WORX WG779E Cordless Lawn Mower Instructions

WORX WG779E Cordless Lawn Mower Instructions & troubleshooting

WORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 1WORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 2

WORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 3

Cordless Lawn Mower
WG779E WG779E.1
WG779E.2 WG779E. 9
Original instructions
WORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 4

WORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 5 WORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 6 WORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 7
WORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 8 WORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 9

TECHNICAL DATA

Type WG779E WG779E.1 WG779E.2 WG779E.9 (770-794 – designation of machinery, representative of Cordless Lawn Mower)

WG779E I WG779E.1 I WG779E.2 I WG779E.9
Rated voltage 20V= Max”
No load speed 3300 / 3500/min
Cutting diameter 34cm
Cutting height 20-70mm
Cutting height positions 6
Grass collection capacity 30L
Battery capacity 2.5Ah I 4.0Ah I 2.0Ah
Battery type Lithium-Ion /
Charging time(approx)
Battery pack:
2.0Ah (1pc) Approx. 1hr /
2.0Ah (2pcs) Approx. 2hrs
2.5Ah (1pc) Approx. 1.25hrs
2.5Ah (2pcs) Approx. 2.5hrs
4.0Ah (1pc) Approx. 2hrs
4.0Ah (2pcs) Approx. 2hrs
Charger rating Input: AC 100-
240V, 50/60Hz,
Output: 20V
DC, 2.0A
Input: AC 100-
240V, 50/60Hz,
Output: 20V
DC, 4.0A
Input: AC 100-
240V, 50/60Hz,
Output: 20V DC,
2.0A
/
Machine Weight 12.1 kg 12.6kg 11.9kg 11.2kg

** Voltage measured without workload. The initial battery voltage reaches a maximum of 20 volts. The nominal voltage is 18 volts.

NOISE DATA

A weighted sound pressure L pA : xxdB (A)
KpA =3dB(A)
A weighted sound power L was : xx dB (A)
Wear ear protection. WORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 10

VIBRATION INFORMATION

Typical weighted vibration ah =xx m/s 2
uncertainty K=1.5m/s²

WORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 11 WARNING: The vibration emission value during actual use of the power tool can differ from the declared value depending on the ways in which the tool is used depending on the following examples and other variations on how the tool is used: How the tool is used and the materials being cut or drilled. The tool is in good condition and well maintained Using the correct accessory for the tool and ensure it is sharp and in good condition. The tightness of the grip on the handles and if any anti-vibration accessories are used. And the tool is being used as intended by its design and these instructions.

This tool may cause hand-arm vibration syndrome if its use is not adequately managed
WORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 12 WARNING: To be accurate, an estimation of exposure level in the actual conditions of use should also take account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle but not actually doing the job. This may significantly reduce the exposure level over the total working period.

Helping to minimize your vibration exposure risk.
ALWAYS use sharp chisels, drills and blades Maintain this tool in accordance with these instructions and keep well lubricated (where appropriate) If the tool is to be used regularly then invest in anti-vibration accessories. Plan your work schedule to spread any high vibration tool use across a number of days.

ACCESSORY

WG779E WG779E.1 WG779E.2 WG779E.9
Grass collection bag 1 1 1 1
Cable clip 2 2 2 2
Roller for stripe / / 1 /
Battery pack (WA3572) 2 / / /
Battery path (WA3553) / 2 / /
Battery path (WA3551) / / 2 /
Charger (WA3869) 1 / 1 /
Charger (WA3876) / 1 / /

We recommend that you purchase your accessories from the same store that sold you the tool. Refer to the accessory packaging for further details. Store personnel can assist you and offer advice.

PRODUCT SAFETY GENERAL POWER TOOL SAFETY WARNINGS

WORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 13 WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire, and/or serious injury.

Carefully read the instructions for the safe operation of the machine. Save all warnings and instructions for future reference.

  • This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities,or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
  • Children should be supervised to ensure that they do not play with the appliance.
  • The appliance is only to be used with the power supply unit provided with the appliance.

