VonHaus 3515389 9AMP Electric Tacker Instruction Manual

VonHaus 3515389 9AMP Electric Tacker Instruction Manual & troubleshooting

VonHaus 3515389 9AMP Electric Tacker Instruction Manual  & troubleshooting 1 VonHaus 3515389 9AMP Electric Tacker

VonHaus 3515389 9AMP Electric Tacker Instruction Manual  & troubleshooting 2

GENERAL SAFETY INFORMATION.

WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Please retain all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tools or battery-operated
(cordless) power tools.

INTENDED USE.
This 2 in 1 Nail & Staple Gun is intended for domestic use only and should not
be used for commercial or industrial purposes.
This tool is not intended for use by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instructions concerning the use of the tools by a person responsible for their safety. Children should be supervised to ensure they do not play with the tool.

WORK AREA SAFETY.
Keep your work area clean and well lit. Cluttered or dark areas invite accidents. Do not operate power tools in explosive atmospheres such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
Keep bystanders, children and animals away whilst operating a power tool. Distractions can cause you to lose control. ELECTRICAL SAFETY.
Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
Do not expose power tools to rain or wet conditions. Water entering the power tools will increase the risk of electric shock.

BEFORE USE.

Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use power tools whilst you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce the risk of personal injury.
Always wear eye protection. Any power tool can throw foreign objects into your eyes and cause permanent eye damage. Always wear safety goggles (not glasses) that comply with ANSI safety standard Z87.1. Every day glasses have only impact resistant lenses. They are not safety glasses.

WARNING!

Wearing glasses or goggles not in compliance with ANSI Z87.1 when operating this tool could cause serious injury.
Prevent unintentional starting. Ensure the switch is in the off position before connecting to the power source and/
or battery pack, picking up or carrying the tools. Carrying power tools with your finger on the switch, or energising power tools that are switched on, invites accidents.
Dress appropriately. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts to prevent them from becoming caught in the tool.

IMPORTANT SAFETY INFORMATION FOR USE

WARNING!

  • Know your 9A Electric Tacker. Do not plug the tool into the power source until you have read and understand the information in this manual.
  • Learn the tool’s applications and limitations, as well as the specific potential hazards related to the tool, to reduce the risk of electric shock, fire or serious injury.
  • Use the power tool, accessories and tools bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. Only use accessories designed for use with the tool.
  • Secure the workpiece. Use clamps or a vice to hold the workpiece as this is safer than using your hand and frees both hands to operate the tool.
  • Do not use the power tool if the switch does not turn it on and off. A power tool that cannot be controlled with the switch is dangerous and must be repaired.
  • Do not force the power tool. Always
    use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
  • Do not overreach. Keep proper footing and balance at all times. This will enable better control of the power tool in unexpected situations.
  • Disconnect the plug from the power source and/or the battery and remove the nails/staples from the power tool before making any adjustments, changing accessories or storing. Such preventative safety measures reduce the risk of starting the power tool accidentally.
  • Store idle power tools out of reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the tool.
  • Power tools are dangerous in the hands of untrained users.
  • Maintain the power tool. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.

IMPORTANT PRODUCT CARE INFORMATION.
Ensure you have read all of the safety information in the previous pages before using the tools.

If the power tool is immersed in water or any other liquid, is subject to a severe drop or does not operate within the guidelines of this Instruction manual, discontinue use immediately and have it checked.

