HIKVISION Wireless Emergency Button User Guide

HIKVISION Wireless Emergency Button User Guide & troubleshooting

HIKVISION Wireless Emergency Button User Guide  & troubleshooting 1DS-PDEB-EG2-WE
Wireless Emergency Button

Appearance

HIKVISION Wireless Emergency Button User Guide  & troubleshooting 2

Indicator

Alarm: Flashing red indicates the alarm is triggered.
Signal Strength: In the signal strength checking mode,
Signal LED turns green for 3 s: Strong.
Signal LED turns orange for 3 s: Medium.
Signal LED turns red for 3 s: Weak.
Signal LED flashes red for 3 s: Disconnected.

TAMPER Button:
Tampering Alarm: Trigger alarm when the device is disassembled.
Formatting: Format the emergency button.

Enrollment

  1.  Log in to the APP Store, download, and install the App.
  2.  Power on the security control panel.
  3. Log in to the APP and tap the icon “+”. Scan the QR code or input the control panel serial No. to add the control panel.
  4. Log in to the APP Store, download, and install the App.
  5.  Power on the security control panel.
  6.  Log in to the APP and tap the icon “+”. Scan the QR code or input the control panel serial No. to add the control panel.

1.Enroll the Peripheral Locally

  1.  In the APP, tap the “Enrollment Mode” button on the control panel page to make the control panel enter the enrollment status.
  2. Trigger the peripheral, and it will be automatically enrolled to the control panel.

2.Enroll the Peripheral

  1. In the APP, tap the icon “+” and scan the QR code or serial No. on the peripheral.
  2. Trigger the peripheral, and it will be automatically enrolled to the control panel.HIKVISION Wireless Emergency Button User Guide  & troubleshooting 3

Installation

Check signal strength
Enter the signal checking mode by operating on the control panel.
Solid green for 3 s: Strong signal.
Solid orange for 3 s: Medium signal.
Solid red for 3 s: Weak signal.
Red flashes for 3 s: Lost signal.

HIKVISION Wireless Emergency Button User Guide  & troubleshooting 4

Install the panic button
1.Installation with Sponge Tape

  1.  Paste the sponge tape on the rear panel.
  2.  Paste the rear panel on the required place.HIKVISION Wireless Emergency Button User Guide  & troubleshooting 5 Note: Non-EN compliant after Installation with Sponge Tape

CAUTION
IF THE BATTERY COMPARTMENT DOES NOT CLOSE SECURELY, STOP USING THE  PRODUCT  AND KEEP IT AWAY FROM CHILDREN.

2.Installation with Screw

  1. Insert and rotate the screwdriver in the groove to disassemble the device.
  2. Secure the device to the wall with two screws through the holes in the rear panel.
  3. Align the front panel and the rear panel and buckle them together.

HIKVISION Wireless Emergency Button User Guide  & troubleshooting 6

Test

Trigger the emergency button, and the LED indicates the operation result.

  1. Button
  2. Alarm Received

HIKVISION Wireless Emergency Button User Guide  & troubleshooting 7

REPLACE BATTERY

  1. Insert and rotate the screwdriver in the groove to disassemble the device.
  2.  Replace the battery.

HIKVISION Wireless Emergency Button User Guide  & troubleshooting 8

CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
REPLACEMENT OF A BATTERY WITH AN INCORRECT TYPE CAN DEFEAT A  SAFEGUARD.

CAUTION
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS AND LOCAL REGULATIONS.
CAUTION
CHEMICAL BURNING DANGER DOES NOT SWALLOW THE BATTERY KEEP NEW AND USED BATTERIES AWAY FROM THE  CHILDREN. IF YOU THINK BATTERIES MIGHT HAVE BEEN  SWALLOWED OR PLACED INSIDE ANY PART OF  THE BODY, SEEK IMMEDIATE MEDICAL  ATTENTION.

Function

Function

Description

Panic Alarm Press the button to trigger the alarm while in an emergency condition. The LED keeps red for 2 s.
Medical Alarm Set the panic button as a medical button via the AX PRO client. Press the button to trigger the alarm while in an emergency condition. The LED keeps red for 2 s.
Panic Alarm Press the two buttons synchronously to trigger the alarm while in emergency conditions. The LED keeps red for 2 s.
Medical Alarm Set the panic button as a medical button via the AX PRO client. Press the two buttons synchronously to trigger the alarm while in emergency conditions. The LED keeps red for 2 s.

Formatting

Remove the battery. Hold the tamper button and meanwhile power the device on at the same time. The red LED flashes 3 times when the formatting is completed.

Set-Up with App

You can view the device status including temperature, signal intensity, battery level, connection, 24-hour zone, and operation mode on the device page.
Tap the button to enter the settings page.

Function

Description

Zone Type Select the zone type of the detector
Enable Silent Zone Slide to green to make the zone keep silent while the alarm is triggered.
Cross Zone If the alarm is triggered in both of the linked zones within the set time, two-alarm messages will be reported.
Link Camera Link with a camera for intruder verification.
Polling Rate Set the interval of a heartbeat.
Signal Strength Test Enter the test mode, and view the LED indication.

