V-TAC LED Solar Streetlight Installation Guide

V-TAC LED Solar Streetlight Installation Guide & troubleshooting

V-TAC LED Solar Streetlight Installation Guide  & troubleshooting 2

WEEE Number: 80133970
INSTALLATION INSTRUCTION
LED SOLAR STREETLIGHT

V-TAC LED Solar Streetlight Installation Guide  & troubleshooting 3V-TAC LED Solar Streetlight Installation Guide  & troubleshooting 4

TECHNICAL DATA:

Model VT-ST42
Watts 40W
Lumens 4800LM
LED Chip SMD2835*90PCS
Solar Panel 21W/ 13.5V, Mono-crystalline silicone
material
Li-ion Battery Pack 32700/9.6V/ 12000mAh, replaceable
IP Rating IP65
Beam Angle 140 x 70°-TPIII
Detection Angle 120°
Detection Distance 8- 12 Meters
Product Dimension 706.1 x 289.7 x 73.6mm
Installation Height 3 – 6 Meters
Package 35,000 Hours

INTRODUCTION & WARRANTY

Thank you for selecting and buying V-TAC product. V-TAC will serve you the best. Please read these instructions carefully before starting the installation and keep this manual handy for future reference. If you have any other queries, please contact our dealer or local vendor from whom you have purchased the product. They are trained and ready to serve you at your best. The warranty is valid for 3 years from the date of purchase. The warranty does not apply to damage caused by incorrect installation or abnormal wear and tear. The company gives no warranty against damage to any surface due to incorrect removal and installation of the product. This product is warranted for manufacturing defects only.

WARNING
1. Please make sure to turn off the power before starting the installation.
2. The light source of this luminaire is not replaceable, when the light source reaches its end of life the whole luminaire should be replaced.
3. Installation must be performed by a certified person.
V-TAC LED Solar Streetlight Installation Guide  & troubleshooting 5 This marking indicates that this product should not be disposed of with other household wastes.

V-TAC LED Solar Streetlight Installation Guide  & troubleshooting 6
https://vtacexports.com/pub/media/ftp-upload/manuals/VT-ST42.html

MULTI-LANGUAGE MANUAL QR CODE
Please scan the QR code to access the manual in multiple languages.

FEATURES:

V-TAC LED Solar Streetlight Installation Guide  & troubleshooting 7

WORKING MODES:

V-TAC LED Solar Streetlight Installation Guide  & troubleshooting 8

BUTTON CONTROL:
Please press the button on the lamp to select working modes.
Press 1st time for Mode A.
Press 2nd time for Mode B.
Press 3rd time for off.
REMOTE CONTROL:
Please press the button on the lamp first in order to activate the lamp and then use the remote control to adjust the working modes.

MODE A: CONSTANT LIGHTING MODE

V-TAC LED Solar Streetlight Installation Guide  & troubleshooting 9

Press the button on the lamp 1st time orV-TAC LED Solar Streetlight Installation Guide  & troubleshooting 10 on the remote control, the lamp will automatically turn on at night and keep 60% brightness constantly for 4 hours(induction is invalid), then it turns to Sensor Mode.

MODE B: SENSOR MODE

V-TAC LED Solar Streetlight Installation Guide  & troubleshooting 11

Press button on the lamp 2nd time orV-TAC LED Solar Streetlight Installation Guide  & troubleshooting 12 on the remote control, the lamp will automatically turn on with 100% full brightness when motion is detected in the range ≤ 12mtrs, then turns to 30% brightness in 20 seconds of no motion.

REMIND

1. Above working modes are factory default settings, user can re-set it to: press button on the lamp 1st time for mode B and press 2nd time for mode A, meanwhile also can select different working time or brightness by remote control, after which it will automatically become the latest default working mode.
2. Mode A and Mode B cannot be set to the Constant Lighting Mode at the same time, nor can they be set to the Sensor Mode at the same time.
3. The lamp has memory function. After lamp restarted, it will continue to work in the latest default working mode.

