Winco Commercial Rotating Heated & Humidified Holding Display Merchandiser Instruction Manual

Winco Commercial Rotating Heated & Humidified Holding Display Merchandiser Instruction Manual & troubleshooting

Winco Commercial Rotating Heated & Humidified Holding Display Merchandiser Instruction Manual  & troubleshooting 1

COMMERCIAL
ROTATING HEATED & HUMIDIFIED HOLDING DISPLAY MERCHANDISER

Operating Instruction Manual

Winco Commercial Rotating Heated & Humidified Holding Display Merchandiser Instruction Manual  & troubleshooting 2

Winco Commercial Rotating Heated & Humidified Holding Display Merchandiser Instruction Manual  & troubleshooting 3

Model Voltage Power Amperage Plug Type

Overall Dimensions

Product

Weight

Length Depth Height
EDM-1K 110-120V — 60Hz 1500W 13.1A NEMA 5-15P 23-5/8″ (600mm) 25-1/4″ (641mm) 27- /16″ (700mm) 70 lbs 32 kgs

BEFORE OPERATING ANY EQUIPMENT, READ AND FAMILIARIZE YOURSELF WITH THESE USE AND SAFETY INSTRUCTIONS

Congratulations on your purchase of this WINCO® commercial equipment. WINCO takes pride in the quality of its products. When used as intended and with proper care and maintenance, you will experience years of reliable operation from this equipment. To ensure the best results, it is important that you read and follow the instructions in this manual carefully. It’s important to save these instructions for future reference.

COMMERCIAL ROTATING HEATED & HUMIDIFIED HOLDING DISPLAY MERCHANDISER

Important For Future Reference

Please complete this information and retain this manual for the life of the equipment.
For Warranty Service and/or parts, this information is required.

Model Number ————————————————
Serial Number ————————————————-
Date Purchased ———————————————–

Winco Commercial Rotating Heated & Humidified Holding Display Merchandiser Instruction Manual  & troubleshooting 4 WARNING: IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE, OR MAINTENANCE CAN CAUSE PROPERTY DAMAGE, INJURY, OR DEATH. READ THE INSTALLATION, OPERATION, AND MAINTENANCE INSTRUCTIONS THOROUGHLY BEFORE INSTALLING OR SERVICING THIS EQUIPMENT.

Winco Commercial Rotating Heated & Humidified Holding Display Merchandiser Instruction Manual  & troubleshooting 5 CAUTION: THESE MODELS ARE DESIGNED, BUILT, AND SOLD FOR COMMERCIAL USE ONLY. IF THESE MODELS ARE POSITIONED SO THE GENERAL PUBLIC CAN USE THE EQUIPMENT, MAKE SURE THAT CAUTION SIGNS, WARNINGS, AND OPERATING INSTRUCTIONS ARE CLEARLY POSTED NEAR EACH UNIT SO THAT ANYONE USING THE EQUIPMENT WILL USE IT CORRECTLY AND NOT INJURE THEMSELVES OR HARM THE EQUIPMENT.

Winco Commercial Rotating Heated & Humidified Holding Display Merchandiser Instruction Manual  & troubleshooting 6 WARNING: A FACTORY-AUTHORIZED SERVICE PROVIDER SHOULD HANDLE ALL MAINTENANCE AND REPAIR. BEFORE DOING ANY MAINTENANCE OR REPAIR, FOLLOW THE SERVICE SETUP ARRANGEMENT ON PAGE 15.

Introduction

Congratulations on the purchase of your WINCO® equipment. Please take the time to carefully read through this manual to ensure the unit is operated and maintained properly, to ensure the best possible performance from this product for many years.

WINCO will not accept liability if:

  • The instructions in this manual have not been followed correctly.
  • Non-authorized personnel has tampered with the equipment.
  • Non-original spare parts are used.
  • The machine has not been handled and cleaned correctly.
  •  There is no use damage to the unit.

