PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual & troubleshooting

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 1
EasyKey
7300
Lever Smart Door Lock
User manual

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 2

Bluetooth Edition Please use the following URI to register your product and get support from us: www.phiLips.com/support

Important info

Security
  • Before using Philips EasyKey, please read and understand all instructions. Damage caused by non-compliance with the instructions will not be covered by the warranty.
  • Use only the manufacturer-specified accessories/components.
  • Use only the alkaline batteries the product is equipped with, or use the same specification type of alkaline batteries.
  • Do not forcibly disassemble this product to avoid triggering an alarm or damaging the product.
  • Do not scrape the fingerprint sensor with sharp objects, otherwise, it may cause permanent damage.
  • Do not expose products to environments where there is water leakage or splashing.
  • Do not expose the product to corrosive substances to prevent damaging the protective cover.
  • Do not hang objects on the handle, in case it might affect the normal use of the lock.
  • Please clean the product with a soft cloth.
  • Do not remove the battery during setting up and operating.
  • Please let a professional technician to install the door lock and follow the installation guidelines provided. Do not disassemble the lock by yourself. Keep relevant sealed stickers properly. Do not easily disclose the password information
  • Please modify the default master PIN code immediately after installation and configuration, and keep the mechanical key properly.
  • Please replace all the batteries immediately if there is a low battery alarm. Please make sure to correctly match the poles (+/-) when installing the batteries.
Caution
  • Do not place the battery near a fire to avoid an explosion.
  • Do not use any emergency power supply that does not meet the safety requirements to power up the product.
  • Do not connect the 2 poles of the batteries with metals to avoid a short circuit which may lead to an explosion.
  • Please make sure any component replacement is executed by Philips, Philips authorized service center or professional technicians.
  • Do not use accessories or parts that have been produced by other manufacturers or have not been specifically recommended by Philips. Use of such accessories and parts may void your warranty.
Disposal of used products and batteries
  • You can have your locks reclaimed at Philips authorized service centers. You will receive corresponding compensation if your products meet our conditions.
  • Please learn by yourself the local electronic product classification and collection system.
  • Please abide by local regulations and do not mix used products with ordinary domestic waste.
  • Proper disposal of used products can help to avoid potential negative impacts on the environment and human health.
  • This product contains batteries that can not be disposed of together with domestic waste.
  • Please learn the local regulations concerning battery classification and collection by yourself. Proper disposal of used batteries can help to avoid negative impacts on the environment and human health.

Install your EasyKey

Packaging list

This packaging list is for reference only. Please refer to the actual packaging contents.PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 3

Exploded Views

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 4

1. Inner escutcheon
bottom part (x1)
2. Battery cover(x1)
3. M6 fixed screw (x2)
4. Inner escutcheon(x1)
5. Square shaft
compressed spring (x2)
6. Square shaft (x2)
7. Mortise(x1)
8. Fixed screw (x4)
9. M6 connecting
screw tube (x2)
10. Outer escutcheon(x1)
11.M6 fixed screw (x1)
12.M5 fixed screw (x3)
13. Mounting plate (x1)
14. M5 connecting
screw tube (x3)
Pre-installation instructions

Step 1 | Check the door opening direction
This product can be installed on doors of 4 types of opening directions: left-out pull, right-in push, right-out pull, and left-in push.PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 5

Step 2 | Change the handle direction

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 6

  1. Remove the 2 crosses recessed screws, 1 cross recessed set and 1 lever protective cover in the escutcheon.
  2. Rotate the lever to 180 degrees
  3. Put the 2 screws back and tighten them.

Step 3 | Change the latch bolt direction
You can change the direction of the latch bolt to adapt to doors of different opening directions. When the bolt bevel faces out the door, it is for outwards door opening; And when the bolt bevel faces in the door, it is for inwards door opening.PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 7

  1. Push the inverting tailpiece to the top.
  2. Press the latch bolt down to the mortise surface, then rotate it 180 degrees and pull it out.
  3. Push the tailpiece to the bottom.
  4. Change the direction of the directional screw according to your actual needs (the directional screw must be installed on the inside of the door, i.e. the inside escutcheon)

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 8 Attention

  1. Choose a proper installation kit based on the door thickness;
  2. The default tool kit is applicable to door thicknesses of 38-60mm. If your door thickness is out of this range, please contact us.
Installation steps

The following installation steps apply to right-open doors. For left-open doors, please read the [Pre-installation instructions] carefully and make needed adjustments.