DIY WORKING TIME AND BRIGHTNESS BY REMOTE CONTROL

Remote Control Distance: 12 Meters

Mode A (Constant Lighting Mode): time and brightness are both adjustable.V-TAC LED Solar Streetlight Installation Guide  & troubleshooting 13
FOR EXAMPLE:
① Press button “Constant Lighting Mode”;
② Press button “Time 2H”.
③ Press button “Brightness 60%”.
The lamp will flash one time after press each button above, which indicates it’s set successfully as below: Lamp automatically turns on at night and keep 60% brightness for 2hrs, then it turns to Sensor Mode.

Mode B (Senor Mode): only brightness(when activated by induction) is adjustable.
FOR EXAMPLE:
① Press button “Sensor Mode”;
② Press button “Brightness 60%”.
The lamp will flash one time after press each button above, which indicates it’s set successfully as below: Lamp automatically turns on with 60% brightness when motion is detected in the range ≤ 12mtrs, then turns to weak brightness (30% of 60% brightness) in 20 seconds of no motion.

NOTICE
1. The lamp button is a power-off switch, lamp can get solar charged in any mode.
2. This is a solar-powered lamp, please install it in a location where can get enough sunshine.
3. Please note the lighting time depends on the sunshine duration & weather.
4. Built-in intelligent IC is with over-charge, over-discharge and over-voltage protection.
5. The lamp gets solar-charged at daytime, and lights up automatically at dusk.
6. The lamp is equipped with an internal battery pack, which is replaceable. If any need, please contact seller for correct new battery pack.
7. Non-professionals please do not disassemble the lamp.
8. Please do not dispose the battery with household garbage to avoid explosion.

PACKAGE CONTENT

V-TAC LED Solar Streetlight Installation Guide  & troubleshooting 14

INSTALLATION A: STRAIGHT POLE

(Default installation method, accessories included)

V-TAC LED Solar Streetlight Installation Guide  & troubleshooting 15

① Before starting the installation, ensure the 4 bottom screws are tightened.
② Remove the gaskets of small U-shaped brackets, then insert them to lamp bracket across the straight pole.
③ Tighten the screws to fix lamp onto the pole (Suitable for poles with Φ50-60mm).
④ To adjust the angle of the lamp, loosen the screws from both sides of lamp (as shown in the above image) and adjust the lamp angle, adjustable by upwards 20° and downwards 10°. Then tighten the screws of the lamp.

INSTALLATION B: CURVED POLE

(Default installation method, accessories included)

V-TAC LED Solar Streetlight Installation Guide  & troubleshooting 16

① Loosen the screws and remove the big U-shaped bracket.
② Loosen the bottom screws to match the pole.
③ Install the lamp on the pole (Suitable for poles with Φ50mm).
④ Adjust the lamp and balance it, tighten the four screws to lock the lamp.

INSTALLATION C: WALL MOUNTED (OPTIONAL)

(Requirements for wall mounted installation: 2 pcs expansion screws M10*60mm (NOT Included in the packaging))

V-TAC LED Solar Streetlight Installation Guide  & troubleshooting 17

① Before starting the installation, ensure the 4 bottom screws are tightened.
② Drill 2 holes of φ14mm with a depth of 60mm and holes distance 104mm on the wall.
③ Use 2 expansion screws to fix the lamp on the wall.
④ To adjust the angle of the lamp, loosen the screws from both sides of lamp (as shown in the above image) and adjust the lamp angle, adjustable by upwards 20° and downwards 10°. Then tighten the screws of the lamp.

In case of any query/issue with the product, please reach out to us at: [email protected] For More products range, inquiry please contact our distributor or nearest dealers. V-TAC EUROPE LTD. Bulgaria, Plovdiv 4000, bul.L.Karavelow 9B

References

FAQ


Setting up V-TAC LED Solar Streetlight Installation Guide is easy with these step-by-step instructions. Follow the steps are you are set-up in no time.

Using V-TAC LED Solar Streetlight Installation Guide is simple by using this manual. Follow the instructions one by one and everything will be fine

Is V-TAC LED Solar Streetlight Installation Guide stuck or not working properly? By resetting it you can set it back to the standard settings and everything should be back to normal. This works in many cases when problems arise.

This page contains the complete user instructions & manual for V-TAC LED Solar Streetlight Installation Guide

All symbols, colors and codes for V-TAC LED Solar Streetlight Installation Guide are explained in this instruction manual. You can find everything you need and moree