Immediately Inspect for Shipping Damage
All containers should be examined for damage before and during unloading.
The freight carrier has assumed responsibility for its safe transit and delivery.

If equipment is received damaged, either apparent or concealed, a claim must be made with the delivering carrier.

A. Apparent damage or loss must be noted on the freight bill at the time of delivery. It must then be signed by the carrier representative (Driver). If this is not done, the carrier may refuse the claim. The carrier can supply the necessary forms.

B. If concealed damage or loss is not apparent until after the equipment is uncrated, a request for inspection must be made to the carrier within
15 days. The carrier should arrange an inspection. Be certain to keep all contents and packaging material.

Package Contents

In the box:
  • (1) EDM-1K Commercial Rotating Heated & Humidified Holding Display Merchandiser
  • (1) 4-Tier, 18″ Diameter Round Rack
  • (1) Operating Instruction Manual

WINCO prides itself on quality and service, ensuring that at the time of packing, all products are supplied fully functional and free of damage. Should you find any damage as a result of freight, please contact your WINCO dealer immediately.

Unpacking the Equipment

DISPOSE OF ALL PACKAGING MATERIALS IN AN ENVIRONMENTALLY RESPONSIBLE MANNER.

  1. Remove all packing materials and tape, as well as any protective plastic and cardboard, from the unit.
  2. Clean any glue residue leftover from the plastic or tape.
  3. Place the unit in the desired position and height.

SAVE THE ORIGINAL BOX AND PACKAGING FOR USE IN PACKAGING AND SHIPPING THE EQUIPMENT IF SERVICES ARE NEEDED.

Function and Purpose

This unit is intended for use in commercial food-service operations only. It is not intended for household, industrial or laboratory use.

Please keep this manual in a safe place for future use!

NOTE
Please remember that this manual and the warning labels do not replace the need to be alert, properly train and supervise operators, and use common sense when using this equipment.

Important Safeguards

To ensure safe installation and operation, please carefully read and understand the following statements.

Unless the operator is adequately trained and supervised there is a possibility of serious injury. Owners of this equipment bear the responsibility to make certain that this equipment is used properly and safely and to strictly follow all of the instructions contained in this manual and the requirements of local, state, or federal law.

Owners should not permit anyone to touch this equipment unless they are over 18 years old, are adequately trained and supervised, and have read and understood this manual.

Owners should also ensure that no customers, visitors, or other unauthorized personnel come in contact with this equipment. It is the responsibility of the owner and the operator to remain alert to any hazards posed by the function of this equipment.

If there is ever uncertainty about a particular task or the proper method of operating this equipment, ask an experienced supervisor or contact Winco® for assistance.

Warnings
This manual contains a number of precautions to follow to help promote the safe use of this equipment.

Winco Commercial Rotating Heated & Humidified Holding Display Merchandiser Instruction Manual  & troubleshooting 7 WARNING

Winco Commercial Rotating Heated & Humidified Holding Display Merchandiser Instruction Manual  & troubleshooting 8 USE CAUTION WHEN TOUCHING THE UNIT.

FOR YOUR SAFETY
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

WARNING
Improper installation, adjustment, alteration, service, or maintenance can cause property damage, injury, or death.
Read this installation, operating, and maintenance instructions thoroughly before installing or servicing this equipment.

TO PURCHASER
Contact your local gas supplier and ask for instructions in the event the user smells gas. This information should be posted in a prominent location.

Important Safeguards

These instructions should be followed at all times. Failure to follow these instructions could result in injury to yourself and others.

