SDC GL160 Electrochemical Gate Lock Installation Guide

SDC GL160 Electrochemical Gate Lock Installation Guide & troubleshooting

SDC GL160 Electrochemical Gate Lock Installation Guide
SDC GL160 Electrochemical Gate Lock Installation Guide  & troubleshooting 1

Available Models

GL 160AI: Fail-Safe
GL 260AH: Fail-Secure
GL 163AI: Fail-Safe, Built in Key Switch
GL 263AH: Fail-Secure, Built in Key Switch
GL 260MRA: Fail-Secure, Mechanical Release

Lock Operation

The Lock has an adjustable automatic relock switch (ARS standard) that keeps the bolt retracted until the gate is in a closed position. A Bolt Position Switch (BPS, optional) monitors the lock and unlock position of the bolt. A gate position switch (DPS, optional) is also available to monitor whether a gate is opened or closed.

Specifications

Dimensions: W 5″ x H 6-1/8″ x D 2″
Material: Steel
Finish: Black
Solenoid: Continuous Duty
Bolt Throw: 5/8″
Bolt Dia:: 5/8″
Dual Voltage: 900mA @ 12 VDC, 450mA @ 24 VDC

CAUSTION: DO NO INSTALL LOCKING TONGUE ONTO LOCK UNTIL WIRING IS COMPLETE

GL160A & GL260A – GATE LOCK MOUNTING

Use the lock housing as a template to mark the mounting holes onto the post. If the wiring will go through the post remove cover and mark the wiring hole before mounting. Use a 3/8″ drill size to drill out all holes. Be sure to shim between the mounting brackets as required if the gate post is less than 3″. See illustration 1 & 2.
Determine the hand of gate and install the switches accordingly. See Illustration 3. The Illustration below gives an example of a LH swing and or a RH sliding gate install. To reverse the handing swap the position of the ARS and centering assembly to the opposite side of lock.
Before mounting the locking tongue verify that it is properly aligned within the gate lock opening. The locking tongue should be centered with the bolt and make contact with centering assembly and ARS. Once verified mark the mounting holes and drill use 3/8″ drill size for all holes. See illustration 4.
Refer to page 4 of instructions for wiring information.
Test operation to verify that its functioning properly and re install cover..

  • Illustration 1
    SDC GL160 Electrochemical Gate Lock Installation Guide  & troubleshooting 2
  • Illustration 2
    SDC GL160 Electrochemical Gate Lock Installation Guide  & troubleshooting 3
  • Illustration 3
    SDC GL160 Electrochemical Gate Lock Installation Guide  & troubleshooting 4
  • Illustration 4
    SDC GL160 Electrochemical Gate Lock Installation Guide  & troubleshooting 5
  • Right Hand Sliding Gate Or LH Swing Gate shown
    SDC GL160 Electrochemical Gate Lock Installation Guide  & troubleshooting 6

GL163A & GL263A – BUILT IN KEY SWITCH

Install key cylinder per notes below

  • a) Cylinder must be 1-1/8” mortise type with standard tailpiece. See illustrations 5
  • b) Remove key and invert the tailpiece. See illustration 6.

Refer to page 4 of instructions for wiring information.

  • Illustration 5
    SDC GL160 Electrochemical Gate Lock Installation Guide  & troubleshooting 7
  • Illustration 6
    SDC GL160 Electrochemical Gate Lock Installation Guide  & troubleshooting 8

Note position of mortise cylinder & tailpiece relative to switch. Tailpiece must point up & depress switch button at all times with key removed.

GL260MRA – MECHANICAL RELEASE

Install key cylinder per notes below

  • a) Cylinder must be 1-1/8” mortise type with standard tailpiece. See illustrations 7
  • b) Tailpiece must contact retraction arm as shown in View A-A; See illustration 8.

Refer to page 4 of instructions for wiring.

  • Illustration 7
    SDC GL160 Electrochemical Gate Lock Installation Guide  & troubleshooting 9
  • Illustration 8
    SDC GL160 Electrochemical Gate Lock Installation Guide  & troubleshooting 10

WIRING REFERENCE

  • GL160A Typical wiring
    SDC GL160 Electrochemical Gate Lock Installation Guide  & troubleshooting 11
  1. Auto Relock switch wiring shown with tongue engaged inside lock
  • GL260A/260MRA Typical wiring
    SDC GL160 Electrochemical Gate Lock Installation Guide  & troubleshooting 12
  • GL163A Typical wiring
    SDC GL160 Electrochemical Gate Lock Installation Guide  & troubleshooting 13
  1. Auto Relock switch wiring shown with tongue engaged inside lock
  2. Key switch wiring shown with tailpiece depressing switch
  • GL263A Typical wiring
    SDC GL160 Electrochemical Gate Lock Installation Guide  & troubleshooting 14

OPTIONALMONITORING WIRING REFERENCE

  • Illustration 8
    SDC GL160 Electrochemical Gate Lock Installation Guide  & troubleshooting 15
  • 260 BPS Wiring
    SDC GL160 Electrochemical Gate Lock Installation Guide  & troubleshooting 16
    Shown when Bolt is retracted
  • 160 BPS Wiring
    SDC GL160 Electrochemical Gate Lock Installation Guide  & troubleshooting 17
    Shown when Bolt is retracted
  • DPS Wiring

WHT = COM
YEL = N/C
ORG = N/O
Shown when tongue is inserted

FAQ


Setting up SDC GL160 Electrochemical Gate Lock Installation Guide is easy with these step-by-step instructions. Follow the steps are you are set-up in no time.

Using SDC GL160 Electrochemical Gate Lock Installation Guide is simple by using this manual. Follow the instructions one by one and everything will be fine

Is SDC GL160 Electrochemical Gate Lock Installation Guide stuck or not working properly? By resetting it you can set it back to the standard settings and everything should be back to normal. This works in many cases when problems arise.

This page contains the complete user instructions & manual for SDC GL160 Electrochemical Gate Lock Installation Guide

All symbols, colors and codes for SDC GL160 Electrochemical Gate Lock Installation Guide are explained in this instruction manual. You can find everything you need and moree