KRAMER DSP-62-UC 2xHDMI to HDBaseT Switcher
DSP-62-UC Quick Start Guide
This guide helps you install and use your DSP-62-UC for the first time. Go to www.kramerav.com/downloads/DSP-62-UC to download the latest user manual and check if firmware upgrades are available.
Check what’s in the box
- DSP-62-UC Digital Sound Processor
- 4 Rubber feet 1
- Quick start guide
- Power adapter and cord 2
- Bracket sets
Get to know your DSP-62-UC
| # | Feature | Function | |
|
1 |
SETUP DIP-switches | Do not change DIP-switch settings (not for use)!
DIP-switches 1 and 2 are always set to ON (down) and DIP-switches 3 and 4 are always set to OFF (up). |
|
| 2 | HDMI IN 1 Button | Press to select HDMI IN 1 input (on the front panel). | |
| 3 | HDMI IN 2 Button | Press to select HDMI IN 2 input (on the rear panel). | |
| 4 | AUDIO LEDs | USB IN | Lights green when an audio source is received from the USB host port. |
| USB OUT | Lights green when an audio signal is sent to the USB host port. | ||
| 5 | IN (1 to 5) | Lights green when a signal is present, lights red when clipping is detected. For IN 2 to IN 5, when connecting a microphone and setting to Mic mode via the embedded web pages, lights blue. | |
| OUT 1 | Lights green when a signal is present, lights red when clipping is detected. | ||
| 6 | AUDIO IN 1 3.5mm Mini Jack | Connect to an unbalanced audio source. | |
| 7 | USB Type B Bi-directional Host Port | Connect to an audio source or acceptor. | |
| 8 | HDMI IN 1 Connector | Connect to an HDMI source. | |
| 9 | LINK LED | Lights green when a link with the receiver is established. | |
| 10 | ON LED | Lights green when the device is powered by power supply. Lights blue when provides PoE (PSE).
Lights orange when powered by PoE (PD). |
|
| 11 | HDMI IN 2 Connector | Connect to an HDMI source. | |
| 12 | HDBT OUT Connector with POE (PD & PSE) | Connect to an HDBT receiver. | |
| 13 | AUDIO IN 3-pin Terminal Block Connectors (2 to 5) | Connect to up to 4 mono balanced audio sources (mono or mic level with selectable 48V). | |
| 14 | AUDIO OUT 5-pin Terminal Block Connector | Connect to a stereo balanced audio acceptor. | |
| 15 | I/O Terminal Block Connectors (1 to 2) | Connect to up to two sensors, switches, LEDs, or relays. | |
| 16 | RS-232 (G, Rx, Tx) Terminal Block Connector | Connect to a PC/serial controller | |
| 17 | ETHERNET RJ-45 Connector | Connect to a PC via a LAN. | |
| 18 | RESET Recessed Button | Press and hold while powering the device to reset to factory default values, including IP settings. | |
| 19 | 48V DC Power Connector | Connect to the power supply and to the mains electricity. | |
Mount DSP-62-UC
Install DSP-62-UC using one of the following methods:
- Attach the rubber feet and place the unit on a flat surface.
- Fasten a bracket (included) on each side of the unit and attach it to a flat surface (see www.kramerav.com/downloads/DSP-62-UC).
- Mount the unit in a rack using the recommended rack adapter (see www.kramerav.com/product/DSP-62-UC).
- Mount the unit in a Kramer Table-Mount unit (see www.kramerav.com/product/DSP-62-UC).
Connect inputs and outputs
Connecting the audio output
- To a balanced stereo audio acceptor
- To an unbalanced stereo audio acceptor
Connect power
Connect the 48V DC power cord to DSP-62-UC and plug it into the mains electricity (unless powered by PoE). Safety Instructions (See www.kramerav.com for updated safety information)
Caution:
- For products with relay terminals and GPIO ports, please refer to the permitted rating for an external connection, located next to the terminal or in the User Manual.
- There are no operator serviceable parts inside the unit.
Warning: - Use only the power cord that is supplied with the unit.
- Disconnect the power and unplug the unit from the wall before installing.
Operate the DSP-62-UC
Operate DSP-62-UC via:
- Embedded web pages via the Ethernet.
- RS-232 serial commands are transmitted by a touch screen system, PC, or other serial controller.
RS-232 Control / Protocol 3000 Baud Rate: 115,200 Parity: None Data Bits: 8 Command Format: ASCII Stop Bits: 1 Example: (adjust analog audio output 1 to “-10dB”): #x-aud-lvl out.analog_audio.1.audio.1,-10 Default Ethernet Parameters (Set to DHCP ON) Fallback IP Address: 192.168.1.39 UDP Port #: 50000 Subnet mask: 255.255.0.0 TCP Port #: 5000 Gateway: 192.168.0.1 User/Password Admin/Admin Factory Reset Recessed Button Press and hold while powering the device. Protocol 3000: “#factory” command. Web Pages: In the Settings page, click Reset.