TO REDUCE RISK OF INJURY OR DAMAGE TO THE UNIT:

  1.  Read this manual thoroughly before installation and operation.
    DO NOT proceed with installation and operation if you have any questions or do not understand anything in this manual. Contact your representative or the manufacturer first.
  2. DO NOT touch any surfaces that may be hot.
  3. Unplug from outlet when not in use prior to installing or removing parts and before cleaning. Allow for the device to cool first before handling.
  4. To protect against the risk of electrical shock, do not immerse the appliance, cord, or plug in water, or other liquids.
    Winco Commercial Rotating Heated & Humidified Holding Display Merchandiser Instruction Manual  & troubleshooting 9

    Winco Commercial Rotating Heated & Humidified Holding Display Merchandiser Instruction Manual  & troubleshooting 10 WARNING 

    Electrical Shock Hazard Keep water and other liquids from entering the inside of the unit. The liquid inside the unit could cause an electrical shock.
    Do not spray water or cleaning products. Liquid could contact the electrical components and cause a short circuit or an electrical shock. Do not use the unit if the power cord is damaged or has been modified.
  5. DO NOT operate this device or any other electrical equipment with a damaged cord or plug, or after the unit malfunctions, is dropped or damaged in any manner. Return to the nearest WINCO Authorized Service Center for examination, repair, and/or adjustment.
  6. The use of accessory attachments not recommended by WINCO may cause fire, electric shock, or injury.
    Winco Commercial Rotating Heated & Humidified Holding Display Merchandiser Instruction Manual  & troubleshooting 11

    Winco Commercial Rotating Heated & Humidified Holding Display Merchandiser Instruction Manual  & troubleshooting 12 WARNING 

    Fire Hazard.
    Correct installation precautions, procedures, and regulations must be followed. Operation and safety training is necessary for all users of this equipment.
  7. Not intended for outdoor installation.
  8. DO NOT let the cord hang over the edge of a table or counter, or touch hot surfaces.
  9. DO NOT place on/near a hot gas / electric burner, or heated oven.
  10. This appliance should always be on a stable and steady countertop or table. Allow sufficient space around the cooking area. Never use the unit on/near low-heat-resistant materials (carpet, vinyl).
  11. This appliance is not intended for use by individuals (including children) with reduced or impaired physical, sensory or mental capabilities, or lack of experience or knowledge unless they have been given proper supervision or instruction concerning the use of this appliance by a person responsible for their safety.
  12.  Any objects that are not intended for use with the appliance should not be in the unit or placed in between the rack wires.
  13. Clean with caution – if a wet sponge or cloth is used to wipe spills on a hot cooking surface, exercise caution to avoid steam burns.
    NOTE: some cleaners may produce noxious flames when applied to a hot surface.
  14. Do not store any item on top of this unit when in operation.
  15. Never place materials such as paper, cardboard, plastic, etc. on or under this unit.
  16. Proper connections and power supply are essential for efficient performance.
  17. If an extension cord power supply is used,
    a. The marked electrical rating of the extension cord should be rated the same or greater than the electrical rating of the unit.
    b. The cord should be located so that it does not drape over the counter/tabletop and can not be damaged or moved unintentionally.
  18. The units are wired to be used with a standard 120V/AC receptacle and may be plugged into any convenient outlet.
  19. The installation of the unit must conform to the NATIONAL ELECTRIC CODE, ALL LOCAL ELECTRIC CODES, AND ORDINANCES, AND
    ALL THE LOCAL ELECTRICAL COMPANY RULES AND REGULATIONS.
    Additionally, we recommend a 4″ spacing surrounding the unit in order to provide adequate ventilation.

Proper Grounding

This machine is provided with a three-pronged grounding plug. The outlet to which this plug is connected must be properly grounded. If the receptacle is not the proper grounding type, contact an electrician. DO NOT, under any circumstances, cut or remove the third ground prong from the power cord or use any adapter plug.

