WinBridge T9 Bluetooth Portable PA Speaker System User Manual

Contents hide

1 WinBridge T9 Bluetooth Portable PA Speaker System

2 Front View

3 Black View

4 Common Function Instructions

5 Top View

6 UHF Wireless Microphone

7 Remote Function

8 Troubleshooting Guidelines

9 Package included

10 Documents / Resources

WinBridge T9 Bluetooth Portable PA Speaker System

Front View

M: Source Selection for UHF Microphone, AUX In, Bluetooth, TF/Micro SD, USB Flash Drive; Under UHF Mode Long Press 3s to Enter Pairing Status with A Voice Prompt: UHF Waiting for Connection;)
In Audio Playing Mode, Press To Pause, Press Again To Play;
Press To Select Previous
Press To Select Next;

Black View

Common Function Instructions

MIC: Support V4″ Microphone Cable Input;
USB Port: Support a USB Flash Drive, Maximum Up To 32G (MP3 WAV WMA);
TF Card Slot: Support TF/Micro SD Cards, Maximum Up To 32G (MP3 WAV WMA);
Audio In: Support 3.5mm Audio Cable Input;
Webcast: Refer To Page 5;
Headset/ Speaker Output: Refer To Page 5;

Top View

UHF Wireless Microphone

Remote Function

How to Connect UHF Microphone to the PA Speaker

Turn on PA speaker with power switch on the black of the control panel: “(uil_)”
Short press M button on the front of control panel to switch to UHF model with screen shows: UHF
Long press M button again for 3 seconds to enter UHF pairing mode with voice prompt: “UHF is waiting for connection
Turn on UHF microphone by pressing power switch;
Press mic power switch button 3 times rapidly;
When the frequency on the mic screen flashing, you should hear the voice prompt: “UHF is connected!” which means pairing was successful;

Friendly Reminder

Please strictly follow the above steps, especially the second and third steps;

How to Do A Live Stream

Pair UHF wireless microphone to speaker; or you could plug wired 1/4″ microphone included to MIC jack;
Connect RED cable end into webcast jack, another end into your phone or computer for live stream; If you sing and would like have accompaniment, then connect BLACK cable end into AUX in jack, another end into your phone or speaker ( optional connect );
Or you could connect bluetooth from phone to get music accompaniment;
Plug headset/earphone/headphone into headset jack, then you could hear what you said and music play;

Friendly Reminder:

Please read the structure diagram above carefully before do a live webcast;
Idea for Youtube, Karaoke, Audio Performance etc, Support A Variety of Mainstream Live Software;

How to Connect Bluetooth?

How to Play USB drive or TF card

Just connect a USB drive or TF card, then speaker will play music automatically. Please make sure your USB or TF card have music files.

HOW TO CHARGING & MAINTAINING SPEAKER

Please note:

Use the included 15V AC power adapter to charge the speaker internal rechargeable battery.
Plug adapter into 110~240 AC outlet. connect the cable end into the DC 15V power input on black control panel of PA speaker system.
It will normally take 6-8 hours to fully charge the battery if it is lower at 0% strength.
Battery status: there are 4 battery strength indicator bars on the LED screen on the front of the PA speaker system unit, each bar represents 25% of the total battery strength.
When charging is required, a voice prompt will indicate, “low battery, please charge.” the battery indicator will blink while charging. It will stop blinking when battery is fully charged.
Recharge the battery within 48 hours of “low battery” voice prompt. In order to extend the life of the internal battery, please charge it regularly even if system is not being used.
It is suggested that you charge the internal battery an additional 1-2 hour safter fully charged to extend its life.
Please DO NOT over charge the battery by leaving the system plugged in continuously. This will reduce the life of the internal rechargeable battery and could cause over heating.

HOW TO CHARGING UHF MICROPHONE