  1. Use the drilling template to drill the needed holes on the door and mount the mortise into the door.
  2. Tighten up the 4 fixed screws when inserting the mortise.PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 9
  3. Install the connecting screw tube, and place the square shaft and compressed spring into the hole of the lever. (The square shaft compressed spring must be put towards the lever)PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 10PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 11 Attention
    Please cut the key tailpiece according to your needs and use a square shaft and connecting screw tube with the proper length to fix the screw tube.
  4. Pass the connection wire through the hole on the mortise. Align the cylinder key tailpiece and the square shaft with the 2 rotary holes on the mortise, and insert them to make sure the outside escutcheon is kept close to the outside of the door.PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 12
  5. Tighten up the mounting plate with 3 anchor screws against the inside of the door.PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 13
  6. Put the compressed spring, then the square shaft into the inside escutcheon. Insert the outside escutcheon connection wire and mortise wire into the corresponding sockets on the inside escutcheon. Align the square shaft to the rotary holes on the mortise and insert them to make the inside escutcheon close to the inside of the door.PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 14PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 15 Attention
    Please make sure the extra connection wire is hidden in the door hole.
  7. Tighten the 2 anchor screws.PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 16
  8. Install the batteries, then the battery cover, and the inside lower cover.PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 17
  9. Try the inside and outside levers,, the mechanical key, and check if all components are well connected.PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 18

Get to know your EasyKey

Outside escutcheon

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 19

1 Keypad
2 Card reader
3 Mute button
4 Low battery indicator
5 Outside forced lock button
6 Fingerprint sensor
7 Lever
8 Door status indicator
9 Emergency power interface
10 Reset button
11 Mechanical keyhole
Inside escutcheon

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 20

1 Battery cover
2 Lever
3 Safe handle switch
4 A/M mode switch
5 Reset button
6 Close button

How to set up your EasyKey

Pre-setup Instructions:
  • There are 2 operating modes in EasyKey: General mode and dual verification mode.
General mode Dual verification mode
Unlock with any registered
identity information
Unlock with any two of PIN
code, card and fingerprint
  • User Number
    You can delete single user information by its user number without having to delete everything in the system.
  • You can record the user information in the following table for future query.
Number Name Fingerprint PIN Code Card
0
1
2
3
4
5
6
7
8
9
  • Icon annotation

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 21

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 22 Attention

  1. Press [*] key to return to the previous menu.
  2. The default master PIN code is 12345678.
  • How to enter master mode:PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 23
  1. Press [#] key before inputting any other numbers. After hearing a voice prompt of “Enter master PIN code”, enter your master PIN code and confirm with [#]. Then you are in master mode.

Modify master PIN code

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 24Press [#], enter master PIN code and confirm with [#].

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 25
Press [1] to modify master PIN code.

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 26

Enter the new master PIN code and confirm with [#]. Re-enter the new master PIN code and confirm with [#]. After hearing a voice prompt of “Succeeded”, press [*] several times until you exit master mode.

User settings

Register a user PIN code

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 27Press [#], enter master PIN code and confirm with [#].

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 28
Press [2] to enter user registration, then press [1] to register a new user PIN code, which will be automatically numbered and broadcasted by the system. PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 29

Enter a user PIN code of 6 to 12 digits,and confirm with [#]. Then reenter the user PIN code and confirm with [#]. After hearing a voice prompt of“Succeeded”, press [*] several times until you exit master mode.
Register a one-time user PIN codePHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 30
Press [#], enter master PIN code and confirm with [#].

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 31Press [2] to enter user settings, then press [2] again to enter one-time PIN code registration.

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 32

Enter a one-time user PIN code of 6 to 12 digits and confirm with [#]. Re-enter the user PIN code and confirm with [#]. After hearing a voice prompt of “Succeeded”, press [*] several times until you exit master mode.

Register a fingerprint
Press [#], enter master PIN code and confirm with [#].

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 33

Press [2] to enter user settings, then press [3] to enter fingerprint registration. The system will automatically number the fingerprint and broadcast the number.

Place your finger against the sensor. After hearing a voice prompt of “Take away your finger and enroll again”, please take away your finger and re-place it against the sensor. After hearing a voice prompt of “Succeeded”, press [*] several times until you exit master mode.
Register a card

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 34Press [#], enter master PIN code and confirm with [#].PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 35

Press [2] to add a new user, then press [4] to enter card registration. The system will automatically number the card and broadcast the number.PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 36

Hold the card close to the card reader until you hear a beep. After hearing a voice prompt of “Succeeded”, press [*] several times until you exit master mode.

