PARMIDA ‎PLED-T818W6KV2-AB-F-20P 20-Pack 4FT LED T8 Hybrid Type A+B Light Tube Instruction Manual

PARMIDA ‎PLED-T818W6KV2-AB-F-20P 20-Pack 4FT LED T8 Hybrid Type A+B Light Tube Instruction Manual & troubleshooting

PARMIDA ‎PLED-T818W6KV2-AB-F-20P 20-Pack 4FT LED T8 Hybrid Type A+B Light Tube Instruction Manual  & troubleshooting 1

PARMIDA ‎PLED-T818W6KV2-AB-F-20P 20-Pack 4FT LED T8 Hybrid Type A+B Light Tube

PARMIDA ‎PLED-T818W6KV2-AB-F-20P 20-Pack 4FT LED T8 Hybrid Type A+B Light Tube Instruction Manual  & troubleshooting 2INSTALLATION INSTRUCTION

WARNING 

  • Risk of fire or electric shock. When installing with an electronic ballast, please check the compatible ballast list first. If you do not find your ballast on the list, please bypass the fixture. Do not install the LED Tube with a ballast that is not listed on our compatible ballast list – risk of fire.
  • Risk of fire or electric shock. LED Retrofit Kit installation requires knowledge of luminaire electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
  • Risk of fire or electric shock. Install this kit only in the luminaires that have the construction features and dimensions shown in the photographs and/or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.
  • Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
  • To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
  • Installers should not disconnect existing wires from lampholder terminals to make new connections at lamp holder terminals. Instead installers should cut existing lampholder leads away from the lampholder and make new electrical connections to lampholder lead wires by employing applicable connectors.
  • For a linear tubular LED lamp conversion, there shall be text or a diagram showing how the supply connections were made to the lampholders so the correct connections will be made to the lamp when the lamp is installed or replaced.
  • This retrofit kit is accepted as a component of a luminaire where the suitability of the combination shall be determined by authori- ties having jurisdiction.
  • If the tube is installed as Type B, the luminaire, once modified as retrofit fixture will no longer operate fluorescent lamps.
  • These lamps should be installed by a licensed electrician.
  • These lamps are to be used indoors (damp or dry locations only). Not suitable for wet location.
  • Under Type A setting this device can be used with compatible emergency ballasts and compatible dimming ballasts (please refer to compatible ballast list).
  • Under Type B setting this device is not suitable for use with emergency ballasts or dimming ballasts.

“PLUG & PLAY” INSTALLATION (TYPE A) 

* Before installation, please check our compatible ballast list and ensure your ballast is listed. If it is not listed, please install your LED tubes according to the Type B Installation Method instructions below.

  • Disconnect power to the light fixture at the breaker panel before installation.
  • Remove the diffuser from the light fixture (if applicable).
  • Remove the existing fluorescent tubes from the light fixture.
  • Install the LED tubes.
  • Install diffuser (if removed in step 2).
  • Switch on power to the light fixture.

“PLUG & PLAY” WIRING DIAGRAM PARMIDA ‎PLED-T818W6KV2-AB-F-20P 20-Pack 4FT LED T8 Hybrid Type A+B Light Tube Instruction Manual  & troubleshooting 3

RETROFIT INSTALLATION (TYPE B) 

NOTE

Can be installed with either single or double ended connection.Double -ended connection can be used with either shunted or non-shunted sockets (tombstones). For single-ended connections,please use non-shunted sockets.
Please install your LED tubes according to the Type B Installation Method instructions below.

  1. Disconnect power to the light fixture at the breaker panel before installation.
  2. Remove the diffuser lens from the light fixture (if applicable).
  3. Remove any existing fluorescent tubes by rotating them a one quarter turn and sliding them out.
  4. Remove ballast cover (cover may be secured with screws or tabs).
  5. Retrofit light fixture according to the diagram applicable to your fixture.

SINGLE-ENDED CONNECTION PARMIDA ‎PLED-T818W6KV2-AB-F-20P 20-Pack 4FT LED T8 Hybrid Type A+B Light Tube Instruction Manual  & troubleshooting 4

DOUBLE-ENDED CONNECTION PARMIDA ‎PLED-T818W6KV2-AB-F-20P 20-Pack 4FT LED T8 Hybrid Type A+B Light Tube Instruction Manual  & troubleshooting 5

Retrofit luminaire with inductive ballast

  1. Disconnect the wires between starter and ballast according to the figure.
  2. Connect two wires to branch circuit Land N according to the figure.