IMPORTANT-READ CAREFULLY BEFORE USE KEEP FOR FUTURE  REFERENCE Safe operation practices

TRAINING

a) Read the instructions carefully. Be familiar with the controls and the proper use of the equipment;
b) Never allow children or people unfamiliar with these instructions to use the lawnmower. Local regulations can restrict the age of the operator;
c) Never mow while people, especially children, or pets are nearby;
d) Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their property.

PREPARATION

a) While mowing, always wear substantial footwear and long trousers. Do not operate the equipment when barefoot or wearing open sandals;
b) thoroughly inspect the area where the equipment is to be used and remove all objects which can be thrown by the machine;
c) Before using, always visually inspect to see that the blades, blade bolts, and cutter assembly are not worn or damaged. Replace worn or damaged blades and bolts in sets to preserve balance;
d) On multi-bladed machines, take care as rotating one blade can cause other blades to rotate.

OPERATION

a) mow only in daylight or in good artificial light;
b) avoid operating the equipment in wet grass, where feasible;
c) always be sure of your footing on slopes;
d) walk, never run;
e) for wheeled rotary machines, mow across the face of slopes, never up and down;
f) exercise extreme caution when changing direction on slopes;
g) do not mow excessively steep slopes;
h) use extreme caution when reversing or pulling the lawnmower towards you;
i) stop the blade(s) if the lawnmower has to be  tilted for transportation when crossing surfaces other than grass, and  when transporting the lawnmower to and from the area to be mowed;
j) never operate the lawnmower with defective guards, or without safety devices, for example, deflectors and/or grass catchers, in place;
k) switch on the motor carefully according to instructions and with feet well away from the blade(s);
l) do not tilt the lawnmower when switching on the motor, except if the lawnmower has to be tilted for starting In this case,do not tilt it more than absolutely necessary and lift only the part which is away from the operator;
m) do not put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times;
n) not to touch the blades before the disabling device  has been removed and the blades have come to a complete stop;
o) Do not start the lawnmower when standing in front of the discharge opening.
p) Do not transport the lawnmower while the power source is running.
q) Stop the lawnmower, and remove the disabling device. Make sure that all moving parts have come to a complete stop.
– whenever leaving the machine unattended,
– before clearing a blockage,
– before checking, cleaning or working on the machine,
– after striking a foreign object. Inspect the machine for damage and make repairs before restarting and operating the lawnmower If the lawnmower starts to vibrate abnormally (check immediately)
– inspect for damage.
– replace or repair any damaged parts.
– check and tighten any loose parts.

MAINTENANCE AND STORAGE

a) Keep all nuts, bolts, and screws tight to be sure the equipment is in safe working condition;
b) Check the grass catcher frequently for wear or deterioration;
c) Replace worn or damaged parts for safety. Use only genuine replacement parts and accessories.
d) Be careful during adjusting the lawnmower to prevent entrapment of the fingers between moving blades and fixed parts of the lawnmower.
e) Always allow the lawnmower to cool down before storing.
f) When servicing the blades be aware that, even though the power source is switched off, the blades can still be moved.

SAFETY WARNINGS FOR BATTERY PACK
a) Do not dismantle, open or shred cells or battery packs.
b) Do not short-circuit a battery pack. Do not store battery packs haphazardly in a box or the drawer where they may short-circuit each other or be short-circuited by conductive materials.
When the battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws, or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
c) Do not expose the battery pack to heat or fire. Avoid storage in direct sunlight.
d) Do not subject the battery pack to mechanical shock.
e) In the event of battery leaking, do not allow the liquid to come into contact with the skin or eyes. If contact has been made, wash the affected area with copious amounts of water and seek medical advice.
f) Seek medical advice immediately if a cell or battery pack has been swallowed.
g) Keep the battery pack clean and dry.
h) Wipe the battery pack terminals with a clean dry cloth if they become dirty.
i) Battery pack needs to be charged before use. Always refer to this instruction and use the correct charging procedure.
j) Do not maintain the battery pack on charge when not in use.
k) After extended periods of storage, it may be necessary to charge and discharge the battery pack several times to obtain maximum performance.
l) Battery pack gives its best performance when it is operated at normal room temperature (20°C±5°C).
m) When disposing of battery packs, keep battery packs of different electrochemical systems separate from each other.
n) Recharge only with the charger specified by WORX. Do not use any charger other than that specifically provided for use with the equipment.
A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
o) Do not use any battery pack which is not designed for use with the equipment.
p) Keep the battery pack out of the reach of children.
q) Retain the original product literature for future reference.
r) Remove the battery from the equipment when not in use.
s) Dispose of properly.