Winco Commercial Rotating Heated & Humidified Holding Display Merchandiser Instruction Manual  & troubleshooting 13

USE A GROUNDED OUTLET DO NOT ADD AN ADAPTOR TO THE PLUG

Operation

Winco Commercial Rotating Heated & Humidified Holding Display Merchandiser Instruction Manual  & troubleshooting 14

  1. Plugin the power cord and turn on the power.
    NOTE: “LO H2O” will flash on the display until water has been added to the water tank.
  2. CHANGE TEMPERATURE DISPLAY FOR EITHER FAHRENHEIT OR CELSIUS:
    • Remove the top cover (Fig. A) > unscrew the Phillips Head screws.
    • Remove the cover on the rear digital display (Fig. B) > unscrew the Phillips Head screws to expose the circuit board (Fig. C).
    • Move dip switch 1 (Fig. D) to either the “ON” position for Celsius or to the “1” position for Fahrenheit.
    • Reinstall rear cover (Fig. B), then top cover (Fig. A).
    Winco Commercial Rotating Heated & Humidified Holding Display Merchandiser Instruction Manual  & troubleshooting 15 Winco Commercial Rotating Heated & Humidified Holding Display Merchandiser Instruction Manual  & troubleshooting 16
  3.  SET AIR TEMPERATURE:
    • Press the air temperature button and the display will show “tSP”.
    It will then show adjustable temperature.
    • Use the UP / DOWN arrow keys to select the desired air temperature from 86°F to 194°F (30°C to 90°C).
    • Wait 15 seconds and the number will be stored, then the display will return to the current temperature.
  4. SET HUMIDITY:
    • Fill water reservoir tank with 1 gal (4 Qts) of DISTILLED WATER or PURIFIED WATER ONLY.
    NOTE: Product failure due to limescale or sediment buildup is not covered under warranty.
    • Refill water as needed for desired humidity. A full tank should last 3-6 hours depending on use.
    • Press the humidity button two times for the display screen to show “hSP”. The display will then show adjustable humidity.
    • Use the UP / DOWN arrow keys to select between 1 (Least humid) and 5 (Most humid).
    • Wait 15 seconds and the number will be stored. The display will return to the current air temperature.
    NOTE: The unit controller will default to the last temperature/ humidity setting upon startup.
  5. Once preheated, open the door. The round rack will stop rotating and can then be manually turned as needed for access.
  6.  Place food products (eg: pizza, pretzels, etc.) on any/all of the four tiers on the round rack.

Removing the Round Rack

Tools needed: Philips Head Screwdriver

  1. Clean any food off the rack.
  2. Using a Phillips Head screwdriver, unscrew the bolt at top of the rack to disengage from the clutch assembly.
  3. Place nut and bolt aside for safekeeping.
  4. Push rack upward slightly to free it from the bottom center alignment guide.
  5. Tilt the round rack toward the door opening and remove it from the unit.

Winco Commercial Rotating Heated & Humidified Holding Display Merchandiser Instruction Manual  & troubleshooting 17

Draining the Unit

  1. Remove all food and debris from the interior of the unit.
  2. Remove the rack from the unit (See Removing Round Rack).
  3. Place a bucket/bowl to catch the water, under the drain located inside the top cabinet.
  4. Turn the drain handle a half turn and allow the unit to empty.
  5. Close drain before adding new water.
  6. The cleaning solution may be run through the water tank. Excess water is needed to flush the cleaning solution through the line and tank until water flows clear (See Cleaning Instructions).

NOTE: Drain the unit before moving it to a new location.

Cleaning, Care & Maintenance

To maintain the appearance and increase the service life, clean the heated merchandiser daily.

Clean all surfaces before using the appliance. Also, clean after each day’s operation; however, the unit may require more frequent cleaning, depending on the volume of production.

  • Switch power off and disconnect from the outlet before cleaning.
  • Unplug the unit when not in operation.
  • Allow merchandiser to cool before attempting to clean.
  • The interior of the heated display merchandiser should be cleaned periodically with warm, soapy water and a soft cloth.
  • The exterior of the unit may be cleaned by carefully wiping with a damp cloth. OK to use glass cleaner on the glass.
  • The rack is removable for easy cleaning.
  • DO NOT immerse the unit in water.
  • DO NOT clean with a pressure washer.
Winco Commercial Rotating Heated & Humidified Holding Display Merchandiser Instruction Manual  & troubleshooting 18

Winco Commercial Rotating Heated & Humidified Holding Display Merchandiser Instruction Manual  & troubleshooting 19 WARNING

Burn Hazard.
When in operation, the appliance surfaces will be HOT!Please take extreme caution.
USE CAUTION WHEN TOUCHING THE UNIT.