SINGLE-ENDED CONNECTION PARMIDA ‎PLED-T818W6KV2-AB-F-20P 20-Pack 4FT LED T8 Hybrid Type A+B Light Tube Instruction Manual  & troubleshooting 6PARMIDA ‎PLED-T818W6KV2-AB-F-20P 20-Pack 4FT LED T8 Hybrid Type A+B Light Tube Instruction Manual  & troubleshooting 7

DOUBLE-ENDED CONNECTION PARMIDA ‎PLED-T818W6KV2-AB-F-20P 20-Pack 4FT LED T8 Hybrid Type A+B Light Tube Instruction Manual  & troubleshooting 8Retrofit luminaire with electronical ballast

  1. Disconnect the wires between tombstone and ballast according to the figure.
  2. Connect two wires to branch circuit Land N according to the figure.

SINGLE- ENDED CONNECTION PARMIDA ‎PLED-T818W6KV2-AB-F-20P 20-Pack 4FT LED T8 Hybrid Type A+B Light Tube Instruction Manual  & troubleshooting 9PARMIDA ‎PLED-T818W6KV2-AB-F-20P 20-Pack 4FT LED T8 Hybrid Type A+B Light Tube Instruction Manual  & troubleshooting 10

DOUBLE-ENDED CONNECTIONPARMIDA ‎PLED-T818W6KV2-AB-F-20P 20-Pack 4FT LED T8 Hybrid Type A+B Light Tube Instruction Manual  & troubleshooting 11

Retrofit luminaire with two lamps and one electronical ballast

  1. Disconnect the wires between tombstone and ballast according to the figure.
  2. Connect two wires to branch circuit Land N according to the figure.

SINGLE-ENDED CONNECTION 

PARMIDA ‎PLED-T818W6KV2-AB-F-20P 20-Pack 4FT LED T8 Hybrid Type A+B Light Tube Instruction Manual  & troubleshooting 12PARMIDA ‎PLED-T818W6KV2-AB-F-20P 20-Pack 4FT LED T8 Hybrid Type A+B Light Tube Instruction Manual  & troubleshooting 13

DOUBLE- ENDED CONNECTION 

PARMIDA ‎PLED-T818W6KV2-AB-F-20P 20-Pack 4FT LED T8 Hybrid Type A+B Light Tube Instruction Manual  & troubleshooting 14

Retrofit luminaire with three lamps and one electronic ballast

  1. Disconnect the wires between tombstone and ballast according to the figure.
  2. Connect two wires to branch circuit Land N according to the figure.

SINGLE-ENDED CONNECTION PARMIDA ‎PLED-T818W6KV2-AB-F-20P 20-Pack 4FT LED T8 Hybrid Type A+B Light Tube Instruction Manual  & troubleshooting 15PARMIDA ‎PLED-T818W6KV2-AB-F-20P 20-Pack 4FT LED T8 Hybrid Type A+B Light Tube Instruction Manual  & troubleshooting 16

DOUBLE-ENDED CONNECTIONPARMIDA ‎PLED-T818W6KV2-AB-F-20P 20-Pack 4FT LED T8 Hybrid Type A+B Light Tube Instruction Manual  & troubleshooting 17

Retrofit luminaire with four lamps and one electronic ballast

  1. Disconnect the wires between tombstone and ballast according to the figure.
  2. Connect two wires to branch circuit Land N according to the figure.PARMIDA ‎PLED-T818W6KV2-AB-F-20P 20-Pack 4FT LED T8 Hybrid Type A+B Light Tube Instruction Manual  & troubleshooting 18

SINGLE-ENDED CONNECTION PARMIDA ‎PLED-T818W6KV2-AB-F-20P 20-Pack 4FT LED T8 Hybrid Type A+B Light Tube Instruction Manual  & troubleshooting 19

DOUBLE-ENDED CONNECTION PARMIDA ‎PLED-T818W6KV2-AB-F-20P 20-Pack 4FT LED T8 Hybrid Type A+B Light Tube Instruction Manual  & troubleshooting 20

Insert LED tubes

  1. Read the label on the LED tube to ensure the power end of the LED is aligned with the powered tube
    socket, then insert the LED tube by sliding pins into sockets and rotating a quarter turn until the LED tube locks in place.
  2. LED lamps are now fully installed.