SYMBOLS

WORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 14 Read the instruction handbook before operating this machine
WORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 15 Keep bystanders away
WORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 16 Beware of sharp blades. Blades continue to rotate after the motor is switched off- Remove disabling device before maintenance.
WORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 17 Do not expose to rain or water
WORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 18 Do not burn
WORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 19 Do not dispose of batteries. Return exhausted batteries to your local collection or recycling point.
WORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 20 Wear protective gloves
WORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 21 Remove the battery from the socket before carrying out any adjustment, servicing or maintenance.
WORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 22 The blade continues to rotate after the machine is switched off. Wait until all machine components have completely stopped before touching them
WORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 23 Remove the key
WORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 24 Waste electrical products must not be disposed of with household waste. Please recycle where facilities exist. Check with your local authorities or retailer for recycling advice.

OPERATION INSTRUCTION

WORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 25 NOTE: Read the instruction handbook before operating this machine.

INTENDED USE
This product is intended for domestic lawn mowing.

ASSEMBLY AND OPERATION 

ACTION FIGURE
ASSEMBLY  
Assembling the handlebar See Fig. A1, A2, A3, A4, A5
Assembling grass collection bag See Fig.B1, B2, B3, B4
Fitting grass collection bag to  the lawn mower
NOTE: Depress the grass collection bag slightly to ensure that it is completely installed.
See Fig C1, C2, C3
Removing/Emptying Grass Collection Bag
WORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 26 WARNING! Always check the safety flap close the discharge outlet before using. Never lift the safety flap when the lawnmower is being used without a fitted grass collection bag.
See Fig C4
Checking the battery charge condition See Fig. D1
Charging the battery pack Always fully charge the two batteries at the same time, More details can be found charger’s manual See Fig. D2
Fitting/Removing Battery
NOTE: This mower will only run with 2 batteries installed. Please always use the same two batteries and charge the two batteries at the same time.
See Fig. E
OPERATION  

The battery power indicator on the machine See details in BATTERY STATUS part
WORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 27 IMPORTANT
When only one light is illuminated, at least one of the battery is depleted and needs to be charged, even though the mower may still be capable of cutting grass continuing to operate your lawnmower with the battery in this discharged condition may reduce the life and performance of your battery. When no light is illuminated, at least one battery is not fully installed or the battery is defective, please double-check the batteries are fully seated into position.

See Fig. F
Starting & Stopping See Fig. G1, G2
Adjusting the Cutting Height
WORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 28 WARNING! Stop, release the switch lever and wait until the motor stops before adjusting the height. The blades continue to rotate after the machine is switched off, the rotating blades can cause injury not touching rotating blades.
See Fig. H
Selecting the work mode dial ECO mode Select ECO mode when mowing in everyday conditions, removing approximately 20mm of grass at a time.
TURBO mode Set the dial to TURBO mode when cutting dense or overgrown grass.
See Fig. I1, I2
 Grass Bag Filling Indicator Empty status: flap floats (a)
WORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 29
Fully status: flap falls down (b)

WORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 30

See Fig. J
Rear discharge See Fig. K
STORAGE See Fig. L1, L2

The cutting area can be affected by several factors, such as cutting height, lawn humidity, grass length and density. Besides, starting and stopping the mower too many times during operation will reduce the cutting area. The table below gives the relationship between cutting conditions and cutting area.