WARNING: The interior of the unit will be hot after use.

Exercise caution when handling cooking utensils, cookware/pans.
NOTE: Proper cleaning instructions must be followed, otherwise the operation of the unit may be seriously impaired.
Do not wash parts in an automatic dishwasher.

Removing Lime/Mineral Deposits

NOTE: The amount of sediment content in the water determines how often it will be necessary to delete.

  1. Switch the power to OFF and unplug the power cord. Allow the unit to cool.
  2. After the unit has cooled, drain the unit.
  3.  Fill the water reservoir with a mixture of 70% water and 30% white vinegar only.
  4.  Plugin and turn the unit on.
  5. Set both the air temperature and humidity to their highest settings and allow it to run for 30 minutes.
  6.  Switch the power OFF and unplug the power cord again, allowing cooling.
  7. Drain the unit to empty the deliming solution from the reservoir.
  8. Continue to fill and drain the water reservoir with clean water until the deliming solution is rinsed through and the reservoir is clean.
  9. Replace the rack.
  10. Plug the unit in and fill the reservoir with 1 gal (4 Qts) of DISTILLED WATER or PURIFIED WATER ONLY.

Safety Precautions

Before installing and operating this equipment be sure everyone involved in its operation are fully trained and aware of all precautions. Accidents and problems can result from a failure to follow fundamental rules and precautions.

  • A WINCO® Approved Recommended Qualified Service Technician should carry out repairs if necessary. Do not remove any components or service panels on this product.
  • Before handling, allow the equipment to cool after use.
  • Before cleaning, switch off the power and disconnect the power cord from the outlet.
  • Do not immerse the unit in water or use a hose to clean.
    Ne jamais immerger l’appareil dans l’eau ni utilisez un jet d’eau pour le nettoyer.
  • If the power cord is damaged, it must be replaced by a WINCO® Approved Recommended Qualified Service Technician in order to avoid a hazard.

THIS EQUIPMENT MUST ONLY BE SERVICED BY AN AUTHORIZED AGENT.

Winco Commercial Rotating Heated & Humidified Holding Display Merchandiser Instruction Manual  & troubleshooting 20

HEAT & HUMIDITY CONTROLLED AIRFLOW KEEPS HOT FOODS FRESHER LONGER

The airflow pattern of the EDM-1K by Winco® is designed to maintain consistent temperature and humidity around the food without drying, and
enable the merchandiser to recover temperature quickly after opening/closing the door.

FOOD HOLDING GUIDE

FOOD TYPE MAXIMUM HOLD
TIME > Hours
TEMPERATURE SETTING HUMIDITY LEVEL SETTING
Bagels/Breads/ Croissants/Rolls 4 140°F/60°C 1 (low)
Baked Potatoes 3 150°F/65°C 3 (medium)
Biscuits 2 130°F/55°C 4 (medium/high)
Chicken > Roasted 4 175°F/80°C 5 (high)
Chicken > Fried 4 157°F/80°C 1 (low)
French Fries 1 140°F/60°C 1 (low)
Pies > Fruit 3 180°F/82°C 4 (medium/high)
Hot Dogs 4 185°F/85°C 5 (high)
Onion Rings 1 175°F/80°C 1 (low)
Pizza > Thick Crust 1 185°F/85°C 4 (medium/high)
Pizza > Thin Crust 1 180°F/82°C 5 (high)
Pretzels 3 140°F/60°C 4 (medium/high)
Sandwiches, Wrapped 2 180°F/82°C 4 (medium/high)
NOTE: All times and settings are recommendations only and may vary depending on product preparation, cooking time, and internal food
temperature.

Troubleshooting

If your WINCO commercial equipment does not operate, please check the following prior to placing a service call.

