John Lewis Double Glass 5lt Flush Ceiling Light User Manual

John Lewis Double Glass 5lt Flush Ceiling Light User Manual & troubleshooting

John Lewis Double Glass 5lt Flush Ceiling Light User Manual  & troubleshooting 1User manual
Double Glass 5lt Flush
Ceiling Light

John Lewis Double Glass 5lt Flush Ceiling Light User Manual  & troubleshooting 2

Thank you for purchasing this Double Glass flush ceiling light. Please read the instructions carefully before use to ensure safe and satisfactory operations of this product. Please keep this instruction for future reference.

Warnings!
For your safety, this product must be installed in accordance with local Building Regulations.
If in any doubt, or where required by the law, consult a competent person who is registered with an electrical self-certification scheme. Further information is available online or by phone at your Local Authority.
To prevent electric shock, switch off the mains supply before installing or maintaining this product. Ensure other persons cannot restore the electricity supply without your knowledge.
Always use the correct bulb type with the correct wattage as indicated in the specification table. This product is Class I = and should be fitted to a lighting Supply protected by a 5 amp fuse or equivalent circuit breaker.
When changing the bulb, always switch off at the mains and allow the old bulb to cool down before handling. Dispose of used bulbs carefully.
Caution! The bulb and surrounding parts can become hot during use.
For indoor use only.

Care instructions

We recommend cleaning with a soft dry cloth. Do not use abrasive materials as these will damage the finish.
Replace bulb from John Lewis or established brand of the same type and compatibility.

Parts list

John Lewis Double Glass 5lt Flush Ceiling Light User Manual  & troubleshooting 3Assembly

Never install your appliance on a wet, freshly painted or plastered surface. Ensure the house electricity supply is switched off at the fuse box. If removing an existing fitting, note down all wiring connections. Check the fixings will not touch any existing wiring before drilling and attaching the light to the ceiling. Ensure you thread the ceiling wires through the black insulating tube fixed to the appliance.

Step 1
Remove mounting bracket from the fitting by removing the retaining screws and any washers, retain for later.  Using the mounting bracket as a template, mark and then drill the fixing holes in the ceiling (ensure the screws  are firmly fixed into a solid or other suitable mounting and not just the plasterboard.) Take care not to damage wiring. Attach the mounting bracket to the mounting surface using suitable fixings. Do not attach the fitting to the mounting bracket at this stage. Make sure no wires are trapped in the process.

John Lewis Double Glass 5lt Flush Ceiling Light User Manual  & troubleshooting 4Step 2
Carefully fold out the arms of the fitting until they are in the correct positions.
Ensuring that the power has been isolated, connect the electrical supply wires to the connector blocks corresponding terminals. Make the electrical connection  as follows:John Lewis Double Glass 5lt Flush Ceiling Light User Manual  & troubleshooting 5

  • Connect the supply live (normally brown or red) to fitting life (marked “L”) on the terminal block housing.
  •  Connect the supply neutral (normally blue or black) to fitting neutral (marked “N”) on the terminal block housing.
  •  Connect the supply earth (normally green/yellow or unsheathed) to earth (marked “ ”) on terminal block housing.

Ensure electrical connections are tight and no loose strands of wire protrude from the terminal block.
Please note that residential wiring can vary, if you are unsure about the correct polarity please consult a qualified electrician.

Step 3

The excess cable must be carefully located inside the ceiling cup or within the ceiling cavity itself. Carefully offer fitting over mounting bracket then secure in place with the screws and any washers removed earlier. Fit the bulb: type and wattage as indicated on the fitting.
Fit the shades by placing the threaded hole in the shade over the lamp holder section and rotating it into place. If cross-threading occurs undo and start again. Take care not to overtighten as this may cause damage to the fitting.  The wattage indicated must not be exceeded. Once installation is complete, the house electricity may be restored at the fuse box.John Lewis Double Glass 5lt Flush Ceiling Light User Manual  & troubleshooting 6

Recommended bulb

5 x 3-5 Watt G9 energy-efficient LED

Specification
Max power: 5W
Voltage: 220~240V, 50/60Hz
IP20
Weight 1.8Kg

John Lewis Double Glass 5lt Flush Ceiling Light User Manual  & troubleshooting 7

Please retain these instructions for future reference.
This symbol John Lewis Double Glass 5lt Flush Ceiling Light User Manual  & troubleshooting 8indicates that this product should not be treated as normal household waste and it should be recycled. John Lewis does not operate in-store take back, but as a member of the Distributor, the Take-Back scheme has funded the development and upgrade of recycling facilities across the UK. Please take it to your nearest collection facility or for further details contact your local council or visit www.recycle-more.co.uk.

We have taken great care to ensure that this product reaches you in perfect condition.
However, should any parts be damaged or missing please e-mail [email protected]

Troubleshooting:
Why is the light not working when switched on?
Check your power supply is switched on
Turn off the light and check that the bulb is inserted correctly
Check the bulb is still in working order.

John Lewis partnership
171 Victoria Street
London SW1E 5NN
Johnlewis.com

Made in China
Issue 1 05/20

References

FAQ


Setting up John Lewis Double Glass 5lt Flush Ceiling Light User Manual is easy with these step-by-step instructions. Follow the steps are you are set-up in no time.

Using John Lewis Double Glass 5lt Flush Ceiling Light User Manual is simple by using this manual. Follow the instructions one by one and everything will be fine

Is John Lewis Double Glass 5lt Flush Ceiling Light User Manual stuck or not working properly? By resetting it you can set it back to the standard settings and everything should be back to normal. This works in many cases when problems arise.

This page contains the complete user instructions & manual for John Lewis Double Glass 5lt Flush Ceiling Light User Manual

All symbols, colors and codes for John Lewis Double Glass 5lt Flush Ceiling Light User Manual are explained in this instruction manual. You can find everything you need and moree