User Information Deletion

Delete a user PIN codePHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 37
Press [#], enter master PIN code and confirm with [#].PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 38

Press [3] to enter user deletion, then press [1] tenter user PIN code deletion. Press [1] again to delete a single user PIN code.PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 39

Enter the 2-digit [user number] (00-09) of the user PIN code that is to be deleted and press [#] to confirm. After hearing a voice prompt of “Succeeded”, press [*] several times until you exit master mode.
Delete all user PIN codesPHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 40

Press [#], enter master PIN code and confirm with [#].

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 41

Press [3] to enter user deletion, then press [1] to enter user PIN code deletion. Press [2] to delete all user PIN codes. After hearing a voice prompt of “Succeeded”, press [*] several times until you exit master mode.
Delete a one-time user PIN codePHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 42

Press [#], enter master PIN code and confirm with [#].PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 43

Press [3] to enter user deletion, then press [2] to enter one-time user PIN code deletion.PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 44

After hearing a voice prompt of “Succeeded”, press [*] several times until you exit master mode.
Delete a fingerprintPHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 45

Press [#], enter the master PIN code and confirm with [#].PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 46

Press [3] to enter user deletion, then press [3] again to enter fingerprint deletion. Press [1] to enter single fingerprint deletion.PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 47

Enter the 2-digit [user number] (00-99) of the fingerprint that is to be deleted and confirm with [#]. After hearing a voice prompt of “Succeeded”, press [*] several times until you exit master mode.

Delete all fingerprints

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 48Press [#], enter master PIN code and confirm with [#].
PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 49
Press [3] to enter user deletion, then press [3] again to enter fingerprint deletion. Press [2] to delete all fingerprints. After hearing a voice prompt of “Succeeded”, press [*] several times until you exit master mode.
Delete a cardPHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 50
Press [#], enter the master PIN code and confirm with [#].PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 51

Press [3] to enter user deletion, then press [4] to enter card deletion. Press [1] to delete a single card and then press [*] several times until you exit master mode.

Delete all cardsPHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 52

Press [#], enter master PIN code and confirm with [#].
PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 53
Press [3] to enter user deletion, then press [4] to enter card deletion. Press [2] to delete all cards. After hearing a voice prompt of “Succeeded”, press [*] several times until you exit master mode.
System date initializationPHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 54

Remove the inside lower cover and double click the [RES] button with a sharp object, until you hear a voice prompt of “Restored to factory settings”. All user information will be emptied.
Language SettingsPHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 55

Press [#], enter the master PIN code and confirm with [#].PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 56
Press [4] to enter system settings, then press [1] to enter language settings.PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 57

Adjust the language to needed: For Chinese, press [1]; for English, press [2]. After hearing a voice prompt of “Succeeded”, press  [*] several times until you exit master mode.
PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 58 Attention
The default language is English.

Volume settings

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 59Press [#], enter the master PIN code and confirm with [#].
Press [4] to enter system settings, then press [2] to enter volume settings.

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 60Adjust the volume as needed: For higher volume, press [1]; for lower volume, press [2]; for mute mode, press [3]. After hearing a voice prompt of “Succeeded”, press [*] several times until you exit master mode.
PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 61 Attention
The default volume is “higher volume”.

System settings

Switch to dual verification modePHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 62

Press [#], enter master PIN code and confirm with [#].PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 63

Press [4] to enter system settings, then press [3] to choose the verification method.

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 64

For single verification, press [1]; for dual verification, press [2]. After hearing a voice prompt of “Succeeded”, press [*] several times until you exit master mode.

Extended Functions

Press [#], enter master PIN code and confirm with [#].PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 65

Press [5] to enter extended functions. PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 66
To join a network, press [1]. To exit a network, press [2]. Before setting up the extended functions, please download and open the Philips EasyKey APP via your mobile phone.PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 67
PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 68 Attention
The extended functions are optional.

System Query

Anti-fake code queryPHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 69
Press [#], enter the master PIN code and confirm with [#].
PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 70
Press [6] to enter system query, then press [1] to get the serial number (anti fake code) automatically broadcasted.
PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 71Attention
Enter 400# is a shortcut to start system query.

Local Query

Press [#], enter master PIN code and confirm with [#].
PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 72
Press [6] to enter system query, then press [2] to get the software version automatically broadcasted.PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 73
PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 74 Attention
Enter 114# is a shortcut to start local query.

Bluetooth Settings

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 75

Press [#] and input master Pin code, then press [#] to confirm.PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 76
Press [7] to enter Bluetooth settings.PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 77
To disable Bluetooth, press [3]. After hearing a voice prompt of “Settings succeeded”, press [*] back to the previous menu until you exit master mode.
PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 78 Attention

  1. Bluetooth switch shortcut, directly input 403# to open the Bluetooth module, input 404# to turn off the Bluetooth module.
  2. When the Bluetooth is off, please press [1] to enable Bluetooth.