CUTTING AREA

Cutting co conditions Cutting area (ma mum)
Grass conditions Cutting height WG779E WG779E.1 WG779E.2
Very thin,
dry grass
cut 8cm to 6cm 280m2* 460m2* 230m2*
Thin, dry grass cut 8cm to 4cm 140m2* 230m2* 115m2*

* Used with two fully charged battery packs.
TIPS:

  1. It is recommended to mow your lawn more frequently, walk at a normal pace, and not to start/ stop the mower too often during operation. Please always use the same two batteries and charge the two batteries at the same time.
  2. For best performance, please ensure to use a fully charged battery pack and always cut off 1/3 or less of the grass height.
  3. Walk slowly when cutting long grass, so as to have more effective cutting and properly discharge the clippings.
  4. Avoid cutting wet grass, otherwise, it will stick to the underside of the deck and the clippings cannot be collected or discharged properly.
  5. A higher cutting height shall be applied to new or thick grass and it will extend the battery duration.

BATTERY STATUS (See Fig. F)
Before starting or after use, press the button “POWER TEST” on the machine to check the battery capacity. During operation, the battery capacity will be indicated automatically by the battery power indicator. The indicator constantly senses and displays the battery condition as follows:

Battery power indicator status Battery condition
Five green lightsWORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 31 are illuminated. The two batteries are in a
highly charged condition.
Two, three or four green lights are illuminated. The two batteries have a remaining charge. The more lights are illuminated the more battery capacity.
Only one green light WORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 32is illuminated. At least one battery is depleted and needs to be charged.
No light is illuminated. ill At least one battery is not fully installed or the battery is defective.
Only one light WORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 33Clashing twice per cycle. At least one battery is over-discharged, please recharge the two batteries at once before use again or storage.
Only one lightWORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 34 is flashing three times per cycle. At least one battery is hot, wait for them to cool down before starting again.
Only one lightWORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 35 is Bashing tour times per cycle. The machine is overloaded. Raise the cutting height or push slowly.

MOWING TIPS
NOTE: ALWAYS INSPECT THE AREA WHERE MOWER IS TO BE USED AND REMOVE ALL STONES, STICKS, WIRE, METAL AND OTHER DEBRIS WHICH MIGHT BE THROWN BY THE ROTATING BLADE.

  1. Mow across the face of slopes, never up and down. Exercise extreme caution when changing direction on slopes. Do not mow excessively steep slopes. Always maintain good footing.
  2. Release the switch lever to turn the mower “OFF” when crossing any graveled area (stones can be thrown by the blade).
  3. Set mower at highest cutting height when mowing in the rough ground or in tall weeds. Removing too much grass at one time can cause the circuit breaker to trip, which stops the mower.
  4. If a grass bag is used during the fast-growing season, the grass may tend to clog up at the discharge opening. Release the switch lever to turn the mower “OFF” and remove the safety key. Remove the grass bag and shake the grass down to the back end of the bag. Also, clean out any grass or debris which may be packed around the discharge opening. Replace the grass collection bag.
  5. If the mower should start to vibrate abnormally, release the switch lever to turn the mower “OFF” and remove the safety key. Check immediately for cause. Vibration is a warning of trouble. Do not operate the mower until a service check has been made.
  6. ALWAYS RELEASE THE SWITCH LEVER TO TURN THE MOWER “OFF” AND REMOVE THE SAFETY KEY WHEN LEAVING IT UNATTENDED EVEN FOR A SHORT PERIOD OF TIME.

MAINTENANCE

WORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 36 WARNING: Stop the mower and remove the safety key before removing the grass bag.
Note:
To ensure long and reliable service, perform the following maintenance procedures regularly. Check for obvious defects such as loose, dislodged, or damaged blades, lose fittings, and worn or damaged components. Check that the covers and guards are all undamaged and are correctly attached to the mower. Carry out any necessary maintenance or repairs before the operating mower. If the mower should happen to fail despite regular maintenance, please call our customer helpline for advice.