Replace the diffuser lens of the light fixture (if applicable).
After modification completed. Attach the Replacement Marking and Cautionary Label to a visible place on theluminaire and keep it visible after installation.
Restore power to the circuit/luminaire and test the light. If necessary, adjust position of the LED tube{s).

BALLAST COMPATIBILITY LIST. 4FT TS TYPE A+B TUBE 

  1. These tubes are compatible with the ballasts listed below. If you intend to install this tube with any ballast not listed below, risk of damage or losses may occur. We are not liable for any damage or losses incurred by not following the instructions in this document.
  2. If you do not see the exact model number of your ballast on this list, it means we have not tested the ballast and cannot guarantee that it will work with our TB tubes. If this is the case for you, we recommend directly wiring your tubes for the best results.
Brand Model No.
ACT ACT3P32ISUNVE
ACT ATC4P32ISUNVE
DAMAR 1688B
DAMAR 1688D
DAMAR 3654C
EIKO PM-2X32T8-UNV-IS
ESPEN VE232MVHIPLE
ESPEN VE2P32MVHIPE 11068
ESPEN VE2P32MVHIPHE 11069
ESPEN VE332MVHIPLE
ESPEN VE3P32MVHIPE 11070
ESPEN VE3P32MVHIPLE 11056
ESPEN VE4P32MVHIPE 11072
ESPEN VE4P32MVHIPLE 11057
ESPEN VEL-4P32-SC
ESPEN VEL100BN-4C
ESPEN VEL30BN-2C-10V
ESPEN VEL30BN-2C-10V(White)
ESPEN VEL50BN-2C
ESPEN REZ-2S32-SC
ESPEN REZ-3S32-SC
ESPEN VE2P32MVHPPE 11080
ESPEN VE4P32MVHPPE 11086
FULHAM FH12-UNV-1400L-CEC
GE GE132MAX-G-N
GE GE132MAX-H/Ultra
GE GE-132-MV-N
GE GE232-120RES-B
GE GE232MAX-G-N
GE GE232MAX-G-N-DIYB
GE GE232MAXG-N-DIYL
GE GE232MAX-L/UL TRA
Brand Model No.
GE GE-232-MV-N
GE GE332MAX-G-H
GE GE332MAX-G-N
GE GE332MAX-G-N-DIYB
GE GE332MAXP-N/ULTRA
GE GE432MAX-G-N
GE GE432MAXG-N-DIYL
GE GE432MAX-L/Ultra
GE GE432MAX-N/Ultra
GE GE432MAXP-L/ULTRA
GE GE132-MVPS-H
GE GE-132-MV-PS-L
GE GE232-MV-PS-H
GE GE232-MVPS-L
GE GE232-MVPS-N
GE GE-232-MV-PS-N
GE GE-232-MVPS-XL
GE GE240RES 120-4PK
GE GE240RES 120-B
GE GE332-MVPS-L
GE GE-332-MVPS-XL
HALCO EP2/32IS/MV/MC/HE
HALCO EP232IS/MV /HE
HALCO EP332IS/L/MV/HE
HALCO EP332IS/MV/HE
HALCO EP4/32IS/MV/MC/HE
HALCO EP432IS/L/MV /HE
HALCO EPL2/32IS/MV/MC/HE
HALCO EPL3/32IS/MV /SC/HE
HALCO EPL4/32IS/MV/MC/HE
KEYSTONE KT-EMRG-1400
KEYSTONE KT-EMRG-500-SL
Brand Model No.
KEYSTONE KTEB-232RIS-1-TP-SL/J
KEYSTONE KTEB-232-UV-IS-N-P
KEYSTONE KTEB-332-UV-IS-N-P
KEYSTONE KTEB-432RIS-1-TP-SL
KEYSTONE KTEB-432-UV-IS-N-P
OSRAM SYLVANIA OHE 1X32T8/UNV ISL-SC
OSRAM SYLVANIA OHE 1X32T8/UNV ISN-SC
OSRAM SYLVANIA OHE 2X32T8/UNV ISL-SC-1
OSRAM SYLVANIA OHE 3X32T8/UNV HT-SC
OSRAM SYLVANIA OHE 3XLEDT8/UNV-ISN-SC
OSRAM SYLVANIA OHE 4X32T8/UNV ISN-SC
OSRAM SYLVANIA OHE 4XLEDT8/UNV-ISN-SC
OSRAM SYLVANIA OTP 2X59T8/UNV ISN-SC
OSRAM SYLVANIA OTP 3X32T8/UNV ISN-SC
OSRAM SYLVANIA OTP 4X32T8/UNV ISN-SC
OSRAM SYLVANIA OHE 3X32T8/UNV-PSN-SC
OSRAM SYLVANIA OHE 4X32T8/UNV PSX-SC
OSRAM SYLVANIA OHE 2X32T8/UNV PSN-MC
OSRAM SYLVANIA OHE 2X32T8/UNV PSX-MC
OSRAM SYLVANIA OTP 2X32T8/UNV ISN-SC
PHILIPS ADVANCE ICN-1P32-N
PHILIPS ADVANCE ICN-2P32-N
PHILIPS ADVANCE ICN-3P32-N
PHILIPS ADVANCE ICN-4P32-N
PHILIPS ADVANCE IOP-2P32-HL-N
PHILIPS ADVANCE IOP-2P32-LW-N
PHILIPS ADVANCE IOP-2P32-N
PHILIPS ADVANCE IOP-2P59-N
PHILIPS ADVANCE IOPA-1P32-LW-N
PHILIPS ADVANCE IOPA-2P32-LW-N
PHILIPS ADVANCE IOPA-2P32-N
PHILIPS ADVANCE IOPA-3P32-LW-N
Brand Model No.
PHILIPS ADVANCE IOPA-3P32-LW-SC
PHILIPS ADVANCE IOPA-3P32-N
PHILIPS ADVANCE IOPA-4P32-LW-N
PHILIPS ADVANCE IOPA-4P32-N
PHILIPS ADVANCE REB-4P32-SC
PHILIPS ADVANCE ICN-2S40-N
PHILIPS ADVANCE IOP-2PSP32-N
PHILIPS ADVANCE IOP-4PSP32-SC
PHILIPS ADVANCE RELB-2S40-N
PLUSRITE BAF232IS/MV
PLUSRITE BAF332IS/MV
PLUSRITE BAF432IS/MV
PLUSRITE BAF232PS/MV
ROBERTSON IEA432T8120N 3P20135
SUNLITE 40155-SU·SB/232/MV
ULTRASAVE UT 232347
UNIVERSAL B232IUNV-C
UNIVERSAL B232IUNVEL-N
UNIVERSAL B232IUNVHEH-A
UNIVERSAL B232IUNVHP-N
UNIVERSAL B332IUNVEL-A
UNIVERSAL B332IUNVHE-A
UNIVERSAL B332IUNVHP-A
UNIVERSAL B432IUNVHE-A
UNIVERSAL B432IUNVHP-A
UNIVERSAL B232PUNVHE-B
UNIVERSAL B432PUNVHE-A
ESPEN VEL30BN-2C-10V
ESPEN VEL30BN-2C-10V(White)
KEYSTONE KT-EMRG-1400
KEYSTONE KT-EMRG-500-S L
FULHAM FH12-UNV-1400L-CEC