How to use your EasyKey

Unlock | Unlock from outside

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 79

  1. Touch the keypad to wake up the system.
  2. Enter the registered user PIN code and confirm with [#].
  3. After hearing a voice prompt of “Door opened”, press down the handle to open the door.

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 80

  1. Place your registered finger properly on the sensor.
  2. After hearing a voice prompt of “Door opened”, press down the handle to open the door.

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 81

  1. Place your registered card on the card reader.
  2. After hearing a voice prompt of “Door opened”, press the handle to open the door.
Unlock | Unlock from inside

With handle

Philips EasyKey employs an indoor fast opening mortise allowing you to directly press down the handle to unlock.
PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 82 Attention
When you want to open the door from inside, please make sure the safe handle switch is toggled to green scale and the safe handle function is disabled.PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 83

Lock | Lock from outside/inside

Lock from outsidePHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 84

The sensor bolt can detect the signal when you close the door, and the motor will drive the main deadbolt to let it automatically pop up and lock the door.

Lock from inside
The sensor bolt can detect the signal when you close the door, and the motor will drive the main deadbolt to let it automatically pop up and lock the door.PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 85

Deadlock from inside

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 86

After the door is locked, long-press the [CLOSE] button until the button flashes in red and there is a voice prompt of “Inside deadlock enabled”.
PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 87 Attention
Under inside deadlock mode, all functions of the outside escutcheon will be locked. If you try to wake up the system manually, the keypad area will display the combination of “15937(X)” and there will be a voice prompt of “Inside deadlock enabled”
reminding you that the door has been deadlocked from inside.
Under deadlock mode, all operations on the outside escutcheon are disabled. Master PIN code verification or mechanical key opening is required to unlock the door from deadlock mode.

Auto and manual modes

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 88

[A] represents Auto mode. The deadbolt will pop up automatically after closing the door and the door will be locked.
[M] represents Manual mode. The deadbolt will not pop up automatically after closing the door and the door will stay open.

Lock from outside the door

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 89 Under Auto Mode, shutting the door will make the deadbolt automatically pop up and there will be a voice prompt of “Door closed”.
PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 90 Under Manual Mode, the deadbolt won’t pop up automatically after shutting the door. Only fingerprint, card or PIN code verification can make it automatically pop up. After the door is locked, you will hear a voice prompt of “Door closed”. You can wake up the outside escutcheon to unlock and open the door after the door is closed.

Lock from inside the door

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 91 Under Auto Mode, shutting the door will make the deadbolt automatically pop up and there will be a voice prompt of “Door closed”.
PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 92PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 93 Under Manual Mode, the deadbolt won’t pop up automatically after shutting the door. Only after you double-click the [CLOSE] button within a second can the deadbolt pop up and lock the door. After the door is locked, you will hear a voice prompt of “Door closed”.
Mechanical key opening

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 94

  1. Cut the box with scissors and take out the key shell. Push the cover aside and reveal the key itself.
  2. Insert the key into the keyhole and keep the key and key shell vertical to each other. Rotate the key shell towards the handle for 90° until it becomes close to the door surface.
  3. Rotate the key shell downwards for 180°to to make the key shell parallel to the ground. Then rotate the key shell horizontally towards the handle to unlock the door.

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 95 Attention
It is suggested that not to use the mechanical key for daily unlocking. Use the key for emergencies, i.e. when the battery has been running out of, when you forget the PIN code, or when the system fails to work properly.

Other functions

Safe handle function: Lock up the handle from inside

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 96

Function:
When the safe handle function is enabled you could lock up the handle from inside and doors can’t be unlocked from inside
How to use:

  1. Enable safe handle function: Toggle the switch to red scale.
  2. Disable safe handle function: Toggle the switch to green scale.

Restore factory settings: one button to return to the initial state

Function:
Empty all user information and restore to factory settings.
How to use:
Double click the [RES] button with a sharp object, and all the user information will be emptied. The lock will be restored to factory settings.PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 97

One-button mute function

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 98

Function:
Use only one button to mute the lock by turning off the voice guide. Applicable to the scenes where you don’t want to disturb your family.
How to use:

  1. Mute: When the system is awake, long-press the [Mute] button for 2 seconds to enter one-time mute mode. The button will glow green.
  2. Unmute: When the system is awake, long-press the [Mute] button for 2 seconds to restore the voice guide. The button will glow white.

Outside forced lock function

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 99

Function:
Unlocking from inside will trigger an alarm. How to use:
After the door is successfully locked, long press the function button for 2 seconds to enter the outside forced lock mode.
PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 100 Attention
Enabling the outside forced lock function will not affect normal unlocking from outside.