SPECIFICATIONVonHaus 3515389 9AMP Electric Tacker Instruction Manual  & troubleshooting 3

  1. Tacker Head
  2. Handle
  3. Trigger
  4. Magazine Release Clip
  5. Magazine
  6. Tacking Strength Adjustment Dial
  7. On/Off Switch
  8. Staple Magazine
  9. Nail Magazine
  10. Tacking Head Cover (see page 9)
  11. Safety Retaining Plate (see page 9)
  12.  Fire Retaining Plate (see page 9)
  13. Fire Retaining Pin (see page 9)

 

STAPLE SPECIFICATION

STAPLE

Fires 18 Gauge, 5.7mm (1/4”) Narrow Crown staples (equivalent to type 90, No.90 Narrow Crown (5.7mm, 1/4”) of the following lengths:

  • 15mm (9/16”)
  • 16mm (5/8”)
  • 18mm (11/16”)
  • 19mm (3/4”)

NAIL

Fires 18 Gauge Brad nails, 2mm (1/16”) Crown (Equivalent to Tacwise 18G, Arrow BN18, Bostitch 18G & Rapid no. 8 brad nails) of the
following lengths:

  • 15mm (9/16”)
  • 16mm (5/8”)
  • 21mm (13/16”
  • 25mm (1”)
  • 30mm (1-3/16””)
  • 32mm (1-1/4”)

VonHaus 3515389 9AMP Electric Tacker Instruction Manual  & troubleshooting 4

INSERTING STAPLE MAGAZINE

Always unplug the 9A Electric Tacker from the mains supply before performing any cleaning & maintenance tasks

WARNING! Ensure the 9A Electric Tacker is disconnected from the mains supply before attempting to insert/remove staples.

Hold the appliance upside down. Push down the MAGAZINE RELEASE CLIP (4) on the end of the MAGAZINE (5) and slide back fully to its end point. Place the STAPLE MAGAZINE (8) into the track of the Magazine channel. Close the MAGAZINE (5) until it clicks back into place.

VonHaus 3515389 9AMP Electric Tacker Instruction Manual  & troubleshooting 5

INSERTING NAIL MAGAZINE

Always unplug the 9A Electric Tacker from the mains supply before performing any cleaning & maintenance tasks

WARNING! Ensure the 9A Electric Tacker is disconnected from the mains supply before attempting to insert/remove staples.

Hold the appliance upside down. Push down the MAGAZINE RELEASE CLIP (4) on the end of the MAGAZINE (5) and slide back fully to its end point. Place the NAIL MAGAZINE (9) into the track of the Magazine channel.
Close the MAGAZINE (5) until it clicks back into place.

VonHaus 3515389 9AMP Electric Tacker Instruction Manual  & troubleshooting 6

SWITCHING ON/OFF

Stay alert, watch what you are doing, and use common sense when operating a power tool

Plug the 9A Electric Tacker into a suitable mains socket.
Press the ON/OFF SWITCH (7) to the I position to switch on the Tacker.
Press the ON/OFF SWITCH (7) to the 0 position to switch off the Tacker

VonHaus 3515389 9AMP Electric Tacker Instruction Manual  & troubleshooting 7

IMPACT STRENGTH ADJUSTMENT

Always unplug the 9A Electric Tacker from the mains supply before performing any cleaning & maintenance tasks

NOTE: Switch off the 9A Tacker at the mains supply before making adjustments to the Tacking Strength.

Rotate the TACKING STRENGTH ADJUSTMENT DIAL (6) clockwise to increase the strength. Rotate the TACKING STRENGTH ADJUSTMENT DIAL (6) anti – clockwise to decrease the strength

  • – Used for light materials such as foils and fabrics.
  • + Used for robust materials such as woods and walls.

VonHaus 3515389 9AMP Electric Tacker Instruction Manual  & troubleshooting 8NOTE Before starting a job, find the optimal impact level by testing on spare material first.

OPERATION

Stay alert, watch what you are doing, and use common sense when operating a power tool

NOTE: The 9A Electric Tacker will not operate unless both the TACKER HEAD (1) and TRIGGER (3) are simultaneously depressed

Hold the 9A Electric Tacker with a firm grip on the HANDLE (2). Place into the desired position and firmly push down, so the TACKER HEAD (1) is de-pressed

The 9A Electric Tacker is now *active.