WARNING: Please note that Parmida LLC is not responsible for any problems occurring from an installation with any ballast model number not found on our compatible ballast list. Any subsequent issues resulting from the installation with a non-listed ballast will not be covered under our warranty.

FAQ


Setting up PARMIDA ‎PLED-T818W6KV2-AB-F-20P 20-Pack 4FT LED T8 Hybrid Type A+B Light Tube Instruction Manual is easy with these step-by-step instructions. Follow the steps are you are set-up in no time.

Using PARMIDA ‎PLED-T818W6KV2-AB-F-20P 20-Pack 4FT LED T8 Hybrid Type A+B Light Tube Instruction Manual is simple by using this manual. Follow the instructions one by one and everything will be fine

Is PARMIDA ‎PLED-T818W6KV2-AB-F-20P 20-Pack 4FT LED T8 Hybrid Type A+B Light Tube Instruction Manual stuck or not working properly? By resetting it you can set it back to the standard settings and everything should be back to normal. This works in many cases when problems arise.

This page contains the complete user instructions & manual for PARMIDA ‎PLED-T818W6KV2-AB-F-20P 20-Pack 4FT LED T8 Hybrid Type A+B Light Tube Instruction Manual

All symbols, colors and codes for PARMIDA ‎PLED-T818W6KV2-AB-F-20P 20-Pack 4FT LED T8 Hybrid Type A+B Light Tube Instruction Manual are explained in this instruction manual. You can find everything you need and moree