PROBLEM POSSIBLE CAUSE RECOMMENDED SOLUTION
The unit is not turning on Power supply Check that the power supply cord is correctly plugged in and the outlet is working.
The power switch is in the “OFF” position Check that the unit is correctly plugged in and turned on.
Plug/cord or external/internal wiring is faulty Check for loose wire connections and secure properly – Replacement must be done by an authorized service provider.
Defective OWOFF switch Power off and replace OWOFF switch – Replacement must be done by an authorized service provider.
The unit is on but not heating up Temperature is set too low Check that the unit is set to the correct temperature.
Faulty control board Remove and replace – Replacement must be done by an authorized service provider.
Faulty heating element
Incorrect voltage to the heating element Check input power for correct voltage -Must be done by an authorized service provider.
High limit thermal disk is tripped/open Turn the unit off and allow it to cool down and reset.
Very low humidity in the unit Water is low or empty Add water
Humidity is set too low Check humidity setting and raise as needed.
The blower fan is not running Check for correct voltage at the fan. Remove and replace the fan if needed – Replacement must be done by an authorized service provider.
Air temperature is too low Adjust the air temperature to a higher setting
The rack is not spinning Door is open Check door is closed
No power at the supply motor Check for faulty door switch

If needed remove and replace the door switch -Replacement must be done by an authorized service provider.

Debris in the way, stopping the rack Check and remove debris obstructing the rack from spinning
Light is not on light bulb burnt out Remove and replace Replacement must be done by an authorized service provider.
Faulty light ballast
ERROR CODE CAUSE RECOMMENDED SOLUTION
LO H2O Low water Add more water
LO H2O is flashing but water the level is at MAX The low water level switch is faulty Remove and replace – Replacement must be done by an

authorized service provider.

Service and Repair
THIS EQUIPMENT MUST ONLY BE SERVICED BY AN AUTHORIZED AGENT.

NOTE
Parts protected by the manufacturer or its agent are not to be adjusted by the installer unless the installer is an authorized service agent.
If you have any questions or problems DO NOT send the unit to WINCO® without first contacting our customer service department.
See the “Limited Warranty” section on page 14 for details.

Electrical Diagram

MODEL: EDM-1K

Winco Commercial Rotating Heated & Humidified Holding Display Merchandiser Instruction Manual  & troubleshooting 21

This circuit diagram has been provided to assist qualified electricians; only WINCO service agents or qualified electricians should carry out repairs if required.
Do not remove any components or service panels on this product.

Exploded View

MODEL: EDM-1K

Winco Commercial Rotating Heated & Humidified Holding Display Merchandiser Instruction Manual  & troubleshooting 22

Parts List

MODEL: EDM-1K

# Description Part #
1 Left Feet EDM1-P1
2 Right Feet EDM1-P2
3 Clip EDM1-P3
4 0 Ring EDM1-P4
5 Inlet Pipe EDM1-P5
6 Infall Box Cover EDM1-P6
7 Infall Box EDM1-P7
8 Circuit Board EDM1-P8
9 ON/OFF Switch EDM1-P9
10 Ballast EDM1-P10
11 LED Lamp EDM1-P11
12 Transformer EDM1-P12
13 Side Glass EDM1-P13
14 Microswitch (Door) EDM1-P14
15 Front Glass (Customer-Facing) EDM1-P15
16 Motor EDM1-P16
17 Spring EDM1-P17
18 Upper Clutch EDM1-P18
19 Lower Clutch EDM1-P18L
20 Metal Bearing EDM1-P19
21 Motor/Clutch Assembly EDM1-P31
22 Door Assembly EDM1-P20
23 Controller EDM1-P21
24 Water Level Sensor (Lower) EDM1-P22
25 Temperature Sensor (Inner) EDM1-P23
26 Water Level Sensor (Upper) EDM1-P24
27 Drain Valve EDM1-P25
28 Temperature Sensor (Outer) EDM1-P26
29 Heating Element 1 EDM1-P27
30 Heating Element 2 EDM1-P28
31 Fan Motor EDM1-P29
32 4-tier 18″ Round Rack EDM1-P39

Please contact the factory for special order parts not listed.

