velleman VIS1 CCTV Indoor Scanner User Manual

velleman VIS1 CCTV Indoor Scanner User Manual & troubleshooting

velleman VIS1 CCTV Indoor Scanner User Manual
velleman VIS1 CCTV Indoor Scanner User Manual  & troubleshooting 1

Thank you for buying a Velleman product! Please read the manual thoroughly before bringing this device into service. If the device was damaged in transit, don’t install or use it and contact your dealer.

Introduction

To all residents of the European Union

Important environmental information about this product

velleman VIS1 CCTV Indoor Scanner User Manual  & troubleshooting 2 This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm the environment.

Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialized company for recycling.

This device should be returned to your distributor or to a local recycling service.

Respect the local environmental rules.

If in doubt, contact your local waste disposal authorities.

As safety, security and usage requirements vary according to the country or area of buy, please contact your local authorities for an installation and use complying with local requirements.

Installation

General

The table lists the correct cable connections.

Mounting the Scanner

This scanner is designed to operate indoors only and can support a max. load of 15.41lbs (=7kg). In order to perform adequately, the device should be securely fastened to a suitable mounting surface. The camera should be correctly mounted and balanced on the scanner. The round-based scanner is installed directly on the mounting bracket.

Tighten the scanner’s mounting screws just enough so that the base is effectively immobilised.

CAUTION

Do not attach the unit to a drywall. Attach the scanner to the mounting bracket using a hex head screw equipped with a locknut or use our camera mounting bracket (CAMB7 or CAMB8).

  Normal Mounting Inverted Mounting
Number Connection Color Connection Color
         
1 24VAC RED 24VAC RED
2 LEFT WHITE RIGHT GREEN or YELLOW
3 RIGHT GREEN or YELLOW LEFT WHITE
4 COMMON BLACK COMMON BLACK

Note that the “LEFT” and “RIGHT” connections are inverted with inverted mounting of the device.

Inverted Mounting of the Unit

The left-right directions for manual operation are reversed with inverted mounting of the device. Correct the wiring accordingly when connecting the control unit with the scanner: the cores connected to pin 2 and pin 3 at the back of the central unit should be switched. Consult figures “2c” and “2d” at the back of the manual for inverted mounting of the scanner and the camera.

Connecting the Scanner to the Central Unit

The power cable of the scanner can be connected to the connections at the back of the central unit (the scanner uses a 24VAC power supply) for independent and automatic operation. Connect the cores of the cable as shown in the table (see above).

Installing the Limit Stops

The toothed wheel is slotted at intervals of 5°. The coiled (extension) cord with BNC connector is connected to the rear of the scanner. The reversing switch activator (1 in fig. 1 at the back of the manual) is visible between the toothed wheel and the housing on the front side of the unit.

Located on the toothed wheel are two adjustable plastic limit stops (2 and 3 in fig. 1). Both limit stops can be removed, enabling the scanner to rotate 360°.

Perform steps 1 through 5 outlined in “Manual Operation of the Scanner” (see below) to establish approximate limit stop settings before mounting the camera. At least 1 of the limit stops should be installed or the scanner will continue its turning motion. Make sure that the camera covers the required detection area and that the rear of the scanner faces away from the area to be covered.

Manual Operation of the Scanner
  1. Connect the central unit to a standard 220V-outlet, activate the device and put the “MANUAL/AUTO”-switch in the “MANUAL”-position.
  2. Hold the ‘LEFT/RIGHT” toggle switch in the “RIGHT”-position until the scanner has reached the desired right hand position.
  3. Install the first limit stop (2 in fig. 1) just to the right of the switch actuator (1 in fig. 1) by snapping it in place.
  4. Put the “MANUAL/AUTO”-switch in the “MANUAL”-position and hold the “LEFT/RIGHT”-toggle switch in the “LEFT”-position.
  5. Install the second limit stop (3 in fig. 1) to the left of the switch actuator (see step 3).
  6. Mount the camera on the scanner. Read “Mounting the Camera” (see below).
  7. Have the camera pan to both limits (left and right) to verify the position of the limit stops.
Mounting the Camera

Do not use an auto-iris lens with this unit. This would cause the iris mechanism to wear very quickly, as an auto-iris lens constantly compensates for the varying light level.

Use a screw with a locknut to mount the camera. Place this screw in one of three positions (see 5 in fig. 1) in order to obtain the best possible balance.

The scanner has an off-center pivot which allows the camera to tilt from 10 degrees below horizon level to 90 degrees above or vice versa, depending on how the camera is mounted (see figures at the back of the manual).

Loosen the hex-head screws (4 in fig. 1) with locknut on the side of the mounting bracket to adjust the angle of the camera. Retighten the two screws firmly when the desired angle has been obtained.

For more info concerning this product, please visit our website www.velleman.eu.

The information in this manual is subject to change without prior notice.

FIGURES

SCANNER
velleman VIS1 CCTV Indoor Scanner User Manual  & troubleshooting 3

  1. switch actuator
  2. right limit stop
  3. left limit stop
  4. hex-head screw (2)
  5. Camera mounting hole (3)

MOUNTING

velleman VIS1 CCTV Indoor Scanner User Manual  & troubleshooting 4velleman VIS1 CCTV Indoor Scanner User Manual  & troubleshooting 5
velleman VIS1 CCTV Indoor Scanner User Manual  & troubleshooting 6
velleman VIS1 CCTV Indoor Scanner User Manual  & troubleshooting 7

velleman VIS1 CCTV Indoor Scanner User Manual  & troubleshooting 8

 

References

FAQ


Setting up velleman VIS1 CCTV Indoor Scanner User Manual is easy with these step-by-step instructions. Follow the steps are you are set-up in no time.

Using velleman VIS1 CCTV Indoor Scanner User Manual is simple by using this manual. Follow the instructions one by one and everything will be fine

Is velleman VIS1 CCTV Indoor Scanner User Manual stuck or not working properly? By resetting it you can set it back to the standard settings and everything should be back to normal. This works in many cases when problems arise.

This page contains the complete user instructions & manual for velleman VIS1 CCTV Indoor Scanner User Manual

All symbols, colors and codes for velleman VIS1 CCTV Indoor Scanner User Manual are explained in this instruction manual. You can find everything you need and moree