Meaning and use of indicators

Lock status indicator

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 101

Colors of the light and the corresponding meanings:
Blue: After the system wakes up, the light will glow blue, indicating that you can operate the lock.
Green: After the door is unlocked, the light will glow green, indicating that the door has been opened.
Red: After the door is locked, the light will glow red, indicating that the door has been closed.

Low battery indicator

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 102

Colors of the light and the corresponding meanings:
After waking up, the system will run an automatic examination on the battery voltage. If the voltage is too low, the light will flash in red and there will be a voice prompt of “Low battery. Please replace all batteries” when the door is open.

Outside forced lock indicator

Colors of the light and the corresponding meanings:
White:

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 103

  1. When the door is locked, the light will light up alone, indicating that you can enable the outside forced lock function.
  2. If you have enabled the outside forced lock function, the light will light up after the system wakes up, indicating this function is in use.
Mute mode indicator

Colors of the light and the corresponding meanings:

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 104

  1. White: Indicates the mute mode is off.
  2. Green: Indicates the mute mode is on.
System lock indicator

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 105If there are 5 consecutive incorrect inputs of any of the 3 types of verification methods (fingerprint/PIN code/card), the system will be locked for 3 minutes.
PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 106 Attention
Only when touching the keyboard panel will the system appears the prompt of the system is locked.

[CLOSE] button indicator

Colors of the light and the corresponding meanings:PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 107

  1. Red light with 2 flashes: Indicates the door has been locked.
  2. Greenlight with 2 flashes: Indicates the door has been unlocked.
  3. Red light with 1 flash: Indicates the door has been deadlocked.

Troubleshooting

Types of alarms and alarm modes
Low battery alarm, reminding you to replace the batteries in time

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 108
Triggering: After waking up, the system will run an automatic examination on the battery voltage. If the voltage is too low, the lock give an alarm and a voice prompt of “Low battery.
Please replace all batteries”.
Alarm mode:A voice prompt of “Low battery.
Please replace all batteries” during unlocking. Turning off: The alarm will be automatically turned off.
Anti-dismantle alarm

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 109

Triggering 1: The door is pried open and the sensor bolt pops up.
Alarm mode: Continuously repeated alarms.
Turning off: The alarm can be turned off automatically or by any one of the successful verification methods.
Triggering 2: Outside escutcheon is pried open and does not tightly fit with the door.
Alarm mode: Continuously repeated alarms. Turning off: Auto-close, or close after one of the successful verification methods, or
close after the normal indoor unlocking.
Abnormal latch bolt alarm

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 110
Triggering: The latch bolt performs abnormally and cannot unlock or lock properly.
Alarm mode: Continuously repeated alarms
Turning off: Automatically turned off.
Outside forced unlock mode: inside unlocking alarm

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 111
Triggering:If the lock is under outside forced lock mode, unlocking from inside will trigger an alarm.
Alarm mode: Continuously repeated alarms
Turning off: The alarm can be turned off by  a successful verification method of any type

How to use an emergency power

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 112

When the battery voltage is insufficient, and the door cannot be opened from the outside, you can power up the lock through the Micro USB interface by using a 5V power bank as an emergency power supply. After opening the door lock, please replace the batteries immediately.
In case of a system crash and it’s unable to open the door from outside, please press the Reset button and then release to let it restart automatically.

How to replace batteries

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 113The lock is powered by 4pcs AA alkaline batteries. There are two sets of working power stations inside the battery case.
Eight batteries can be put in to extend the battery life and reduce battery replacement frequency. The battery case is located at the upper end of the inside escutcheon. By pushing the button at the top of the inside escutcheon, you could take out the battery
cover and the batteries inside.

PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual  & troubleshooting 114

Philips and the Philips Shield Emblem have registered trademarks of Koninklijke Philips N.V. and are used under license. This product has been manufactured by and is sold under the responsibility of Shenzhen Conex Intelligent Technology Co., Ltd., and Shenzhen Conex Intelligent Technology Co., Ltd. is the warrantor in relation to this product.
Version:2.0

FAQ


Setting up PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual is easy with these step-by-step instructions. Follow the steps are you are set-up in no time.

Using PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual is simple by using this manual. Follow the instructions one by one and everything will be fine

Is PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual stuck or not working properly? By resetting it you can set it back to the standard settings and everything should be back to normal. This works in many cases when problems arise.

This page contains the complete user instructions & manual for PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual

All symbols, colors and codes for PHILIPS EasyKey 7300 Lever Smart Door Lock User Manual are explained in this instruction manual. You can find everything you need and moree