Limited Warranty

WINCO® warrants to the original purchaser of new equipment that said equipment, when installed in accordance with our instructions within North America and subject to normal use, is free from defects in material or workmanship for a period of 1 year. The labor warranty is one year from the original installation or 18 months from the actual factory shipment date, whichever date occurs first.

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, WHETHER EXPRESSED OR IMPLIED. WINCO EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY OR EXPRESSED OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

WINCO’S OBLIGATION AND LIABILITY UNDER THIS WARRANTY IS EXPRESSLY LIMITED TO REPAIRING AND REPLACING EQUIPMENT

THAT PROVES TO BE DEFECTIVE IN MATERIAL OR WORKMANSHIP WITHIN THE APPLICABLE WARRANTY PERIOD.
IN NO EVENT SHALL WINCO BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES TO BUYER OR ANY THIRD PARTY, INCLUDING, WITHOUT LIMITATION, LOSS OF PROPERTY, PERSONAL INJURY, LOSS OF BUSINESS OR PROFITS OR OTHER ECONOMIC

LOSSES, OR STATUTORY OR EXEMPLARY DAMAGES, WHETHER IN NEGLIGENCE, WARRANTY, STRICT LIABILITY, OR OTHERWISE.

This warranty is given only to the first purchaser from a retail dealer. No warranty is given to subsequent transferees.

Warranty does not cover product failures caused by: failure to maintain, neglect, abuse, damage due to excess water, fire, normal wear, improper setup, and use. Periodic maintenance is not covered.

This warranty is not in force until such time as a properly completed and digitally signed Installation/Warranty Registration has been received by WINCO within 30 days from the date of installation.

WARRANTY SERVICE

To initiate warranty service contact:
email: [email protected]
or call: 973-295-3899
DO NOT send the unit to WINCO® without first contacting our customer service department.

REGISTER ONLINE AT:
www.wincous.com
Proof of purchase is required to extend the warranty more than 1 year from the date of shipment from the factory.

Limited Warranty

THE FOREGOING WARRANTY PROVISIONS ARE A COMPLETE AND EXCLUSIVE STATEMENT BETWEEN THE BUYER AND SELLER. WINCO® NEITHER ASSUMES NOR AUTHORIZES ANY PERSONS TO ASSUME FOR IT ANY OTHER OBLIGATION OR LIABILITY IN CONNECTION WITH SAID EQUIPMENT.
Examples of items not covered under warranty, but not limited to just these items:

  1.  Acts of God, fire, water damage, burglary, accident, theft.
  2. Freight damage.
  3. Improper installation or alteration of the equipment.
  4. Use of generic or after-market parts.
  5. Repairs made by anyone other than a WINCO® designated service provider.
  6. Lubrication.
  7. Expendable wear parts, adjustable feet, blown fuses, lamps, etc.
  8. Cleaning of equipment.
  9. Misuse or abuse.

Please keep this manual in a safe place for future use!

Model: EDM-1K
www.wincous.com

FAQ


Setting up Winco Commercial Rotating Heated & Humidified Holding Display Merchandiser Instruction Manual is easy with these step-by-step instructions. Follow the steps are you are set-up in no time.

Using Winco Commercial Rotating Heated & Humidified Holding Display Merchandiser Instruction Manual is simple by using this manual. Follow the instructions one by one and everything will be fine

Is Winco Commercial Rotating Heated & Humidified Holding Display Merchandiser Instruction Manual stuck or not working properly? By resetting it you can set it back to the standard settings and everything should be back to normal. This works in many cases when problems arise.

This page contains the complete user instructions & manual for Winco Commercial Rotating Heated & Humidified Holding Display Merchandiser Instruction Manual

All symbols, colors and codes for Winco Commercial Rotating Heated & Humidified Holding Display Merchandiser Instruction Manual are explained in this instruction manual. You can find everything you need and moree