BLADE SHARPENING
KEEP BLADE SHARP FOR BEST MOWER PERFORMANCE.
WEAR PROPER EYE PROTECTION WHILE REMOVING, SHARPENING, AND INSTALLING BLADES. ENSURE THAT THE SAFETY KEY IS REMOVED.
Sharpening the blade twice during a mowing season is usually sufficient under normal circumstances.  Sand causes the blade to dull quickly. If your lawn has sandy soil, more frequent sharpening may be required.
REPLACE BENT OR DAMAGED BLADE IMMEDIATELY.

WHEN SHARPENING THE BLADE:

  1.  Make sure the blade remains balanced.
  2. Sharpen the blade at the original cutting angle.
  3.  Sharpen cutting edges on both ends of the blade, removing equal amounts of material from both ends.

Note:

  1. Be sure the mower is turned off and remove the key.
  2. Place the mower in stand-up storage mode.

TO SHARPEN BLADE IN A VISE (SEE Fig. M)

  1. Be sure the switch lever is released, the blade has stopped and the safety key is removed before removing the blade.
  2. Remove blade from mower. See instructions for removing and attaching the blade.
  3. Secure blade M-1 in a vise M-2.
  4. Wear safety glasses and be careful not to cut yourself.
  5. Carefully file the cutting edges of the blade with a fine tooth file M-3 or sharpening stone.
  6. Check the balance of the blade. See instructions for blade balancing.
  7. Replace blade on mower and tighten securely. Refer to the instructions below.

BLADE BALANCING (SEE Fig. N)
Check the balance of the blade by placing a center hole in the blade N-1 over a nail or screwdriver shank N-2, clamped horizontally in a vise N-3. If either end of the blade rotates downward, file that end. The blade is properly balanced when neither end drops.

BLADE MAINTENANCE (See Fig. O1, O2)
Renew your metal blade after 50 hours of mowing or 2 years, whichever is the sooner-regardless of condition. Follow these procedures to remove and replace the blade. You will need garden gloves (not provided) and a spanner wrench (not provided) to remove the blade. Hold the blade (16) and unscrew the blade bolt (15) counter-clockwise using a  spanner wrench, and then remove the blade. To re-assemble, position the blade (16) with the cutting edges towards the ground. Then securely tighten the blade bolt (15).

STORAGE (See Fig. L1, L2)
Stop the mower and always remove the safety key. Clean the exterior of the machine thoroughly using a soft brush and cloth. Do not use water, solvents, or polishes. Remove all grass and debris, especially from the ventilation slots. Turn the machine on its side and clean the blade area. If grass cuttings are compacted in the blade area, remove them with a wooden or plastic implement. Store the machine in a dry place. Do not place other objects on top of the machine. To aid storage, release the handle knob, and fold the upper handle as shown in Fig. L1 & L2.

ENVIRONMENTAL PROTECTION

WORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 37 Waste electrical products must not be disposed of with household waste. Please recycle where facilities exist. Check with your local authorities or retailer for recycling advice.