Operation Caution and Device Maintenance

  • All the electronic operations should be strict in compliance with the electrical safety regulations, fire prevention regulations, and other related regulations in your local region.
  •  Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment installation on vibrations surfaces or places subject to shock (ignorance can cause equipment damage).
  • Please make sure that the power has been disconnected before you wire, install or dismantle the device.
  • If smoke, odors, or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center.
  • Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment installation on vibrations surfaces or places subject to shock (ignorance can cause equipment damage).
  • Do not place the device in extremely hot (refer to the specification of the device for the detailed operation temperature), cold, dusty or damp locations, and do not expose it to high electromagnetic radiation.
  • The device for indoor use shall be kept from rain and moisture.
    Exposing the equipment to direct sunlight, low ventilation or heat source such as heater or radiator is forbidden (ignorance can cause fire danger).
  • Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a malfunction, however), and affecting the endurance of the sensor at the same time.
  • Improper use or replacement of the battery may result in a hazard of explosion. Replace with the same or equivalent type only. Dispose of
    used batteries according to the instructions provided by the battery manufacturer.
  • Do not expose the device to corrosive gas. Otherwise, equipment damage may occur.
  •  Do not expose the device to an explosive situation.

Specification

LED indicator Red (alarm)
LED alarm confirmation Flashing LED
Tamper protection Front & Back
Encapsulated plastic Yes
Operating temperature •10 °C to 55°C (14 °F to 131 °F)
•10 °C to 40 °C (14 °F to 104 °F) EN Certified
Storage temperature •20 °C to 60°C (-4 °F to 140 °F)
Operating humidity 10% to 90%
Dimension (W x H x D) 63.8mm x 63.8mm x 17.9mm
Weight 45.5g
Button colour Red or green keymat
Wireless technology Tri-X Wireless Technology
Environment temperature indicator Yes
2-way wireless communication Yes
Transmission frequency 868MHz
Frequency hopping Multichannel transmission
Transmission encryption AES-128 encryption
Signal strength indicators Yes
RF range 1.2Km (Open area)
Enrolling methods Power up, Remote ID, QR code
Battery CR2450 x 1 (included) 620mAh capacity
Standard battery life 5 years
PS type Type C
Low voltage level 2.60 V
Consumption Quiescent Current: 23.02uA Max: 36.89mA
Classification Use inside the supervised premises

 

EN 50131-1:2006+A1: 2009+A2:2017
EN 50131-3:2009
EN 50131-5-3:2017
Security Grade(SG) 2
Environmental Class(EC) II
Certified by Telefication

©2020 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved.
About this Manual
The Manual includes instructions for using and managing the Product. Pictures, charts, images, and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version of this Manual at the Hikvision website (https://www.hikvision.com/).
Please use this Manual with the guidance and assistance of professionals trained in supporting the Product.

HIKVISION Wireless Emergency Button User Guide  & troubleshooting 9 and other Hikvision trademarks and logos are the properties of Hikvision in various jurisdictions. Other trademarks and logos mentioned are the properties of their respective owners.

Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL AND THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE, AND FIRMWARE, ARE PROVIDED “AS IS” AND “WITH ALL FAULTS AND ERRORS”. HIKVISION MAKES NO WARRANTIES,  EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY,  SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE  PRODUCT BY YOU IS AT YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO  YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES,  INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS  INTERRUPTION, OR LOSS OF DATA, CORRUPTION OF SYSTEMS, OR LOSS OF  DOCUMENTATION, WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING  NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN CONNECTION WITH THE USE OF  THE PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH  DAMAGES OR LOSS.

YOU ACKNOWLEDGE THAT THE NATURE OF THE INTERNET PROVIDES FOR INHERENT SECURITY RISKS, AND HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE, OR OTHER DAMAGES RESULTING FROM
CYBER-ATTACKS, HACKER ATTACKS, VIRUS INSPECTIONS, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS, AND YOU ARE SOLELY RESPONSIBLE FOR ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE LAW. ESPECIALLY, YOU ARE RESPONSIBLE, FOR USING THIS PRODUCT IN A MANNER THAT DOES NOT INFRINGE ON THE RIGHTS OF THIRD PARTIES, INCLUDING WITHOUT LIMITATION, RIGHTS OF PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA PROTECTION, AND OTHER PRIVACY RIGHTS. YOU SHALL NOT USE THIS PRODUCT FOR ANY PROHIBITED END-USES, INCLUDING THE DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATTER PREVAILS.

HIKVISION Wireless Emergency Button User Guide  & troubleshooting 10 This product and – if applicable – the supplied accessories too are marked with “CE” and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, RE Directive 2014/53/EU, the RoHS Directive 2011/65/EU.

HIKVISION Wireless Emergency Button User Guide  & troubleshooting 11 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more  information see: www.recyclethis.info

HIKVISION Wireless Emergency Button User Guide  & troubleshooting 12 replacement of a battery with an incorrect type that can defeat a safeguard (for example, in the case of some lithium battery types);
– disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion;
– leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas; and
– a battery subjected to the extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas

HIKVISION Wireless Emergency Button User Guide  & troubleshooting 13 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see:www.recyclethis.info

References

FAQ


Setting up HIKVISION Wireless Emergency Button User Guide is easy with these step-by-step instructions. Follow the steps are you are set-up in no time.

Using HIKVISION Wireless Emergency Button User Guide is simple by using this manual. Follow the instructions one by one and everything will be fine

Is HIKVISION Wireless Emergency Button User Guide stuck or not working properly? By resetting it you can set it back to the standard settings and everything should be back to normal. This works in many cases when problems arise.

This page contains the complete user instructions & manual for HIKVISION Wireless Emergency Button User Guide

All symbols, colors and codes for HIKVISION Wireless Emergency Button User Guide are explained in this instruction manual. You can find everything you need and moree