, a beep sound;
Step 2: Long press the button “ ①”, a red light appears
Step 3: Enter your new password, long press button “ ①”, red light flash 3 times means change successfully; If continuous beep sound means to change the password, not a success, repeat the above steps.

Factory Reset:

Press the button “ ①” and button “ ②” at the same time until there is a beep sound.

Note: The password cannot be changed via the remote control.

3. Function setting
3.1 Set by key-pad

Situation Operation

Function

Alarm mode

Enter the password 1234 “, a beep sound; press the button ” 1;”, a red light appears, Alarm mode set successfully. Alarm mode: When the door is opened without a password, the alarm is activated, close the door, alarm stops.

Disarm mode

Enter the password 1234 “, a beep sound, disarm mode set successfully. Disarm mode: enter the password to exit from alarm mode.

Delay 15 seconds alarm mode

Enter the password 1234 “, a beep sound; press the button ” 2 “, red light appears, Delay 15 seconds alarm mode set successfully. Open the door for 15s, alarm activated; close the door in 15s, the alarm won’t be activated.

Chime mode

Enter the password 1234 “, a beep sound, press the button
” 3 ” red light appears, doorbell mode set successfully.
Open the door, Ding-dong sound; close the door, stop.

30s alarm mode

Enter the password      1234 “, a beep sound, press the button ” 4;”, a red light appears, 30s alarm mode set successfully. Open the door, alarm 30s.

3.2 Set by remote control
3.2.1 Programming a new remote
The remote control is factory programmed; however, if you need to program a new remote please follow: Enter your chosen 4-digit code on the key-pad and press button ②  for 3 seconds until the red LED light comes on now press any button on the remote control, you will hear 1 beep. Your remote has now been programmed.
3.2.2 Delete the programmed remote control Enter your chosen 4-digit code on the key-pad and press button ② for 6 seconds, the red LED light will flash 3 times, you will hear 1 beep, all the programmed remote controls are removed.
3.2.3 Different mode settings

Situation Operation Function
immediate
alarm mode
HENDUN Waterproof Gate Door Alarm User Guide  & troubleshooting 4
When you press, you will hear 1-4 beep(s), representing different modes. press, you will be in different modes. press again loops in turn to the next mode. 
continuous alarm immediately  when the door is opened unless  close the door or press
Delay 15s
alarm mode
alarm for 30s after the door is  opened 15s; close the door in  15s or press , alarm won`t be  activated.
Chime
mode
when the door is opened, it will  make a Ding Dong sound.
immediate
30s alarm
mode
When the door is opened, the alarm sound will be stopped after 30s, press , stop sound.
SOS alarm Press SOS button , stop sound. alarm will sound  for 30s, press , stop sound.

Installation

4.1 Use 3M tape to stick it on the door or window.

HENDUN Waterproof Gate Door Alarm User Guide  & troubleshooting 5

4.2 You can also install the hook on the door and window, and then hang the host on the hook. Install the hook with the attached screw or strap.
HENDUN Waterproof Gate Door Alarm User Guide  & troubleshooting 6Note: The narrow side of the installation hole is upward, and the strap passes through two installations.
4.3 Replace the Batteries Remove the screws with a tool, install 4 pcs AAA batteries for alarm, so do as 1 pcs CR2032 battery of remote .

Parameters

Waterproof Level IP67
Application Door/Window/Gate
Material: ABS Plastic
Alarm device Weight: 170g
Decibel: 140db
Battery in alarm: 4pcs AAA (included)
Alarm device size: 124.5*74.5*29.5mm
Magnet size: 45*13*13mm
Remote size: 60*33*11mm
Remote weight: 15g
Remote control distance: 15m
Battery in remote: 1pcs CR2032 (included)
MHZ: 433.92
Working temperature: -10~60℃
Environment humidity: <90%

HENDUN Waterproof Gate Door Alarm User Guide  & troubleshooting 7

FAQ


Setting up HENDUN Waterproof Gate Door Alarm User Guide is easy with these step-by-step instructions. Follow the steps are you are set-up in no time.

Using HENDUN Waterproof Gate Door Alarm User Guide is simple by using this manual. Follow the instructions one by one and everything will be fine

Is HENDUN Waterproof Gate Door Alarm User Guide stuck or not working properly? By resetting it you can set it back to the standard settings and everything should be back to normal. This works in many cases when problems arise.

This page contains the complete user instructions & manual for HENDUN Waterproof Gate Door Alarm User Guide

All symbols, colors and codes for HENDUN Waterproof Gate Door Alarm User Guide are explained in this instruction manual. You can find everything you need and moree