TROUBLESHOOTING

Problem Solution
1. Mower doesn’t run when the switch lever is activated. A.Check to make sure the safety key has been installed and is fully seated and that button on the switch housing is being completely pushed.
B.Release Switch Lever to turn mower off. Remove the safety key, turn the mower over and check that blade is free to turn. If not free, return to an authorized servicer. The blade should turn freely.
C. Has the battery been fully charged? Plugin the charger and wait for the green light to come on.
2. Motor stops while mowing. A.Release Switch Lever to turn the mower off. Remove the safety key, turn the mower over and check that blade is free to turn. If not free, return to an authorized servicer. The blade should turn freely.
B.Raise cutting height of wheels to the highest position and start the mower.
Has
C. Has the battery been fully charged? Plugin the charger and wait for the green light to come on.
D.Avoid overloading the mower. Slow down the cutting pace by pushing the mower slower or raising the cut height. Or both.
3. Mower runs but cutting performance is unsatisfactory, or does not cut entire lawn. Has A.Has the battery been fully charged? Plugin the charger and wait for the green light to come on.
B.Release Switch Lever to turn mower off. Remove the safety key. Tum mower over and check: Blade for sharpness – Keep the blade sharp. Deck and discharge chute for clogging.
C.Wheel height adjustment may be set too low for grass conditions. Raise cutting height.
4. Mower is too hard to push. A. Raise cutting height to reduce deck drag on grass. Check each wheel for free rotation.
5. Mower is abnormally noisy and vibrates. A.Release Switch Lever to turn the mower off. Remove the safety key. Turn the mower on the side and check the blade to ensure it has not been bent or damaged. If the blade is damaged, replace it with a replacement blade. If the underside of the deck is damaged return the mower to an authorized service center.
B.If there is no visible damage to the blade and the mower still vibrates: Release Switch Lever to turn the mower off, remove the safety key and remove the blade. Rotate blade 160 degrees and retighten. If the mower still vibrates, return the mower to an authorized service center.
6. Battery charger LED’s not on. A.Check plug connection.
B.Replace charger.
7 Battery charger LED does not flip to green. A. Battery needs to be diagnosed. Take to authorized service center.
6. Mower not picking up clippings with the Grass Collection Bag. A.Remove mulch plate when bagging.
B.Chute clogged. Release Switch Lever to turn the mower off. Remove the safety
key. Clear chute of grass clippings.
C.Too much cut grass. Raise the cutting height of wheels to shorten the length of the cut.
D. Bag full. Empty bag more often.
9. When mulching there are clippings visible. A.Too much cut grass. Raise the cutting height of wheels to shorten the length of the cut. Do not cut off more than 1/3 of the total length.
B. Check blade for sharpness Always keep the blade sharp.
10. Low or diminished run-time after many uses. A. Return to Authorized Service location – may need a new battery.
11.The battery charger LED flashes red and the battery can’t be charged. A.The battery overheats after continuous use. Remove the battery from the charger and allow it to cool to 42°C or less.

DECLARATION OF CONFORMITY

We, POSTED Germany GmbH Konrad-Adenauer-Ufer 37 50668 Köln
Declare that the product
Description: WORX Cordless Lawn Mower
Type: WG779E WG779E.1 WG779E.2
WG779E.9 (770-794- designation of machinery, representative of Cordless Lawn Mower)
Function: Mowing grass
Complies with the following Directives,
2006/42/EC, 2014/30/EU, 2011/65/EU,
2000/14/EC amended by 2005/88/EC
2000/14/EC amended by 2005/88/EC
Conformity assessment procedure as per Annex VI
Measured Sound Power Level xx dB(A)
Declared Guaranteed Sound Power Level xx dB(A)
The notified body involved
Name: Intertek Testing & Certification Ltd  (notified body 0359)
Address: Davy Avenue, Knowlhill, Milton
Keynes, MK5 8NL
Standards conform to,
EN 60335-1
EN 60335-2-77
EN 62233
EN ISO 3744
EN 55014-1
EN 55014-2

The person authorized to compile the technical file,
Name: Russell Nicholson
Address: Positec Power Tools (Europe)Ltd,
PO Box 6242, Newbury, RG14 9LT, UK
WORX WG779E Cordless Lawn Mower Instructions  & troubleshooting 38
Suzhou 2017/08/30
Allen Ding
Deputy Chief Engineer, Testing & Certification
Cordless Lawn Mower

FAQ


Setting up WORX WG779E Cordless Lawn Mower Instructions is easy with these step-by-step instructions. Follow the steps are you are set-up in no time.

Using WORX WG779E Cordless Lawn Mower Instructions is simple by using this manual. Follow the instructions one by one and everything will be fine

Is WORX WG779E Cordless Lawn Mower Instructions stuck or not working properly? By resetting it you can set it back to the standard settings and everything should be back to normal. This works in many cases when problems arise.

This page contains the complete user instructions & manual for WORX WG779E Cordless Lawn Mower Instructions

All symbols, colors and codes for WORX WG779E Cordless Lawn Mower Instructions are explained in this instruction manual. You can find everything you need and moree