VIVO Black 43″ x 24″ Instruction Manual
Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product.
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual and do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly, or inappropriate use.
ELECTRICAL SAFETY INSTRUCTIONS
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.
- DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
- DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
- NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR SELLER TO REPLACE DAMAGED PARTS.
- NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE MADE CONTACT WITH LIQUIDS.
- ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
- OUTDOOR USE IS PROHIBITED.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED
Assemble the desktops (L, M, N) using the desktop connectors (Q) and flat head screws (P). Tighten screws with a Phillips screwdriver.
Loosen the two set screws on the telescopic crossbar (A) using the Allen wrench (S-F) and partially extend the crossbar.
Place the crossbar spacer (D) on the motorized leg (B) as shown. Attach the telescopic crossbar to the legs (B, C) as shown using M6x12mm bolts (S-A), and tighten with the Allen wrench (S-F). NOTE: Insert all necessary screws into holes before tightening
Attach the side brackets (E) to both ends of the frame using four M6x12mm bolts (S-A). Tighten with the Allen wrench (S-F).
Loosen the knob on the socket end of the sync rod (F) and slide the sync rod onto the shaft of the motorized leg. Tighten the knob.
Loosen the knob on the other end of the sync rod and extend the hex shaft into the socket in the leg, making sure the shaft is fully inserted with the red O-ring bumper spaced no more than 0.5” from the leg. Tighten the knob.
Place the frame upside down on the desktop, extend to match the desktop mounting holes, then tighten the set screws with the Allen wrench (S-F).
Place the feet (G) on the legs as shown. Insert and tighten bolts (S-A) using the Allen wrench (S-F).
Place the adapter holder (H) over the telescopic crossbar and tighten the two thumbscrews. Place the AC adapter (I) into the adapter holder (H).
Connect the AC adapter and motorized leg to the controller (K). Connect the power cable (J) to the AC adapter.
Insert the anti-vibration pads (S-E) into the desktop mounting holes in the crossbar and side brackets.
Place the assembled frame on the desktop, making sure the holes are aligned with the desk frame, and secure the frame using ST4.2×20 screws (S-B).
Attach the controller to the underside of the desktop using ST3.5×20 screws (S-C) as shown. Once the controller is installed, cable clips (S-D) can be attached to the desk for cable management.
If necessary, adjust foot pads to level the desk. Plug the power cable (J) into an AC wall outlet.
Press and hold the UP or DOWN buttons to operate the desk.
|No response while pressing button||Check to make sure all cables are fully connected.|
|The desktop cannot be lifted||Make sure the desktop and other items do not exceed the weight limit (121lbs).|
|Duty cycle exceeded (max. 2min operating)||Allow desk to rest for 18 minutes.|
Failure to follow these instructions may result in property damage and/or personal injury.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
www.vivo-us.com AVG. RESOLUTION TIME (within office hrs): < 15 M Chat live with an agent! 309-278-5303 AVG. RESOLUTION TIME (within office hrs): 5M 4S
LAST UPDATED: 02/02/2021 REV2