ZYXEL RGS200-12P 12-Spot Gbe Managed PoE Switch User Guide

ZYXEL RGS200-12P 12-Spot Gbe Managed PoE Switch User Guide & troubleshooting

ZYXEL RGS200-12P 12-Spot Gbe Managed PoE Switch User Guide  & troubleshooting 1

ZYXEL RGS200-12P 12-Spot Gbe Managed PoE Switch

ZYXEL RGS200-12P 12-Spot Gbe Managed PoE Switch User Guide  & troubleshooting 2

Overview

The RGS200-12P Managed Rugged switch is designed for supporting environmental hardening application. Managed switches are easier to prioritize, partition, and organize user’s network, providing a more reliable and better quality services.

Dimension Illustration

ZYXEL RGS200-12P 12-Spot Gbe Managed PoE Switch User Guide  & troubleshooting 3

DIN-Rail Mounting

Mounting step

  1. Screw the DIN-Rail bracket on with the bracket and screws in the accessory kit.
  2. Hook the unit over the DIN rail.
  3. Push the bottom of the unit towards the DIN Rail until it locks in place..

ZYXEL RGS200-12P 12-Spot Gbe Managed PoE Switch User Guide  & troubleshooting 4

Wall Mounting

Screw the wall-mount brackets with screws in the accessory kit.

ZYXEL RGS200-12P 12-Spot Gbe Managed PoE Switch User Guide  & troubleshooting 5

Connecting Power Terminal Block

The switch can be powered from two power supplies (input range 12V- 58V). Insert the positive and negative wires into V+ and V­contacts on the terminal block respectively and tighten the
wire-clamp screws to prevent the wires from being loosened.

  • The DC power should be connected to a well-fused power supply.
  • Input power should be within the range of 54-58VDC for PoE+ compliant, or 48-58VDC for PoE compliant.

ZYXEL RGS200-12P 12-Spot Gbe Managed PoE Switch User Guide  & troubleshooting 6

This equipment is intended to be used in a Restricted Access Location, with access limited to SERVICE PERSONAL and USERS authorized to be in that location.

Alarm Relay and Ground

The alarm relay output contacts are in the middle of the DC terminal block connector as shown in the figure below.
The alarm relay out is “Normal Open”, and it will be closed when detected any predefined failure such as power failures or Ethernet link failures.
The relay output with current carrying capacity of [email protected] 24 VDC

ZYXEL RGS200-12P 12-Spot Gbe Managed PoE Switch User Guide  & troubleshooting 7

Console Connection

  • D89 connector connect to computer COM port
    • Baud rate: 115200bps
    • 8 data bits, 1 stop bit
    • No Parity
    • None flow control

Connect & Login to Managed Switch

  1. Connecting to the Ethernet port (RJ45 Ethernet port) of Managed Switch.
  2. Factory default IP: 192.168.1.1
  3. Login with default account and password.
    Username: admin
    Password: 1234

Support Information
USA
Tel: + 1 800 255 4101
Email: [email protected]

EU
Visit: https://support.zyxel.eu

EU Importer
ZyXEL Communication A/S
Generatorvej 8D, 2860 S0borg, Denmark. https://www.zyxel.com/dk/da/
US Importer
ZyXEL Communications, Inc
1130 North Miller Street Anaheim, CA 92806-2001 https://www.zyxel.com/us/en/

ZYXEL RGS200-12P 12-Spot Gbe Managed PoE Switch User Guide  & troubleshooting 8

FAQ


Setting up ZYXEL RGS200-12P 12-Spot Gbe Managed PoE Switch User Guide is easy with these step-by-step instructions. Follow the steps are you are set-up in no time.

Using ZYXEL RGS200-12P 12-Spot Gbe Managed PoE Switch User Guide is simple by using this manual. Follow the instructions one by one and everything will be fine

Is ZYXEL RGS200-12P 12-Spot Gbe Managed PoE Switch User Guide stuck or not working properly? By resetting it you can set it back to the standard settings and everything should be back to normal. This works in many cases when problems arise.

This page contains the complete user instructions & manual for ZYXEL RGS200-12P 12-Spot Gbe Managed PoE Switch User Guide

All symbols, colors and codes for ZYXEL RGS200-12P 12-Spot Gbe Managed PoE Switch User Guide are explained in this instruction manual. You can find everything you need and moree