The TACKER HEAD (1) now de-pressed, squeeze the TRIGGER (3) to deliver a magazine round. Release the TRIGGER (3) once a staple is delivered and lift the 9A Electric Tacker off the surface to release the TACKER HEAD

VonHaus 3515389 9AMP Electric Tacker Instruction Manual  & troubleshooting 9VonHaus 3515389 9AMP Electric Tacker Instruction Manual  & troubleshooting 10

CLEARING A JAM

Always unplug the 9A Electric Tacker from the mains supply before performing any cleaning & maintenance tasks

WARNING Switch off at the mains supply, and allow at least 20 minutes to allow the Tacker to cool sufficiently before clearing a jam.

  • Pull the rubber TACKING HEAD COVER (10) away from the Tacking head area.
  • Using a 3mm Hex Key (not provided) unscrew both Hex Bolts holding the Tacking Plates in place.
  • Rotate anti-clockwise the loosen and clockwise to tighten.
  • Slide the SAFETY RETAINING PLATE (11) out.
  • Slide the FIRE RETAINING PLATE (12) out.
  • Lift the FIRE RETAINING PIN (13) away to remove the jam.
  • Replace the FIRE RETAINING PLATE (12), SAFETY RETAINING PLATE (11), and secure both with the Hex Bolts back onto the Tacking Head base plate.

VonHaus 3515389 9AMP Electric Tacker Instruction Manual  & troubleshooting 11 IMPORTANT Ensure all Tacking Head plates are replaced correctly and are secured with the Hex Bolts.

TROUBLESHOOTING

VonHaus 3515389 9AMP Electric Tacker Instruction Manual  & troubleshooting 12

CLEANING & MAINTENANCE

Always unplug the 9A Electric Tacker from the mains supply before performing any cleaning & maintenance tas

  • Clean dust and debris from the staple gun vents and magazine compartment using compressed air.
  • Do not use solvents, or household cleaning detergents containing ammonia to clean the 9A Electric Tacker.
  • Use only mild soap and a damp cloth to clean the 9A Electric Tacker.

NOTE Do not lubricate. The 9A Tacker does not require oil or grease to operate

CAUTION Do not alter, attach special fixtures to, or redesign parts of the 9A Tacker. Do not fire without staples, as this may cause damage to the 9A Tacker

CUSTOMER SERVICE

If you are having difficulty using this product and require support, please contact [email protected] For US Customers please contact [email protected]

WARRANTY

To register your product and find out if you qualify for a free extended warranty please go to www.Vonhaus.com/warranty.
Please retain a proof of purchase receipt or statement as proof of the purchase date. The warranty only applies if the product is used solely in the manner indicated in the Warnings page of this manual, and all other instructions have been followed accurately. Any abuse of the product or the manner in which it is used will invalidate the warranty. Returned goods will not be accepted unless re-packaged in its original packaging and accompanied by a relevant and completed returns form. This does not affect your statutory rights.
No rights are given under this warranty to a person acquiring the appliance second-hand or for commercial or communal use. All material in this instruction manual are copyrighted by DOMU Brands. Any unauthorised use may violate worldwide copyright, trademark, and other laws.

FAQ


Setting up VonHaus 3515389 9AMP Electric Tacker Instruction Manual is easy with these step-by-step instructions. Follow the steps are you are set-up in no time.

Using VonHaus 3515389 9AMP Electric Tacker Instruction Manual is simple by using this manual. Follow the instructions one by one and everything will be fine

Is VonHaus 3515389 9AMP Electric Tacker Instruction Manual stuck or not working properly? By resetting it you can set it back to the standard settings and everything should be back to normal. This works in many cases when problems arise.

This page contains the complete user instructions & manual for VonHaus 3515389 9AMP Electric Tacker Instruction Manual

All symbols, colors and codes for VonHaus 3515389 9AMP Electric Tacker Instruction Manual are explained in this instruction manual. You can find everything you need and moree